Adjust the AE (Auto Exposure) level (default: ).
Adjust in five levels. The larger the number, the darker the background.
Adjust the print start position and defective print images.
[Leading Edge Adjustment]
[Leading Edge Adjustment (Duplex Side 2)]
[Centering (Duplex 2nd Side)]
[Erase Leading Edge]
Correct the misalignment or tilt of scanning area caused by changes in the temperature or humidity in the machine to ensure high quality printing.
[Image Stabilization Only]
Select the image stabilization method (default: [Image Stabilization Only]). Select [Start] to execute the image stabilization process.
[Image Stabilization Setting]
Change the timing for executing image stabilization as well as the type of image stabilization, as required. Make selection according to the printing frequency and the color/black use ratio (default: [Standard]).
Adjust the paper separation position on each side of paper for 2-sided printing.
Adjust balance between the properties related to paper separation and image transfer when paper jams are occurring or images are defective due to the environment being overly hot or humid.
Select the paper and side on which to adjust the paper separation.
Enter the adjustment value between -10.0 mm and 10.0 mm (default: [0.0 mm]).
Increase the value if paper jams are occurring, and reduce it if the image is transferred unevenly.
Adjust the print position for each paper type with respect to each color if color shifts are detected in the print result.
Load paper into the Bypass Tray and tap the [Adjust automatically] key to start printing the test pattern. Make adjustments while checking the test pattern. Repeat adjustments as necessary.
The example shows the color registration adjustment for cyan.
If the print position of the desired color is out of line to the left or right with respect to the printing position of black, enter an adjustment value in the range between -6 dots and +6 dots (default: [0 dot]).
Increase the value when moving the printing position rightward, and reduce it when moving the printing position leftward.
If the print position of the desired color is out of line vertically with respect to the printing position of black, enter an adjustment value in the range between -6 dots and +6 dots (default: [0 dot]).
Increase the value when moving the printing position upward, and reduce it when moving the printing position downward.
Restart this machine.
Check that [Image Stabilization Only] is selected in [Expert Adjustment] - [Gradation Adjustment] and then use the Start key to start the image stabilization.
The image stabilization operation starts. Now adjustment items on the right are available for selection.
Select items to be adjusted.
[Printer (600dpi)]: Select this option when the image printed with resolution 600 dpi has irregular gradation.
[Print (1200dpi) Gradation]: Select this option when the image printed with resolution 1200 dpi has irregular gradation.
[Print (1200dpi) Resolution]: Select this option when the image printed with resolution 1200 dpi has irregular resolution.
[Copy]: Select this option when a copied image has irregular gradation.
Select a paper type for printing a test pattern.
Bypass Tray cannot be selected.
Use the Start key to start printing a test pattern.
Place the test pattern on the Original Glass based on the orientation displayed on the screen.
Place ten or more blank sheets of paper to prevent bleeding of the test pattern.
Close the ADF.
Use the Start key to start scanning a test pattern.
The gradation level is adjusted automatically.
Repeat steps 3 to 9 twice. (Total of three times)
Adjust the scan range of the scanner. For details, contact your service representative.
Make adjustments for scanning images in the ADF. For details, contact your service representative.
Register special paper with [User Paper 1] through [User Paper 6]. Configure setting for the basic weight and media adjustment.
For details, contact your service representative.
Specify the operation of [Non-Image Area Erase] that is available in copy mode of classic style.
Select either the option for erasing the non-image area by the optimal method automatically selected for the background density of the original or the option for erasing by the pre-specified method (default: [Specify]).
Select an erase method after selecting [Specify] for [Erase Operation].
Adjust the density of the original.
When outputting CMYK data without using the simulation profile, set this option to ON (default: OFF). This option is available when [Simulation Profile] for the PS driver is set to [Auto].
Selecting OFF uses a simulation profile based on your processing to correct an entered image with the same density as when an image is output using the PCL driver.
You can specify the default setting for a simulation profile to be displayed on the printer driver. For details on the setting procedure, refer to Here.