- Home
- Menu
× Menu Useful Software If you have a problem…
- FAQ
- Troubleshooting
Menu
Adjustments
- Function Overview
- Function Overview
- Adjustment Menu
- Quality Adjustment
- Machine Adjustment
- Stabilization Adj. Setting
- Execute Adjust Operation
- Finisher Adjustment
- Staple Finisher(Main) Adj. (Finisher FS-532)
- Staple Finisher(Fold) Adj. (Finisher FS-532)
- Staple Finisher(Punch) Adj. (Finisher FS-532)
- Staple Finisher(PI) Adj. (Finisher FS-532)
- Staple Finisher(Main) Adj. (Output Tray OT-510)
- Multi Folder(Punch) Adj. (Folding Unit FD-503)
- Multi Folder(Fold) Adj. (Folding Unit FD-503)
- Stacker Adjustment (Large Capacity Stacker LS-506)
- Saddle Stitcher Adjustment (Saddle Stitcher SD-506)
- Saddle Stitcher Adjustment (Saddle Stitcher SD-513)
- Fold Paper Width Adj.
- Fold Skew Adjustment
- Half-Fold Position Adj.
- Tri-Fold Position Adj.
- Crease Position Adjustment
- Staple Paper Width Adj.
- Staple Center Position
- Staple Pitch Adjustment
- Staple Offset Adjustment
- Staple Tip Adjustment
- Flattening a Fold (Strength)
- Flattening a Fold (Freq.)
- Parallel Trimming Adjustment
- Fore-edge Trimming Adj.
- 2-Side Slitting Adjustment
- 2-Side Slit Finishing Adj.
- Trimmer Receiver Adj.
- Perfect Binder Adjustment (Perfect Binder PB-503)
- Finisher Adjustment (Finisher FS-531 / Finisher FS-612)
- Relay Stacker Adjustment (Relay Unit RU-510)
- ADF Adjustment
- PFU Air Assist Adjustment
- IQ Detected Result
- IQ Function Setting
- Memory Status
- Both Sides Adjust
- Adjusting the Finishing
- Image Quality
- About Image Quality
- Controller Calibration
- Advanced Controller Calibration (Exact Color)
- Advanced Controller Calibration (G7)
- Registering an Output Profile
- Spot Color Information
- Alternative Color (Replacing RGB with CMYK)
- Alternative Color (Replacing CMYK with CMYK)
- Adjusting Tone Curves
- Registering the Color Configuration
- Changing the Screen
- Adjusting the Margin between Pages
- Adjusting the Staple Positions
- Adjusting Misalignment or Tilt of the Punch Hole Positions
- Adjusting the Half-Fold Position of a Booklet
- Adjusting Misalignment, Skew, and Protrusion of a Perfect-Bound Book
- Adjusting the Folding Positions
- Image Quality
Main ScanDir.Zoom Auto(Back)
Automatically adjust the magnification in crosswise direction on the back side when scanning on the ADF.
Press Adjustment on the MACHINE screen to display the Adjustment Menu screen.
Press ADF Adjustment and Main ScanDir.Zoom Auto(Back) in sequence.
Place the test chart on the ADF tray, and press Start.
supplementary explanationFace the test chart surface downward and place it in the ADF tray.
Automatic adjustment is performed, and its result is displayed.
supplementary explanationIf it ends successfully, Adjustment Result indicates OK. If it ends abnormally, NG is displayed. Adjust it using the Main Scan Dir. Zoom(Back).
Make sure that the adjustment result is OK, and press Set.
supplementary explanationThe Zoom Adj.(%) value is reflected on Current Data.
Press Return.
The screen returns to the ADF Adjustment Menu screen.