[Booklet]
Overview
Set [Binding Position], [Page Margin], [Blank Cover], and others when printing a booklet.
NOTICE
- Saddle Stitcher SD-513 with Trimmer Unit TU-503 mounted is required to set the [2-Side Slitting].
NOTICE
One of the following options is required to select [Output Setting].
- SaddleStitcher SD-506
- Saddle Stitcher SD-513
- Finisher FS-532 with Saddle Stitcher SD-510 mounted
Tips
Booklet printing is not available when
- the imposed image has a different controller image compression setting (Gradation Priority/Resolution Priority).
Tips
- To attach covers to a booklet, load cover paper of the same size as the body set into any Paper tray or the Post inserter tray. For details, refer to [Front Cover Setting] / [Back Cover Setting].
- PostInserter PI-502 is required to feed blank covers from the Post inserter tray.
- The stapled and folded sheets or multi half folded sheets are output to the Bundle exit tray. Set the Extension tray of the bundle exit tray as preparation, and open the Stopper. Otherwise, the output paper may drop down from the Bundle exit tray. Also, the full-load detection function may not work.
Reference
- For details about [Booklet], refer to [Booklet].
Setting Items
Setting item | Description | |
|---|---|---|
[Binding Position] | [Right Bind] | Set the booklet binding direction to Right Bind. Generally, set this item when the text is written vertically. |
[Left Bind] | Set the booklet binding direction to Left Bind. Generally, set this item when the text is written horizontally. | |
[Page Margin] | [ChangePageSpace] | Set the booklet binding margin (margin for binding). Leave a space between the right and left pages by the specified value based on the center of printout. The entered setting value is displayed in the page space setting value display area next to [Front Side] or [Back Side]. |
[Creep Adjustment] | [Change Creep] | Corrects the gap between the inner and outer margins that occurs when the paper is folded in half for binding. Set the offset method and offset amount (shift amount). The entered setting value is displayed in the shift amount adjustment value display field under [Change Creep]. |
[Blank Cover] | [No Cover] | Does not insert a blank cover into the booklet. |
[With Cover] ([Booklet] - Blank Cover - [With Cover]) | Inserts a blank cover into the booklet. | |
[2-Side Slitting] | [ON] | Slits both edges of a booklet. |
[OFF] | Does not slit both edges of a booklet. | |
[Output Setting] | [Fold & Staple] | Set to [ON] to apply Fold & Staple to a booklet. |
[Multi Half Fold] | Set to [ON] to apply Multi Half Fold to a booklet. | |
[Sort] | Delimits printed sheets for each copy when printing. This item cannot be changed because it is fixed for booklet printing. | |
[Function OFF] | Turns the function off while maintaining the set information. | |
Setting Procedure (Setting the Page Space)
Adjusts the page space of the selected print side.
1
Press [ChangePageSpace].
The setting screen is displayed.
2
Select the side to adjust.
Select the desired side from [Front Side], [Back Side], and [Double Sided]. Select [Double Sided] to simultaneously adjust the image positions in the front and back sides.
3
Use the on-screen keypad to enter the numeric value.
Range: -250.0 mm to 250.0 mm
Use [+ / -] to select the positive or negative value.
Pressing [,]/[+] increases or decreases the numeric value in steps of 0.1 mm.
4
Press [OK].
Setting Procedure (Setting the Creep Adjustment Amount)
1
Press [Change Creep].
The setting screen is displayed.
2
Select the target to adjust offset.
[Whole Offset] allows you to adjust the offset amount based on the total number of pages.
[Page Offset] allows you to adjust the offset amount for each page.
3
Use the on-screen keypad to enter the numeric value.
[Whole Offset] setting range: 0.0 mm to 50.0 mm
[Page Offset] setting range: 0.00 mm to 5.00 mm
Pressing [,]/[+] increases or decreases the numeric value in steps of 0.1 mm for [Whole Offset] and 0.01 mm for [Page Offset].
4
Press [OK].
Setting Procedure (Setting [2-Side Slitting])
Specify [Slitting] and [Offset against Cover].
1
Press [ON].
The setting screen is displayed.
2
Select [(1)] or [(2)] of [Slitting], and use the on-screen keypad to enter the slitting amount.
Range: 8.0 mm to 26.0 mm
Pressing [,]/[+] increases or decreases the numeric value in steps of 0.1 mm.
Use [+ / -] to set the plus or minus of the numeric value.
When the slitting amount is different between [(1)] and [(2)] by 10.0 mm or more, its value cannot be entered.
3
Select [Offset against Cover], and use the on-screen keypad to enter the slitting amount of the body for the cover.
Range: -1.0 mm to 1.0 mm
Pressing [,]/[+] increases or decreases the numeric value in steps of 0.1 mm.
4
Press [OK].
in the upper-right of a page, it turns into 
and is registered as a bookmark.