Home Search by Purpose Managing the Power Supply for Power Saving (For Administrators)

Search by Purpose

Managing the Power Supply for Power Saving (For Administrators)

To change the time required to automatically shift to the sleep mode ([Sleep Mode Settings])

To display:
  • [Utility]
    • [Administrator Settings]
      • [System Settings]
        • [Power Supply/Power Save Settings]
          • [Sleep Mode Settings]

Change the time required to automatically change to the Sleep mode after you did not operate this machine.

Sleep mode provides a greater power saving effect than the Low Power mode. However, the time required to return to the normal mode is longer than the time required to recover from the Low Power mode.

The default is [30] min. (allowable range: [15] to [240] min.).

To change the time required to automatically shift to the low power mode ([Low Power Mode Settings])

To display:
  • [Utility]
    • [Administrator Settings]
      • [System Settings]
        • [Power Supply/Power Save Settings]
          • [Low Power Mode Settings]

Change the time required to automatically change to the Low Power mode after you did not operate this machine.

In the Low Power mode, the display of the Touch Panel is turned off to reduce power consumption.

The default is [15] min. (allowable range: [10] to [240] min.).

To change the operation to be performed when the Power key has been pressed ([Power Key Setting])

To display:
  • [Utility]
    • [Administrator Settings]
      • [System Settings]
        • [Power Supply/Power Save Settings]
          • [Power Key Setting]

Select whether to use the Power key on the Control Panel as a sub power OFF key or as a power save key.

Settings

Description

[Sub Power OFF]

Press the Power key briefly to turn the sub power off. If the Power key is held down, the power save mode is switched to the ErP Auto Power Off mode (similar to main power off mode), which provides a higher power saving effect than when the sub power is turned off.

[Power Save]

Press the Power key briefly to turn the power save mode on (Low Power or Sleep mode). Hold down the Power key to turn the sub power off.

[Power Save] is specified by default.

To specify the operation required to use the Power key as a power save key ([Power Save Settings])

To display:
  • [Utility]
    • [Administrator Settings]
      • [System Settings]
        • [Power Supply/Power Save Settings]
          • [Power Save Settings]

When using this machine in the factory default status, choose this setting to select the type of the power save mode when pressing the Power key on the Control Panel.

Settings

Description

[Low Power]

Switches to the Low Power mode. Turns off the display of the Touch Panel to reduce power use.

[Low Power] is specified by default.

[Sleep]

Switches to the Sleep mode. Sleep mode provides a greater power saving effect than the Low Power mode. However, the time required to return to the normal mode is longer than the time required to recover from the Low Power mode.

To specify whether to return to the power save mode earlier than normal after printing in the power save or sleep mode ([Enter Power Save Mode])

To display:
  • [Utility]
    • [Administrator Settings]
      • [System Settings]
        • [Power Supply/Power Save Settings]
          • [Enter Power Save Mode]

When this machine receives a print job from a fax machine or computer in the Power Save mode, select the timing to switch to the Power Save mode after the print job has ended.

Settings

Description

[Normal]

Switches based on the time specified in [Low Power Mode Settings] and [Sleep Mode Settings].

[Immediately]

Switches to the Power Save mode immediately after a print job has ended.

[Immediately] is specified by default.

To specify whether to reduce power consumption in the sleep mode ([Power Consumption in Sleep Mode])

To display:
  • [Utility]
    • [Administrator Settings]
      • [System Settings]
        • [Power Supply/Power Save Settings]
          • [Power Consumption in Sleep Mode]

Select whether to reduce the power consumption in the Sleep mode.

Settings

Description

[Enabled]

Further reduces the power consumption in the Sleep mode. Select [Enabled] in normal conditions.

[Enabled] is specified by default.

[Disabled]

Select this option when a smooth network communication is not established while [Enabled] is specified.

To reduce power consumption when returning from the power save mode to a mode other than the copy mode ([Power Saving Fax/Scan])

To display:
  • [Utility]
    • [Administrator Settings]
      • [System Settings]
        • [Power Supply/Power Save Settings]
          • [Power Saving Fax/Scan]

Select whether to give priority to the power saving when returning from the Sleep or sub power off mode to a mode other than the copy mode.

When returning to a mode that does not involve printing, such as scan/fax mode, power consumption can be reduced by not adjusting the temperature of the Fusing Unit on this machine.

You can set this option when you have selected an option other than [Copy] in [Priority Mode] that is selected by [Administrator Settings] - [System Settings] - [Reset Settings] - [System Auto Reset].

Settings

Description

[Power Save]

The temperature of Fusing Unit is not adjusted when the machine returns to the normal mode.

[Standard]

The temperature of Fusing Unit is adjusted when the machine returns to the normal mode.

[Standard] is specified by default.

To specify whether to return from Low Power mode or Sleep mode to the normal mode without touching the touch panel ([Awake from Power Save Mode by Touching Control Panel])

To display:
  • [Utility]
    • [Administrator Settings]
      • [System Settings]
        • [Power Supply/Power Save Settings]
          • [Awake from Power Save Mode by Touching Control Panel]

When Low Power mode or Sleep mode has been established: if hands or man get closer to Touch Panel, you can select whether to restore or not from Low Power mode or Sleep mode.

If you select [ON], you can adjust the sensitivity of the sensor. Making a setting on the minus side decreases the sensitivity (shortens the sensing distance). Making a setting on the positive side increases the sensitivity (lengthens the sensing distance).

The default is set to [ON], and the adjustment value to [0].

To use the weekly timer for automatic switching between normal and power save modes ([Weekly Timer ON/OFF Settings])

To display:
  • [Utility]
    • [Administrator Settings]
      • [System Settings]
        • [Weekly Timer Settings]
          • [Weekly Timer ON/OFF Settings]

Specify whether to use the weekly timer. Then, select a power save mode for the machine to enter according to the weekly timer.

Settings

Description

[ON]/[OFF]

Specify whether to use the weekly timer.

[ON] is specified by default.

[Power Save Mode Setting]

Select a power save mode to which the machine enters based on the weekly timer.

  • [ErP Auto Power OFF]: A mode that provides a higher more effective power saving effect. In this mode, you cannot receive all jobs.

  • [Sleep]: This mode has a lower power saving effect than the [ErP Auto Power OFF] mode; however, it allows you to receive print jobs from a fax machine or computer. The received jobs are printed when the machine returns to the normal mode.

[Sleep] is specified by default.

To set the time to the weekly timer ([Time Settings])

To display:
  • [Utility]
    • [Administrator Settings]
      • [System Settings]
        • [Weekly Timer Settings]
          • [Time Settings]

Specify the time for switching to the power save mode ([OFF Time]) and the time for returning to the normal mode ([ON Time]) for each day of the week.

  • [Set All]: Select days of the week and specify times for [ON Time] and [OFF Time] for all the selected days.

  • [Delete]: Deletes the time you have selected by using[][].

To set the date to the weekly timer ([Date Settings])

To display:
  • [Utility]
    • [Administrator Settings]
      • [System Settings]
        • [Weekly Timer Settings]
          • [Date Settings]

Configure the day to which the weekly timer is applied.

Select the day to which the weekly timer is applied by switching the calendar by [Year] and [Monthly]. Optionally, you can collectively configure the appropriate days for each day of the week with [Daily Setting].

To specify the time zone to temporarily shift to the sleep mode during lunch break ([Select Time for Power Save])

To display:
  • [Utility]
    • [Administrator Settings]
      • [System Settings]
        • [Weekly Timer Settings]
          • [Select Time for Power Save]

Specify whether to set a time zone for switching the machine in the normal mode with the weekly timer enabled temporarily to the sleep mode during lunch time, for example.

If you select [Yes], specify the time zone for switching to the sleep mode.

  • [Power Save Start Time]: Specify the time for the machine to enter the sleep mode.

  • [Power Save End Time]: Specify the time for the machine to return to the normal mode.

[OFF] is specified by default.

To restrict the use of this machine with a password while the weekly timer is active ([Password for Non-Business Hours])

To display:
  • [Utility]
    • [Administrator Settings]
      • [System Settings]
        • [Weekly Timer Settings]
          • [Password for Non-Business Hours]

Specify whether to restrict the use of this machine in the Power Save mode by requesting a password.

To request a password in order to restrict operation, enter the password for a user to enter (using up to eight characters).

[No] is specified by default.

To automatically configure a weekly timer schedule depending on operation conditions ([Tracking Function Settings])

To display:
  • [Utility]
    • [Administrator Settings]
      • [System Settings]
        • [Weekly Timer Settings]
          • [Tracking Function Settings]

Specify whether to use the tracking (learning) function that automatically sets the weekly timer schedule to fit the operating status of your office.

To use the tracking function, select [Auto Standby Adjustment Level] to specify the level at which it is judged that this machine is inactive. The higher the level is, the more easily this machine is judged as inactive, resulting in setting of a longer OFF time.

[ON] is specified by default.

To confirm the weekly timer schedule configured by the tracking function ([Display ON/OFF Time])

To display:
  • [Utility]
    • [Administrator Settings]
      • [System Settings]
        • [Weekly Timer Settings]
          • [Display ON/OFF Time]

Displays the switching times to enter the power save mode ([OFF Time]) and to the normal mode ([ON Time]) set by the tracking function.

Tap the [Clear Usage Data] to delete data related to the usage status of this machine and reset the values for [OFF Time] and [ON Time] that have been automatically set.