Description of Setup Buttons (User Settings)

Register destination fax numbers.

Settings	Description
[No.]	Destination registration number.[No.] is automatically registered using an unused smaller number. If you want to specify a number, tap [No.] and enter the number within the range of 1 to 2000.
[Name]	Enter the destination name that appears on the Touch Panel (using up to 24 characters). Assign a name that helps you easily identify the destination.
[Sort Character]	Enter the same name as the registered (using up to 24 characters). You can sort destinations by registration name.
[Index]	Select a corresponding character so that the destination can be index-searched by registration name. If an alphabet character is specified for the initial of a registration name, search text is automatically specified with the alphabet character. If anything other than alphabet character is specified for the initial of a registration name, [etc] is specified by default. For a frequently used destination, also select [Favorites]. If [Favorites] is selected, the destination will appear in the main screen of the fax/scan mode, enabling the user to easily select a destination.
[Fax Number]	Enter a destination fax number. When you use this machine in a PBX environment, tap [Outside] ([E-] appears). A registered outside line number is automatically inserted. When you use this machine in a PBX environment, press [Pause] following the outside line number ([P] appears) to ensure the dialing. If you want to send out a push signal over the dial line, tap [Tone] ([T] appears). Press [-] to separate a dial number. This does not affect the dialing of the number.
[Line Settings]	As necessary, specify how to send a fax to a destination you want to register. You can change the settings you made here before sending a fax. [Overseas TX]: Used to send a fax to areas where communication conditions are poor. Faxes are sent at a lower speed. [ECM OFF]: Generally, faxes are sent while checking that the fax data is free of errors by using ECM (Error Correction Mode). To reduce the time required to send a fax, tap [ECM OFF]. [V34 OFF]: Generally, faxes are sent in the Super G3 mode. If it is not possible to send faxes in the Super G3 mode, tap [V34 OFF]. [Check Dest. & Send]: When using the Check Dest. & Send function, select [Yes]. The fax number specified for fax is checked against the re-mote fax number (CSI) and the fax is only sent when they match. [Select Line]: If two lines are used, select the line used to send a fax. If [Unset] is selected, either line, whichever is not busy, is used for transmission.

Select whether to display the screen indicating the machine status during fax transmission.

Settings	Description
[TX Display]	Select whether to display a screen indicating a fax being sent. You can check information on a destination and document in this screen. [No] is specified by default.
[RX Display]	Select whether to display a screen indicating a fax being received. You can check information on sender and fax being received in this screen. [No] is specified by default.

Select whether to display finishing program keys in the main screen of the copy mode.By arranging a frequently used finishing setting to the finishing program, you can specify the finishing setting only by tapping the program key in the main screen of the copy mode.

Register destination FTP server host names or IP addresses.

Settings	Description
[No.]	Destination registration number. [No.] is automatically registered using an unused smaller number. If you want to specify a number, tap [No.] and enter the number within the range of 1 to 2000.
[Name]	Enter the destination name to be displayed on the Touch Panel (using up to 24 characters). Assign a name that helps you easily identify the destination.
[Sort Character]	Enter the same name as the registered name (using up to 24 characters). You can sort destinations by registration name.
[Index]	Select a corresponding character so that the destination can be index-searched by registration name. If an alphabet character is specified for the initial of a registration name, search text is automatically specified with the alphabet character. If anything other than alphabet character is specified for the initial of a registration name, [etc] is specified by default. For a frequently used destination, also select [Favorites]. If [Favorites] is selected, the destination will appear in the main screen in fax/scan mode, enabling the user to easily select a destination.
[Host Address]	Enter the host name or IP address of the destination FTP server with up to 63 bytes. Host name entry example: "host.example.com" Example of IP address (IPv4) entry: "192.168.1.1" Example of IP address (IPv6) entry: "fe80::220:6bff:fe10:2f16"
[File Path]	Enter the name of a destination folder in the FTP server specified in [Host Address] with up to 127 bytes. Entry example: "scan" When not specifying a file path, enter a slash "/".
[User ID]	If authentication is required in the destination FTP server, enter the login-enabled user name (using up to 64 characters).
[Password]	Enter the password of the user specified in [User ID].
[anonymous]	When authentication is not required for the destination FTP server, press [ON]. [OFF] is specified by default.
[PASV]	When the PASV mode is used in your environment, press [ON]. [OFF] is specified by default.
[Proxy]	When a proxy server is used in your environment, press [ON]. [OFF] is specified by default.
[Port Number]	If necessary, change the port number. In normal circumstances, you can use the original port number. [21] is specified by default.

Change the function key to be displayed in the main screen in the copy mode and the print settings screen in the User Box mode.Select a function key number, and specify the function to assign.

Change the function key to be displayed in the main screen in fax/scan mode and the send and save settings screens in User Box mode.Select a function key number, and specify the function to assign.