Description of Setup Buttons (Administrator Settings)

Configure the settings to search for destinations from the LDAP server or Active Directory.

Settings		Description
[Enabling LDAP]		Select whether to use the LDAP server to search for a destination. Using this function allows you to search for an E-mail address or fax number via the LDAP server when sending the scanned original data. [OFF] is specified by default.
[Setting Up LDAP]		Register the LDAP server used to search for a destination. Select an unregistered key, and enter the required information.
	[LDAP Server Name]	Enter the name of the LDAP server (using up to 32 characters). Use a name that helps you easily identify the server.
	[LDAP Setting]	Configure settings for LDAP search operations. [Max.Search Results]: Change the maximum number of destinations to be displayed as search results, if necessary. [100] is specified by default. [Timeout]: Change the timeout interval for communication with the LDAP server, if required. [60 sec.] is specified by default. [Initial Setting for Search Details]: Specify the default LDAP search conditions for each item. [OR] is specified by default in every case. [Change Search Attribute]: Select attributes to be specified when performing the LDAP search. The setting can be switched between [Name] (cn) and [Nickname] (displayName). [Name] is specified by default in every case. [Search]: Select whether to display candidate destinations when entering part of a name. [OFF] is specified by default.
	[Server Address]	Enter the LDAP server address. Use one of the following entry formats. Example of host name entry: "host.example.com" Example of IP address (IPv4) entry: "192.168.1.1" Example of IP address (IPv6) entry: "fe80::220:6bff:fe10:2f16"
	[Search Base]	Specify the starting point to search for a user to be authenticated (using up to 255 characters). This option also searches in subdirectories under the entered starting point. Example of entry: "cn=users,dc=example,dc=com"
	[SSL Setting]	Specify whether or not to use SSL for communication with the LDAP server. [OFF] is specified by default.
	[Port Number]	If necessary, change the LDAP server port number. Normally, you can use the original port number. [389] is specified by default.
	[Port Number (SSL)]	If necessary, change the SSL communication port number. Normally, you can use the original port number. [636] is specified by default.
	[Certificate Verification Level Settings]	To validate the certificate during SSL communication, select items to be verified. [Expiration Date]: Confirm whether the certificate is within the validity period. [Confirm] is specified by default. [Key Usage]: Confirm whether the certificate is used according to the intended purpose approved by the certificate issuer. [Do Not Confirm] is specified by default. [Chain]: Confirm whether there is a problem in the certificate chain (certificate path). The chain is validated by referencing the external certificates managed on this machine. [Do Not Confirm] is specified by default. [Expiration Date Confirmation]: Confirm whether the certificate has expired. [Do Not Confirm] is specified by default. [CN]: Confirm whether CN (Common Name) of the certificate matches the server address. [Do Not Confirm] is specified by default.
	[Authentication Type]	Select the authentication method to log in to the LDAP server. Select one appropriate for the authentication method used for your LDAP server. [Anonymous] [Simple] [Digest-MD5] [GSS-SPNEGO] [NTLM v1] [NTLM v2] [Anonymous] is specified by default.
	[Select Server Authentication Method]	Select the LDAP server authentication method. [Use Settings]: Use the settings of [Login Name], [Password], and [Domain Name]. [Use User Authentication]: Synchronizes with the user authentication of this machine. Uses the user name and password of the registered user of this machine as [Login Name] and [Password]. [Dynamic Authentication]: The system prompts you to enter the user name and password at LDAP searching. [Set Value] is specified by default.
	[Referral Setting]	Specify whether to use the referral function as required. Make an appropriate choice that fits the LDAP server environment. [ON] is specified by default.
	[Login Name]	Log in to the LDAP server, and enter the login name to search for a user (using up to 64 characters).
	[Password]	Enter the password of the user name you entered into [Login Name] (using up to 64 characters).
	[Domain Name]	Enter the domain name to log in to the LDAP server (using up to 64 characters). If [GSS-SPNEGO] is selected for [Authentication Type], enter the domain name of Active Directory.
	[Search Attributes Authentication]	Select whether to enable the attribute-based authentication when [Authentication Type] is set to [Simple] and [Select Server Authentication Method] to [Dynamic Authentication]. If enabled, the user does not need to enter all of the DN (Distinguished Name) when performing authentication via the LDAP server. [No Limit] is specified by default.
	[Search Attribute(s)]	Enter the search attribute to be automatically added before the user name (using up to 64 characters). The attribute must start with an alphabet character. [uid] is specified by default.
	[Check Connection]	Select this option to try connecting to the LDAP server using the entered information and check if the information registered is correct. This option is displayed when [ON] is selected in [Enabling LDAP].
	[Reset All Settings]	Press this key to reset all the contents you entered.
[Default LDAP Server Setting]		Select the default LDAP server to search for a destination. When registering multiple LDAP servers, set the frequently used LDAP server as the default.
[Default Search Result Display Setting]		Select the default destination type to be displayed as the destination search result. [E-Mail] is specified by default.

Configure settings for authentication by the LDAP server using the card ID registered on authentication cards in an environment with IC card-based user authentication implemented by connecting an optional Authentication Unit (IC card type).You can set this option by selecting [External Server Authentication] or [Main + External Server] in [Administrator Settings] - [User Authentication/Account Track] - [General Settings] - [User Authentication] - [General Settings].

Settings		Description
[ON]/[OFF]		Specify whether to enable authentication by the LDAP server using the card ID registered on authentication cards. [OFF] is specified by default.
[Setting Up LDAP]		Register the LDAP server to be used for authenticating the user ID of the IC card. Tap [Check Connection] to try connecting to the LDAP server using the entered information and check if the information registered is correct. Tap [Reset All Settings] to reset all the information entered.
	[User Name Acquisition]	Select the method for obtaining the user name for logging in to this machine. [Use Card IC]: Use the card ID on the IC card as the user name. [Acquiring]: Use the user name obtained from the server. Enter the attribute to be searched as the user name (such as "uid") in [User Name Attribute]. [Use Card IC] is specified by default.
	[Timeout]	Change the timeout time of communication with the LDAP server if necessary. [60 second] is specified by default.
	[Search Attribute(s)]	Enter the search attribute to be used for search of a user using the LDAP server (using up to 64 characters). The attribute must start with an alphabet character. [uid] is specified by default.
	[Server Address]	Enter the LDAP server address. Use one of the following entry formats. Example of host name entry: "host.example.com" Example of IP address (IPv4) entry: "192.168.1.1" Example of IP address (IPv6) entry: "fe80::220:6bff:fe10:2f16"
	[Search Base]	Specify the starting point to search for a user to be authenticated (using up to 255 characters). This option also searches in subdirectories under the entered starting point. Example of entry: "cn=users,dc=example,dc=com"
	[SSL Setting]	Specify whether or not to use SSL for communication with the LDAP server. [OFF] is specified by default.
	[Port Number]	If necessary, change the LDAP server port number. Normally, you can use the original port number. [389] is specified by default.
	[Port Number (SSL)]	If necessary, change the SSL communication port number. Normally, you can use the original port number. [636] is specified by default.
	[Certificate Verification Level Settings]	To validate the certificate during SSL communication, select items to be verified. [Expiration Date]: Confirm whether the certificate is within the validity period. [Confirm] is specified by default. [Key Usage]: Confirm whether the certificate is used according to the intended purpose approved by the certificate issuer. [Do Not Confirm] is specified by default. [Chain]: Confirm whether there is a problem in the certificate chain (certificate path). The chain is validated by referencing the external certificates managed on this machine. [Do Not Confirm] is specified by default. [Expiration Date Confirmation]: Confirm whether the certificate has expired. [Do Not Confirm] is specified by default. [CN]: Confirm whether CN (Common Name) of the certificate matches the server address. [Do Not Confirm] is specified by default.
	[Authentication Type]	Select the authentication method to log in to the LDAP server. Select one appropriate for the authentication method used for your LDAP server. [Simple] [Digest-MD5] [GSS-SPNEGO] [NTLM v1] [NTLM v2] [Simple] is specified by default.
	[Referral Setting]	Specify whether to use the referral function as required. Make an appropriate choice that fits the LDAP server environment. [ON] is specified by default.
	[Login Name]	Log in to the LDAP server, and enter the login name to search for a user (using up to 64 characters).
	[Password]	Enter the password of the user name you entered into [Login Name] (using up to 64 characters).
	[Domain Name]	Enter the domain name to log in to the LDAP server (using up to 64 characters). If [GSS-SPNEGO] is selected for [Authentication Type], enter the domain name of Active Directory.
[LDAP-IC Card Authentication Setting]		Select the name of the external server to be used as authentication information saved in this machine The authentication information is saved in this machine when the LDAP-IC card authentication is successfully completed. This authentication information includes the user name and the external server name. As for the external server name in authentication information to be saved in this machine, you can register the name of external server registered on this machine.

Adjust the print start position at the leading edge of the paper relative to the paper discharge direction.Press Start to print a test pattern. Check the test pattern and adjust so that the margin between the leading edge of the paper and the print start position is 3/16 inches (4.2 mm). Repeat adjustments, as required.

Settings	Description
[Paper Type]	Select the type of paper that is used to adjust the start position for printing.
[Adjust Value]	Enter an adjustment value between -3.0 and +3.0 mm by tapping [-] and [+]. [0.0 mm] is specified by default.

Adjust the print start position at the leading edge of the paper relative to the paper discharge direction for printing the back side in 2-sided printing.Press Start to print a test pattern. Check the test pattern and adjust so that the margin between the leading edge of the paper and the print start position is 3/16 inches (4.2 mm). Repeat adjustments, as required.

Settings	Description
[Paper Type]	Select the type of paper that is used to adjust the start position for printing.
[Adjust Value]	Enter an adjustment value between -3.0 and +3.0 mm by tapping [-] and [+]. [0.0 mm] is specified by default.

Select whether to preferentially print an original on inch-sized paper when a fax is received.The default value depends on the country the machine is used in.

Issue a request code required to use an advanced function, or enable an advanced function.

Settings	Description
[Get Request Code]	Issue a request code for this machine to be registered in the license management server (LMS).
[Install License]	Enter information required for enabling advanced functions.
[List of Enabled Functions]	Displays a list of enabled functions.

Limit the access to destinations for each user.Restrict destinations that can be browsed by users by combining [Apply Levels/Groups to Destinations] and [Apply Levels/ Groups to Users].

Settings		Description
[Create Group]		Register a reference allowed group. In a reference allowed group, destinations and users can be registered, and such users can reference destinations registered in the same group. To register a group, select the registration number and tap [Edit]. To check destinations or users registered in a group, tap [Details].
	[Group Name]	Enter the name of the group (using up to 24 characters).
	[Access Allowed Level]	To manage the address book by combining the access allowed level and reference allowed group, select an access allowed level of the reference allowed group. [Level 0] is specified by default.
[Apply Levels/Groups to Destinations]		Select a registered destination from [Address Book], [Group], or [Program], and then configure either the reference allowed group or access allowed level.
	[Apply Group]	Assign a reference allowed group to the registered destination you have selected. Before you can assign a reference allowed group, you need to register the reference allowed group in [Create Group].
	[Apply Level]	Assign an access allowed level to the registered destination you have selected. [Level 0] is specified by default.
[Apply Levels/Groups to Users]		Select a registered user or public user and specify a reference allowed group or access allowed level. You can combine reference allowed group and access allowed level settings.
	[Apply Group]	Assign a reference allowed group to the registered user you have selected. Before you can assign a reference allowed group, you need to register the reference allowed group in [Create Group].
	[Apply Level]	Assign an access allowed level to the registered user you have selected. [Level 0] is specified by default.

Set this option for the dirt detection level for the Slit Scan Glass and cleaning of the Slit Scan Glass.

Settings		Description
[Prior Detection Setting (Front Side)]		Specify whether to issue an alert when the Slit Scan Glass is dirty and set the contamination detection level.
	[Yes]/[No]	Specify whether to detect dirt on the Slit Scan Glass in advance. [Yes] is specified by default.
	[Warning Display]	Select the type of alert that is displayed in the Touch Panel. [TYPE1]: Show an alert icon in the icon display area on the Touch Panel. [TYPE2]: Show an alert message in the message display area on the Touch Panel. [TYPE3]: Show an alert message across Touch Panel. [OFF]: An alert is not displayed. [TYPE1] is specified by default.
	[Detection level]	Select a contamination detection level. [Low]: Make it harder to detect contamination. [Std.]: Detect contamination at an ordinary level. [High]: Make it easy to detect contamination. [Std.] is specified by default.
[Prior Detection Setting (Back Side)]		Specify whether to issue an alert when the Slit Scan Glass for scanning the back side is dirty and set the contamination detection level.
	[Yes]/[No]	Specify whether to detect dirt on the Slit Scan Glass in advance. [Yes] is specified by default.
	[Warning Display]	Select the type of alert that is displayed in the Touch Panel. [TYPE1]: Show an alert icon in the icon display area on the Touch Panel. [TYPE2]: Show an alert message in the message display area on the Touch Panel. [TYPE3]: Show an alert message across Touch Panel. Use the [Warning Display Time] to specify when to display an alert message. [OFF]: An alert is not displayed. [TYPE1] is specified by default.
	[Detection level]	Select a contamination detection level. [Low]: Make it harder to detect contamination. [Std.]: Detect contamination at an ordinary level. [High]: Make it easy to detect contamination. [Std.] is specified by default.
	[Warning Display Time]	Select a timing for displaying a warning message when [TYPE3] is selected for [Warning Display]. [During the Back Side Scan] is specified by default.
[Feed Cleaning Settings]		Specify whether to clean the Slit Scan Glass when scanning an original in the ADF. [Clean] is specified by default.

Select whether to play sounds on the telephone line from speakers during fax communication.[OFF] is specified by default.

If necessary, adjust the volume of speakers when receiving a fax if [Line Monitor Sound] is set to [ON].[20] is specified by default.

If necessary, adjust the volume of speakers when sending a fax if [Line Monitor Sound] is set to [ON].[10] is specified by default.

Configure the environment to use fax functions with this machine, such as the types of telephone lines (dialing method) and fax receive mode.

Settings	Description
[Dialing Method]	Select the line type according to your environment.
[Receive Mode]	Select a receive mode.
[Number of RX Call Rings]	If necessary, change the number of times the phone rings before automatically receiving a fax.
[Number of Redials]	If the machine fails to send a fax successfully, it automatically redials the same destination after the elapse of a certain period of time. If necessary, change the number of redials.
[Redial Interval]	If necessary, change the redial intervals when you specified a value in [Number of Redials].
[Line Monitor Sound]	Select whether to play sounds on the telephone line from speakers during fax communication.
[Line Monitor Sound Volume (Send)]	If necessary, adjust the volume of speakers when sending a fax if [Line Monitor Sound] is set to [ON].
[Line Monitor Sound Volume (Receive)]	If necessary, adjust the volume of speakers when receiving a fax if [[Line Monitor Sound] is set to [ON].

Displays a list of enabled functions.

Prints the job setting list of this machine and configure the paper count.

Settings	Description
[Management List]	Prints a list of job settings on this machine.
[Paper Size/Type Counter]	Register a combination of paper size and paper type to manage counting of used sheets.
[Fax Activity Summary Information]	Specify whether to permit sending of information on the use frequency of the machine and function settings to our company.
[TX Operation Log Output]	Prints logs on send operations or save them on a USB memory.

Select whether to use LLMNR (Link-local Multicast Name Resolution).Using LLMNR enables you to resolve the name even in an environment with no DNS server. This function is supported in an operating system of Windows Vista or later (Windows Vista/7/Server 2008/Server 2008 R2). It is useful to resolve the name in the IPv6 environment.[Disable] is specified by default.

Specify whether to log out automatically when scanning of the original finishes.[Do not log off] is specified by default.

Specify whether to display the logout confirmation screen on the Touch Panel when you log out of the login mode (Recipient User or Public User) entered by pressing Access.[ON] is specified by default.

Select whether to enable the LPD (Line Printer Daemon).Select [Enable] to use the LPR print function.[Enable] is specified by default.