[SNMP Setting]

When enabling SNMP, set this option to ON (default: ON).

• [SNMP v1/v2c(IP)]: When using SNMP v1 or SNMP v2, set this option to ON (default: ON).

• [SNMP v3(IP)]: When using SNMP v3, set this option to ON (default: ON).

[UDP Port Setting]

If necessary, change the UDP port number (default: [161]).

[SNMP v1/v2c Setting]

Configure SNMP v1/v2c settings.

• [Read Community Name]: Enter a read-only community name (using 1 to 15 single-byte characters, excluding spaces, \, ', ", and #) (default: [public]).

• [Write Community Name]: When allowing reading and writing, set this option to ON (default: ON). Also enter a community name used for reading and writing (using 1 to 15 single-byte characters, excluding spaces, \, ', ", and #) (default: [private]).

[SNMP v3 Setting]

Configure SNMP v3 settings.

• [Context Name]: Enter the context name (using up to 63 single-byte characters, excluding spaces, \, ', ", and #).

• [Discovery User Name]: When allowing the detection user, set this option to ON (default: ON). Also, enter a user name for detection (using 1 to 32 single-byte characters, excluding spaces, \, ', ", and #) (default: [public]).

• [Read User Name]: Enter a read-only user name (using up to 32 single-byte characters, excluding spaces, \, ', ", and #) (default: [initial]).
  [Security Level]: Select a security level of the user in the read-write enable state (default: [auth-password/priv-password]).
  [auth-password]: If [auth-password] or [auth-password/priv-password] is selected from [Security Level], enter an authentication password for the read-only user (using 8 to 32 single-byte characters, excluding spaces, \, ', ", and #).
  [priv-password]: If [auth-password/priv-password] is selected from [Security Level], enter a password used for privacy (encryption) of the read-only user (using 8 to 32 single-byte characters, excluding spaces, \, ', ", and #).

• [Write User Name]: Enter the user name of the user in the read-write enable state (using up to 32 single-byte characters) (default: [restrict]).
  [Security Level]: Select a security level of the user in the read-write enable state (default: [auth-password/priv-password]).
  [auth-password]: If [auth-password] or [auth-password/priv-password] is selected from [Security Level], enter an authentication password for the read-write enabled user (using 8 to 32 single-byte characters, excluding spaces, \, ', ", and #) (default: MAC address of this machine (Alphabetic characters are all in capitals, excluding colons ":")).
  [priv-password]: If [auth-password/priv-password] is selected from [Security Level], enter a password used for privacy (encryption) of the read-write enabled user (using 8 to 32 single-byte characters, excluding spaces, \, ', ", and #) (default: MAC address of this machine (Alphabetic characters are all in capitals, excluding colons ":")).

• [Encryption Algorithm]: Select an encryption algorithm (default: [DES]).

• [Authentication Method]: Select an authentication algorithm (default: [SHA-256]).

[TRAP function]

Configure settings for the SNMP TRAP function.

• [Permit Access]: When allowing a notification of the status of this machine using the SNMP TRAP function, set this option to ON (default: ON).

• [Send TRAP TX if authentication fails]: When performing TRAP TX due to an authentication failure, set this option to ON (default: OFF).

[Administrator Information]

Enter information of this machine.

• [Device Name]: Enter the name (MIB sysName) of this machine (using up to 255 single-byte characters).

• [Device Location]: Enter the location where to install this machine (MIB sysLocation) (using up to 255 single-byte characters).

• [Administrator Name]: Enter the administrator name (MIB sysContact) (using up to 255 single-byte characters).

[Notification Address]

Enter the E-mail address of the destination (using up to 253 single-byte characters). Use one of the following formats.
Example to enter the host name: "host.example.com"
Example to enter the IP address (IPv4): "192.168.1.1"
Example to enter the IP address (IPv6): "fe80::220:6b.:fe10:2f16"

[Port No.]

If necessary, change the port number.

[Community Name]

Enter the community name (using up to 15 single-byte characters) (default: [public]).

[Alert]

Select items to be notified automatically. Select the check boxes of items to be notified.