Adjusting Standards
Combination of Implementation Timing and Adjustment Items
This section describes the basic color adjustment processes that should be performed first.
The adjustment items may differ depending on the options mounted on the system.
Recommended Settings (With Intelligent Quality Care Unit IQ-501 Mounted)
1
Configure the following settings on [Color Density Control] - [Basic Setting]. The system automatically determines the timing at which Periodical Adjustment (automatic adjustment) is performed.
- Set [Use Color Density Control] to [ON]
- Set [Periodical Adj. Execution] to [ON]
- Set [Adjustment Execution Timing] to [During Job Runs]
- Set [Adjustment Interval] to [ON]: 1,000 sheets
When the periodic adjustment is set, manual adjustment is not required; however, if you want to update the adjustment value according to the work conditions, perform [Color Density Manual Control]. For details, refer to section 4 in "Recommended Settings".
2
Set [Synchronize with Image Diagnosis (AQA)] to [ON] with [Package Color Auto Adj.]. You can collectively adjust the items related to the image stability.
It is recommended to perform [Package Color Auto Adj.] at least once per day.
With [Synchronize with Image Diagnosis (AQA)], you can select the items for adjustment to be performed automatically after performing [Image Diagnosis].
For details about [Image Diagnosis], refer to [Image Diagnosis].
3
When sending a job, configure the following settings in advance for making adjustments on a job by job basis.
- Set [Quality] - [Auto Image Adjustment] to [Position/Gradation]
The Auto Image Adjustment function adjusts the image quality in real time during printing, thereby, resulting in improvement of image stability. For details, refer to To Perform Auto Image Adjustment.
4
To make adjustments at any time other than when the periodic adjustment takes place, perform [Color Density Manual Control] (manual adjustment).
Manual adjustment is recommended in the following cases.
- Color variation is noticeable for some reason
- Before mass printing
- Before printing when color is important
Recommended Settings (With Intelligent Quality Care Unit IQ-501 Unmounted and Relay Unit RU-518m Mounted)
1
Configure the following settings on [Color Density Control] - [Basic Setting]. The system automatically determines the timing at which Periodical Adjustment (automatic adjustment) is performed.
- Set [Use Color Density Control] to [ON]
- Set [Periodical Adj. Execution] to [ON]
- Set [Adjustment Execution Timing] to [During Job Runs]
- Set [Switch Color(1st or 2nd)] to [Precise]
- Set [Adjustment Interval] to [ON]: 1,000 sheets
When the periodic adjustment is set, manual adjustment is not required; however, if you want to update the adjustment value according to the work conditions, perform [Color Density Manual Control]. For details, refer to section 2 in "Recommended Settings".
2
To make adjustments at any time other than when the periodic adjustment takes place, perform [Color Density Manual Control] (manual adjustment).
Manual adjustment is recommended in the following cases.
- Color variation is noticeable for some reason
- Before mass printing
- Before printing when color is important
3
Perform the following adjustments once every 3 months for maintenance.
- [Gamma Automatic Adjustment]
- [Max. Density Auto Adj.] (Perform using the same paper as when registering)
- [Color Density Control] (Perform using the specified paper)
- [Exact Color] / [G7] (Perform using the specified paper)
Recommended Settings (With Intelligent Quality Care Unit IQ-501 Unmounted and Relay Unit RU-518m Unmounted)
1
Perform [Controller Calibration].
For details about [Controller Calibration], refer to About Normal [Controller Calibration].
2
Perform the following adjustments once every 3 months for maintenance.
- [Gamma Automatic Adjustment]
- [Maximum Density Adjustment] (Perform using the specified paper)
- [Controller Calibration] (Perform using the specified paper)
- [Exact Color] / [G7] (Perform using the specified paper)
For details about [Controller Calibration], refer to About Normal [Controller Calibration].
in the upper-right of a page, it turns into 
and is registered as a bookmark.