Menu Items (without Paper Feed Unit PF-711 Mounted)

User Setting: System Setting

Menu Item/Description

Setting Items/Options (with default bolded)

01 Language Setting

Select the language used in the touch panel and voice messages.

Language Used in LCD: Japanese, Hangul

Taiwan, Chinese

English, French, German, Italian, Spanish

Language in Voice Message: English, Japanese, OFF

02 Unit Setting

Select the unit of measurement for numeric values to be displayed on the touch panel.

mm, Inch (Decimal Point), Inch (Fraction)

03 Paper Tray Setting

01 Paper Setting

01 Paper Profile Setting

Register or delete the paper settings. Up to 500 can be registered.

Paper Type, Profile Name, Paper Size, Weight, Colored Paper, Punch, Both Sides Adjust, RU Curl Adjustment, Air Assist, Thickness *1, Expert Adjustment *2, Color Density Control

Import, Export

*1: Thickness is displayed when Image Controller IC-604 is mounted.

*2: Expert Adjustment is not displayed by default. Contact your service representative.

02 Preset Profile Management

Allows you to add or delete a profile.

Profile search

Preset profile import to USB memory, profile deletion, profile addition

Paper profile deletion

02 Auto Tray Selection Setting

Select the tray to take over the feeding when the tray currently used becomes out of paper. This function is called Auto Tray Switch (ATS). When selecting multiple trays for ATS, determine the priority of the trays.

ATS/APS Switch: Tray1 to Tray9

Tray Priority: Order of priority for selected trays

03 Type for Auto Paper

Specify paper conditions that enable a tray to be selected in Auto Paper (APS).

Paper conditions to be specified here are Paper Type, Weight, Punch, Tab Paper, and Colored Paper.

Paper Type: Plain, Fine, Color Specific, Coated-GL, Coated-ML, Coated-GO, Coated-MO

Weight:52-61g/m2 / 14-15 lb Bond, 62-74 g/m2 / 16-19 lb Bond, 75-80 g/m2 / 20-21 lb Bond, 81-91 g/m2 / 22-24 lb Bond, 92-105g/m2 / 25-28 lb Bond, 106-135g/m2 / 29-36 lb Bond, 136-176g/m2 / 37-47 lb Bond, 177-216g/m2 / 48-57 lb Bond, 217-256g/m2 / 58-68 lb Bond, 257-300g/m2 / 69-81 lb Bond, 301-350g/m2 / 82-93 lb Bond, 351-400g/m2 / 94-106 lb Bond

Punch: Allow, Restrict

Tab Paper: Allow, Restrict

Colored Paper: White, Blue, Goldenrod, Gray, Green, Ivory, Orange, Pink, Red, Yellow, Cream, Others, User Color

04 Dehumidify Fan Heater

Set the operating conditions of the dehumidifying fan heater installed in the paper feeder unit (trays 1 to 9).

Dryness Preparation: ON, OFF

Fan Heater Control (Trays 1 to 9): Auto, Compulsively ON, Compulsively OFF

04 Reset Setting

01 Auto Reset Setting

The screen selected as the default screen returns after a certain period of inactivity. Select the time interval to activate this function.

OFF, 60 seconds, 120 seconds, 180 seconds, 240 seconds, 300 seconds, 360 seconds, 420 seconds, 480 seconds, 540 seconds

05 Default Screen Setting

Select the screen to be displayed when the sub power switch is turned on or Auto Reset is activated.

MACHINE, JOB LIST/Hold Job, JOB LIST/Reserved Job

06 Power Save Setting

01 Power Save Function Setting
Select the time to activate Auto Low Power and Auto Shut OFF. Also select either Auto Low Power or Auto Shut OFF to be activated when Power Save is pressed on the control panel.

You can also select the condition of Auto Wake-up to activate the machine when a print job is received during Auto Shut OFF.

Auto Low Power: --- min., 5 min., 10 min., 15 min., 30 min., 60 min., 90 min., 120 min., 240 min.
Auto Shut OFF: --- min., 0 min., 1 min., 30 min., 60 min., 90 min., 120 min., 240 min.
Power Save Function: Auto Low Power, Auto Shut OFF

Auto Wake-up Cond.: All Jobs

02 ErP Setting

Automatically turn off the main power switch when the sub power switch is turned off, or when Auto Shut OFF or Auto Low Power has been active for a certain time.

Do Not Switch, 12 Hours, 24 Hours, 36 Hours, 48 Hours, 60 Hours, 72 Hours

03 Mono Energy-save Mode

Set whether to run Monochrome printing in energy-save mode.

ON, OFF

07 Date/Time Setting

Set the current date and time, the daylight-saving time, and the time difference.

Setting Time

Daylight Saving Time: OFF, ON (1 to 150 min.)

Time Zone

08 Operation/Info. Sound Setting

01 Volume Setting

Specify whether to turn the operation sound and speaker sound on or off, and also set the volume when they are turned on.

Operation Sound: ON, OFF,

1 (Small) to 8 (Big)

Speaker sound: ON, OFF; 1 (Small) to 10 (Big)

02 Info. Sound Item Setting

Specify each items provided for information sound and voice message.

Repeat Number Setting

Info. Sound Repeat Number: 1 time, 2 times, 3 times

Voice Repeat Number: 1 time, 2 times, 3 times

Notice Set for Machine Stop

Paper JAM: Voice, Info. Sound, OFF

Paper Empty: Voice, Info. Sound, OFF

Paper Differ: Voice, Info. Sound, OFF

Replenish Toner: Voice, Info. Sound, OFF

Service Call: Info. Sound, OFF

Output full: Info. Sound, OFF

Other Notification Setting

Job Complete Pre-notice: Voice, OFF

Stop Button Acceptance: Voice, OFF

Sample Print Completion: Voice, OFF

Finisher Front Door Alert: Voice, OFF

Other Info. Sound Setting

For System Starting: Info. Sound, OFF

For Sample Printing: Info. Sound, OFF

For Print Job Receiving: Info. Sound, OFF

09 Key Response Time

Select the time interval to get the response from the machine when a key is pressed on the touch panel.

Normal, 0.5 seconds, 1 second, 2 seconds, 3 seconds

10 Service Port Device Setting

Specify whether or not to use a service port device, and select the keyboard type if the service port device is used.

Service Port Device: ON, OFF

Keyboard Type: EN65, EN104, JP101, JP106, JP109

11 Mouse Setting

Select whether or not to use the Wheel Booster function and Cursor Auto Scrolling function, respectively, for when the mouse is connected.

Wheel Booster Setting: ON, OFF

When using this function, set List Scrolling Speed and Value Scrolling Speed.

Cursor Auto Scrolling Set.: ON, OFF

When using this function, set cursor speed, cancel sensitivity, and cursor prior return position, and cursor prior destination.

User Setting: Common Setting

Menu Item/Description

Setting Items/Options (with default bolded)

One Shot Message Indication Time

Select the time span to display a shot message in the message area of the touch panel.

3 seconds, 5 seconds

Offset by Job Unit

Specify whether or not to offset the output sheets by job. Also specify the number of jobs to be offset when selecting ON for this function.

ON, OFF (Selecting ON: Offset Job Number, Initial Value: 1)

Continuation Print

Specify whether or not to output multiple reserve jobs in succession without stopping the machine at a job break.

Printer ON, Printer OFF

Back Side Magnification Adjustment

Select whether or not to activate the back side magnification adjustment mode.

ON, OFF

Fusing Stability (Mixed Media)

Select what to prioritize when fusing.

Best Quality, Better Quality, Speed, Highest Speed

Prior Paper Type

Specify the temperature setting of the fusing section on standby. It can shorten the waiting time before printing by selecting a frequently used paper.

Others, Coated

Dash Length(Page Stamp)

Select the length of the dash to be used in a style of Page No. in Stamp.

Long, Short

Center Crop Mark Trim Margin

Specify the space between the center crop mark and image area (center crop mark trim margin).

0.0 mm to 20.0 mm (Default: 1.0)

Schedule Cross Axis Unit (Default)

Select the unit of horizontal axis on the Schedule screen.

Timetable, Time Frame (m), Sheet Volume

Hold Job Status after Output (Default)

Select the default value to delete or save the data of hold job after outputting.

Delete, Save

Offset Output Mode

Specify how to offset the output sets.

Change Out Pos., Stop Print, Change Out Position + Partition Paper (Tray1 to Tray9, PI 1, PI 2), Partition Paper (Tray1 to Tray9, PI 1, PI 2)

Hold Job Direct Output (Default)

Select the default for the Direct Output check box under the Hold Job screen.

ON selects the check box, and OFF clears the check box.

After the change, turn OFF/ON the sub power switch to apply the setting.

ON, OFF

Needless Tab Paper Exit

Specify whether or not to automatically discharge the oddments of tabbed sheets loaded in a tray as a set for copy job.

ON, OFF

Remaining Memory (Measurement Unit)

Select the unit of displaying the remaining memory.

%, GB

Remaining Memory (Warning)

Select the percentage at which to give warning when the remaining memory is low.

5% or Less, 10% or Less

[Proof Copy] 1 Set/1st Sheet Selection

If it is turned ON, the confirmation window is opened and you are asked to output one confirmation copy or to output only its first page when the Proof Copy is pressed.

ON, OFF

Both Sides Rotate/Skew

If Disable is selected, the Rotate/Skew adjustment does not become available and does not function.

Enable, Disable

Auto Image Adjustment Deviation Check

Select whether to automatically check a deviation. If you select ON, enter the specified value of a deviation.

ON (ON: 0.5 mm to 10.0 mm, Default: 2.0), OFF

Operation after Deviation Detected

Select how to perform operations when a deviation is detected. If you select Continue Output, select the paper tray to output data to and the number of deviation detection times.

Stop, Continue Output, Partition Paper (Tray1 to Tray9), Detection Count (2 to 10 times, Default: 2)

Select Chart Type (Auto Image Adj.)

Select an automatic image adjustment chart for each paper weight.

Type1, Type2

User Setting: Printer Setting

Menu Item/Description

Setting Items/Options (with default bolded)

01 Outline Process

Select the Outline Process for printing.

Text Thinning: Weak+, Weak, Normal, Strong, Strong+

Halftone Text Enhancement: Weak+, Normal, Strong+, Strong(+1), Strong(+2)

FD Lead Edge Density Adjustment: 0 to +5

FD Rear Edge Density Adjustment: -5 to 0

02 Select Prior Output Tray

Select the output tray for the jobs for which the output tray is specified as "Auto". This menu item is to be displayed and allowed on the machine mounted with Finisher FS-532.

Main Tray, Sub Tray

User Setting: Change Password

Change the user password previously registered with user authentication. This function is available when user authentication is enabled.

Administrator Setting: System Setting

Menu Item/Description

Setting Items/Options (with default bolded)

01 Power Save Setting

01 Power Save Function Setting
Select the time to activate Auto Low Power and Auto Shut OFF. Also select either Auto Low Power or Auto Shut OFF to be activated when Power Save is pressed on the control panel.

You can also select the condition of Auto Wake-up to activate the machine when a print job is received during Auto Shut OFF.

Auto Low Power: --- min., 5 min., 10 min., 15 min., 30 min., 60 min., 90 min., 120 min., 240 min.

Auto Shut OFF: --- min., 0 min., 1 min., 30 min., 60 min., 90 min., 120 min., 240 min.

Power Save Function: Auto Low Power, Auto Shut OFF

Auto Wake-up Cond.: All Jobs

02 ErP Setting

Automatically turn off the main power switch when the sub power switch is turned off, or when Auto Shut OFF or Auto Low Power has been active for a certain time.

Do Not Switch, 12 Hours, 24 Hours, 36 Hours, 48 Hours, 60 Hours, 72 Hours

03 Mono Energy-save Mode

Set whether to run Monochrome printing in energy-save mode.

ON, OFF

02 Date/Time Setting

Set the current date and time, the daylight-saving time, and the time difference.

Setting Time

Daylight Saving Time: OFF, ON (1 to 150 min.)

Time Zone

03 Weekly Timer Setting

01 Weekly Timer ON/OFF Setting

Specify whether or not to use the Weekly Timer function.

Weekly Timer ON, Weekly Timer OFF

02 Time Setting

Set the ON/OFF times in hours and minutes.

-

03 Date Setting

Set the ON/OFF condition of the machine for a given day of a given month.

-

04 Select Time for Power Save

Set the machine to turn off and then on during the lunch break.

ON, OFF

05 Password Non-Business Hours

Set a password to use the machine by turning on the power temporarily while the machine is in off condition due to the Weekly Timer function.

0000 (4 digits)

04 Restrict User Access

01 Function Usage Restriction

Specify whether or not to allow the use of various functions.

Sample Print: Allow, Restrict

USB Direct Print: Allow, Restrict

05 Expert Adjustment

01 Printer Adjustment

01 Restart Timing Adjustment

Adjust the image position of lead edge in paper feed direction in the printer engine.

Prerequisite:

FD-Mag. Adjustment is completed.

Objects of adjustment:

Restart Timing (Tray 1 to Tray 9), Restart Timing (Back), Tray Large Plain Offset, Tray Large Thick Offset, Tray Small Plain Offset, Tray Small Thick Offset, Large Plain Offset (ADU), Large Thick Offset (ADU), Small Plain Offset (ADU), Small Thick Offset (ADU)

Adjustment Range:

-60 (Lower) to +60 (Higher)

(1 step=0.1 mm)

02 Centering Adjustment

Adjust the image position in the crosswise direction of the printer engine.

Prerequisite:

CD-Mag. Adjustment is completed.

Adjustment Range:

Tray 1 to Tray 9, ADU, Large Size Offset (Tray 1 to Tray 9), Small Size Offset (Tray 1 to Tray 9), Large Plain Offset (ADU), Large Thick Offset (ADU), Small Plain Offset (ADU), Small Thick Offset (ADU), 8.5 5.5 Plain Offset (ADU), 8.5 5.5 Thick Offset (ADU)

Adjustment Range:

-40 (Front) to +40 (Back)

(1 step=0.1 mm)

03 FD-Mag. Adjustment

Adjust the magnification in paper feed direction in the printer engine.

Objects of adjustment:

Printer FD-Mag.

Adjustment Range:

-100 (Short) to +100 (Long)

(1 step = 0.01%)

Objects of adjustment:

Tray 1 Offset (ADU) to Tray 9 Offset (ADU)

Adjustment Range:

-80 (Short) to +20 (Long)

(1 step = 0.01%)

04 CD-Mag. Adjustment

Adjust the magnification in crosswise direction in the printer engine.

Objects of adjustment:

Printer CD-Mag., Tray 1 Offset (ADU) to Tray 9 Offset (ADU)

Adjustment Range:

-100 (Short) to +100 (Long)

(1 step = 0.01%)

05 Registration Loop Adj.

Adjust the paper loop amount in registration roller section.

Objects of adjustment:

Tray 1 Large Size to Tray 9 Large Size, Tray 1 Small Size to Tray 9 Small Size, ADU Large Size, ADU Small Size, ADU Plain/W Under 150 mm, ADU Thick/W Under 150 mm, Thick

Adjustment Range:

-99 (Short) to +99 (Long)

(1 step = 0.1 mm)

06 Pre-registration Adj.

Adjust the paper loop amount in pre-registration roller section of the trays.

Objects of adjustment:

Tray1 to Tray9, 1st PFU Connecting Part, 2nd PFU Connecting Part

Objects of adjustment:

105 g/m2 or less, 106 to 256 g/m2, 257 g/m2 or more

Adjustment Range:

-99 (Short) to +99 (Long)

(1 step = 0.1mm)

07 Print Job JAM Setting

Set whether or not to stop the machine as a paper jam when a mis-centering is detected. And set whether or not to display a message indicating the cause of the JAM when the machine stops as JAM.

Mis-centering JAM Setting: Detect, Not Detect

JAM Identification Display: Display, Not Display

02 Finisher Adjustment (Finisher FS-532)

This menu item is to be displayed and allowed on the machine mounted with Finisher FS-532.

01 Staple Finisher Adjustment

01 Staple Finisher(Main) Adj.

01 Exit Guide Paper Width Adj.

Adjust the exit guide alignment pitch to be used by the staple finisher.

Make adjustment if output paper stack on main tray is uneven in straight delivery.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 short edge feed/long edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 short edge feed/long edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 13 19 short edge feed, B5 short edge feed, A6 short edge feed / Postcard, SRA4 long edge feed, B6 short edge feed, 16K short edge feed, Custom (380 to 488 mm), Custom (220 to 379 mm), Custom (139 to 219 mm)

Adjustment Range:

-50 (Wide) to +50 (Narrow)

(1 step=0.1 mm)

02 Upper Gripper Operation

Select the upper gripper operation for main tray outlet.

Auto, ON, OFF

03 Output Alignment Operation

Select operation for output alignment.

Auto, ON, OFF

04 Staple Paper Width Adj.

Adjust the board alignment width of the staples in the staple finisher.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed/short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed/short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 13 19 short edge feed, SRA4 long edge feed, 16K short edge feed, Custom (380 to 488 mm, Custom (220 to 379 mm), Custom (139 to 219 mm)

Adjustment Range:

-20 (Wide) to +20 (Narrow)

(1 step=0.1 mm)

05 FD Alignment Plate Adj.

Adjust the vertical alignment fitting for staples in the staple finisher.

Objects of adjustment:

Offset for All Sizes, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, 9 11 long edge feed, Custom (139 to 230 mm)

Adjustment Range:

-50 (Wide) to +50 (Narrow)

(1 step=0.1 mm)

06 Staple Position Adjustment

Adjust 2 position staple pitch and corner staple positions in staple finisher.

Objects of adjustment:

2 Position Pitch (120 mm), 2 Position Pitch (140 mm), 2 Position Pitch (165 mm), Rear Diagonal

Adjustment Range:

-5 (Narrow) to +5 (Wide)

(1 step = 1.0 mm)

Objects of adjustment:

Rear Parallel, Front Parallel

Adjustment Range:

-3 (Narrow) to +3 (Wide)

(1 step = 1.0 mm)

07 Rewind Paddle Descent Adj.

Adjust rewind paddle descent.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed/short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed/short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 13 19 short edge feed, SRA4 long edge feed, 16K short edge feed, Custom (380 to 488 mm, Custom (220 to 379 mm), Custom (139 to 219 mm)

Adjustment Range:

-10 (Little) to +10 (Much)

(1 step = 0.2 mm)

08 Rewind Function Operation

Select the rewind paddle operation.

Auto, ON, OFF

02 Staple Finisher(Fold) Adj.

This menu item is to be displayed and become configurable on Finisher FS-532 mounted with Saddle Stitcher SD-510.

01 Fold&Staple Paper Width Adj.

Adjust pitch of alignment plate in Saddle Stitcher SD-510 if half-folded or multi tri-folded sheets show misalignment.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, 13 19 short edge feed, Custom (380 to 488 mm), Custom (240 to 379 mm)

Adjustment Range:

-50 (Narrow) to +50 (Wide)

(1 step=0.1 mm)

02 Fold&Staple Pitch Adjustment

Adjust staple pitch in Saddle Stitcher SD-510. Make this adjustment if staple pitch is not within the allowance range.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, 13 19 short edge feed, Custom (380 to 488 mm), Custom (240 to 379 mm)

Adjustment Range:

-300 (Narrow) to +300 (Wide)

(1 step=0.1 mm)

03 Fold&Staple Fold Position

Adjust half-fold position of fold & staple function in Saddle Stitcher SD-510. Make this adjustment if half-fold position is not within the specified range.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, 13 19 short edge feed, Custom (380 to 488 mm), Custom (240 to 379 mm)

Adjustment Range:

Top face of output paper: -50 (Extend) to +50 (Shorten)

(1 step=0.1 mm)

04 Fold&Staple Staple Position

Adjust staple position in Saddle Stitcher SD-510.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, 13 19 short edge feed, Custom (380 to 488 mm), Custom (240 to 379 mm)

Adjustment Range:

Top face of output paper: -50 (Extend) to +50 (Shorten)

(1 step=0.1 mm)

05 Half-Fold Fold Position Adj.

Adjust half-fold position of fold function in Saddle Stitcher SD-510.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, 13 19 short edge feed, Custom (380 to 488 mm), Custom (240 to 379 mm)

Adjustment Range:

Top face of output paper: -50 (Extend) to +50 (Shorten)

(1 step=0.1 mm)

06 Tri-Fold Adjustment

01 Tri-Fold Position Adjustment

Adjust Fold 1 and Fold 2 positions for multi tri-folding in Saddle Stitcher SD-510.

Make this adjustment if each fold position for tri-folding is not within the allowance range.

Objects of adjustment:

8.5 11 short edge feed, A4 short edge feed, 16K short edge feed

Adjustment Range:

Fold 1: -50 (Extend) to +50 (Shorten)

(1 step=0.1 mm)

Fold 2: -50 (Shorten) to +50 (Extend)

(1 step=0.1 mm)

02 Double Fold Plate Adjustment

Adjust double fold plate in saddle stitcher.

Deepen in case of wide shift in bunch of the Fold 2.

Objects of adjustment:

8.5 11 short edge feed, A4 short edge feed, 16K short edge feed

Adjustment Range:

-50 (Shallow) to +50 (Deep)

(1 step=0.1 mm)

07 Half-Fold Strength Adj.

To adjust the opening of booklets, increase the roller pressure time.

* You cannot adjust the strength to fold booklets.

* Long pressure time causes reduced productivity.

Adjustment Range:

(Additional time) 0 to +10

(1 step = 1 sec)

03 Staple Finisher(Punch) Adj.

This menu item is to be displayed and configurable on Finisher FS-532 mounted with Punch Kit PK-522.

01 Registration Adjustment

If the punch position is not parallel to the paper edge, control the paper curl and wrinkle by adjusting the paper loop amount of the registration roller.

Adjustment Range:

-50 (Short) to +50 (Long)

(1 step=0.1 mm)

02 Horizontal Position Adj.(FD)

Adjust the distance between the edge of the printed paper and the center of punch holes.

Objects of adjustment:

Offset for All Size, A3 short edge feed, A4 long edge feed, A4 short edge feed, SRA4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 8.5 14 short edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 9 11 long edge feed, B5 short edge feed

Adjustment Range:

-50 (Far) to +50 (Close)

(1 step=0.1 mm)

03 Vertical Position Adj.(CD)

Adjust the misalignment in center positions of paper and punch holes for each paper size.

Objects of adjustment:

Offset for All Size, A3 short edge feed, A4 long edge feed, A4 short edge feed, SRA4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 8.5 14 short edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 9 11 long edge feed, B5 short edge feed

Adjustment Range:

-50 (Forward) to +50 (Backward)

(1 step=0.1 mm)

04 Staple Finisher(PI) Adj.

This menu item is to be displayed and configurable on Finisher FS-532 mounted with Post Inserter PI-502.

01 PI Registration Adjustment

When paper fed from the upper or lower tray of Post Inserter PI-502 has skew or wrinkle, or causes paper jam, adjust the paper loop of the registration roller.

Objects of adjustment:

PI Upper Tray, PI Lower Tray

Adjustment Range:

-5 (Short) to +5 (Long)

(1 step = 1.0 mm)

02 Finisher Adjustment (Output Tray OT-510)

This menu item is displayed and can be set on the machine mounted with Output Tray OT-510.

01 Staple Finisher Adjustment

01 Staple Finisher(Main) Adj.

01 Exit Guide Paper Width Adj.

Adjust the exit guide alignment pitch to be used by the staple finisher.

Make adjustment if output paper stack on main tray is uneven in straight delivery.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 13 19 short edge feed, B5 short edge feed, A6 short edge feed / Postcard, SRA4 long edge feed, B6 short edge feed, 16K short edge feed, Custom (380 to 488 mm, Custom (220 to 379 mm), Custom (139 to 219 mm)

Adjustment Range:

-50 (Wide) to +50 (Narrow) (1 step = 0.1 mm)

02 Upper Gripper Operation

Select the upper gripper operation for main tray delivery exit.

Auto, ON, OFF

03 Output Alignment Operation

Select operation for output alignment.

Auto, ON, OFF

02 Finisher Adjustment (Folding Unit FD-503)

This menu item is to be displayed and allowed on the machine mounted with Folding Unit FD-503.

02 Multi Folder Adjustment

01 Multi Folder(Punch) Adj.

01 Paper Width Adjustment

Adjust the misalignment of punch hole positions.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed/long edge feed, B5 short edge feed/long edge feed, A5 short edge feed/long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed/long edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed/long edge feed, 9 11 long edge feed

Adjustment Range:

-20 (To reduce the randomness) to +20 (To reduce the tilts)

(1 step = 0.1 mm)

02 Punch Vertical Position Adj.

01 2-Hole Punch

Adjust the vertical position of punch holes made by the folding unit.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed/long edge feed, B5 short edge feed/long edge feed, A5 short edge feed/long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed/long edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed/long edge feed, 9 11 long edge feed

Adjustment Range:

-40 (To move to the center) to +40 (To move to the edge)

(1 step = 0.1 mm)

02 3-Hole Punch

Adjust the vertical position of punch holes made by the folding unit.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, A4 long edge feed, B5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 11 long edge feed, 8K short edge feed, 16K long edge feed, 9 11 long edge feed

Adjustment Range:

-40 (To move to the center) to +40 (To move to the edge)

(1 step=0.1 mm)

02 Multi Folder(Fold) Adj.

01 Half-Fold Position Adj.

Adjust the folded position for half-fold.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range:

-50 (To shorten the top face) to +50 (To lengthen the top face)

(1 step = 0.1 mm)

02 Z-Fold Position Adj.

Adjust the fold positions for Z-folding.

Start with Fold 1, and then set Fold 2.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range:

Fold 1: -50 (To narrow) to +50 (To widen)

(1 step = 0.1 mm)

Fold 2: -50 (To narrow) to +50 (To widen)

(1 step = 0.1 mm)

03 Tri-Fold-in Pos. Adj.

Adjust the fold positions for tri-fold-in.

Start with Fold 1, and then set Fold 2.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range:

Fold 1: -50 (To narrow) to +50 (To widen)

(1 step = 0.1 mm)

Fold 2: -50 (To narrow) to +50 (To widen)

(1 step = 0.1 mm)

04 Tri-Fold-out Pos. Adj.

Adjust the fold positions for tri-fold-out.

Start with Fold 1, and then set Fold 2.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range:

Fold 1: -50 (To widen) to +50 (To narrow)

(1 step = 0.1 mm)

Fold 2: -50 (To narrow) to +50 (To widen)

(1 step = 0.1 mm)

05 Double Parallel Pos. Adj.

Adjust the fold positions for double parallel folding.

Start with Fold 1, and then set Fold 2.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range:

Fold 1: -50 (To narrow) to +50 (To widen)

(1 step = 0.1 mm)

Fold 2: -50 (To narrow) to +50 (To widen)

(1 step = 0.1 mm)

06 Gate Position Adj.

Adjust the fold position for gate folding.

Start with Fold 1, and then set Fold 2 and Fold 3.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range:

Fold 1: -50 (To narrow) to +50 (To widen)

(1 step = 0.1 mm)

Fold 2: -50 (To widen) to +50 (To narrow)

(1 step = 0.1 mm)

Fold 3: -50 (To narrow) to +50 (To widen)

(1 step = 0.1 mm)

02 Finisher Adjustment (Large Capacity Stacker LS-506)

This menu item is to be displayed and allowed on the machine mounted with Large Capacity Stacker LS-506.

When two stackers are installed, you can configure a setting for each stacker.

03 Stacker Adjustment

01 Paper Width Adjustment

Adjust the position of adjustment plates if output sheets show misalignment in crosswise direction on the stacker tray.

Objects of adjustment:

Stacker No. 1, Stacker No. 2

Adjustment Range:

-20 (To reduce the dispersion) to +20 (To reduce the distortion)

(1 step = 0.1 mm)

02 Paper Length Adjustment

Adjust the position of the stopper if output sheets show misalignment in paper feed direction on the stacker tray.

Objects of adjustment:

Stacker No. 1, Stacker No. 2

Adjustment Range:

-20 (To reduce the dispersion) to +20 (To reduce the distortion)

(1 step = 0.1 mm)

02 Finisher Adjustment (Saddle Stitcher SD-506)

This menu item is to be displayed and allowed on the machine mounted with Saddle Stitcher SD-506.

04 Saddle Stitcher Adjustment

01 Fold Paper Width Adj.

Adjust the width of adjustment plates if half-folded or tri-folded sheets show misalignment.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 463 mm), Custom (257 to 379 mm)

Adjustment Range:

-50 (To reduce the misalignment) to +50 (To reduce the distortion)

(1 step = 0.1 mm)

02 Half-Fold Position Adj.

Adjust the fold position determined by the half-folder.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 463 mm), Custom (257 to 379 mm)

Adjustment Range:

-50 (To shorten the top face) to +50 (To lengthen the top face)

(1 step = 0.1 mm)

03 Staple Paper Width Adj.

Adjust the width of adjustment plates of the saddle stitcher to be used in Staple mode.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 463 mm), Custom (257 to 379 mm)

Adjustment Range: -20 (To reduce the dispersion) to +20 (To reduce the distortion)

(1 step = 0.1 mm)

04 Staple Center Position

Adjust the center position of staples determined by the saddle stitcher.

Prerequisite: Staple paper width adjustment is completed.

Adjustment Range:

-20 (To move closer to paper center(fold)) to +20 (To move away from paper center(fold))

(1 step = 0.1 mm)

05 Staple Pitch Adjustment

Adjust the staple pitch determined by the saddle stitcher.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 463 mm), Custom (257 to 379 mm)

Adjustment Range:

-20 (To shorten) to +20 (To lengthen)

(1 step = 1.0 mm)

06 Trimming Adjustment

Adjust the trimming width.
The trim width should be more than 2.0 mm, otherwise the trimming operation may not be performed properly.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 463 mm), Custom (257 to 379 mm)

Adjustment Range:

-400 (To narrow) to +400 (To widen)

(1 step = 0.1 mm)

07 Tri-Fold Position Adj.

Adjust the folded positions in Tri-Fold mode.

Start with Fold 1, and then set Fold 2.

Objects of adjustment:

Offset for All Size, A4 short edge feed, 8.5 11 short edge feed

Adjustment Range:

Fold 1: -100 (To widen) to +100 (To narrow)

(1 step = 0.1 mm)

Fold 2: -100 (To narrow) to +100 (To widen)

(1 step = 0.1 mm)

08 Trimmer Receiver Adj.

Frequent trimming operations may cause damage to the receiver, resulting in trimming failures. Move the receiver automatically or manually.

*Trimmer Receiver Adj. is not displayed by default. To use this setting, please contact your service representative.

Objects of Adjustment: Trim Count

Adjustment Range: 700 times, 500 times, 300 times

Objects of adjustment: Move Pitch

Adjustment Range: 1.0 mm, 1.5 mm, 2.0 mm

02 Finisher Adjustment (Saddle Stitcher SD-513)

This menu item is to be displayed and allowed on the machine mounted with Saddle Stitcher SD-513.

04 Saddle Stitcher Adjustment

01 Fold Paper Width Adj.

Adjust the width of adjustment plates if half-folded or tri-folded sheets show misalignment.

Adjustment Range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, PI Paper, Custom (380 to 488 mm), Custom (257 to 379 mm), 13 19 short edge feed

Adjustment Range:

-50 (To reduce the misalignment) to +50 (To reduce the distortion)

(1 step = 0.1 mm)

02 Fold Skew Adjustment

Adjust the skew of the folding line.

Objects of Adjustment: Single-Fold, Multi-Fold

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, PI Paper, Custom (380 to 488 mm), Custom (257 to 379 mm), 13 19 short edge feed

Adjustment Range:

-50 (To decrease) to +50 (To increase)

(1 step = 0.1 mm)

03 Half-Fold Position Adj.

Adjust the folded position for half-fold.

Adjustment Range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm), 13 19 short edge feed

Adjustment Range:

-50 (To shorten the top face) to +50 (To lengthen the top face)

(1 step = 0.1 mm)

04 Tri-Fold Position Adj.

Adjust the folded positions in Tri-Fold mode.

Adjust Fold 1 and Fold 2 in this order.

Adjustment Range:

Offset for All Size, A4 short edge feed, 8.5 11 short edge feed

Adjustment Range:

Fold 1: -100 (To widen) to +90 (To narrow)

(1 step = 0.1 mm)

Fold 2: -50 (To widen) to +50 (To narrow)

(1 step = 0.1 mm)

05 Crease Position Adjustment

Adjust the crease position.

01 Half-Fold Crease Position

Move the half-fold crease position.

Adjustment Range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm), 13 19 short edge feed

Adjustment Range:

-20 (To shorten) to +20 (To lengthen)

(1 step = 0.1 mm)

02 Tri-Fold Crease Position

Move the tri-fold crease position.

Adjustment Range:

Fold 1, Fold 2: Offset for All Size, A4 short edge feed, 8.5 11 short edge feed

Adjustment Range:

-20 (To shorten) to +20 (To lengthen)

(1 step = 0.1 mm)

03 PB Cover Crease Position

Move the perfect binding cover crease position.

Adjustment Range:

Crease 1, Crease 2: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm), 13 19 short edge feed

Adjustment Range:

-20 (To shorten) to +20 (To lengthen)

(1 step = 0.1 mm)

06 Staple Paper Width Adj.

Adjust the width of adjustment plates of the saddle stitcher to be used in Staple mode.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm), 13 19 short edge feed

Adjustment Range: -20 (To reduce the dispersion) to +20 (To reduce the distortion)

(1 step = 0.1 mm)

07 Staple Center Position

Adjust the center position of staples determined by the saddle stitcher.

Prerequisite: Staple paper width adjustment is completed.

01 2 Position Staple

Adjust the center position for 2-position staple.

Adjustment Range:

-20 (To move closer to rear edge) to +20 (To move closer to front edge)

(1 step = 0.1 mm)

02 4 Position Staple(Front 2)

Adjust the center position at two locations on the front edge for 4-position staple.

Objects of adjustment:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm)

Adjustment Range: -100 (To move closer to rear edge) to +100 (To move closer to front edge)

(1 step = 0.1 mm)

02 4 Position Staple(Rear 2)

Adjust the center position at two locations on the rear edge for 4-position staple.

Objects of adjustment:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm)

Adjustment Range: -100 (To move closer to rear edge) to +100 (To move closer to front edge)

(1 step = 0.1 mm)

08 Staple Pitch Adjustment

Adjust the staple pitch determined by the saddle stitcher.

01 2 Position Staple

Adjust the pitch for 2-position staple.

Adjustment Range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm), 13 19 short edge feed

Adjustment Range:

-20 (To shorten) to +20 (To lengthen)

(1 step = 1.0 mm)

02 4 Position Staple(Front 2)

Adjust the pitch at two locations on the front edge for 4-position staple.

Adjustment Range:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm)

Adjustment Range:

-10 (To narrow) to +10 (To widen)

(1 step = 1 mm)

02 4 Position Staple(Rear 2)

Adjust the pitch at two locations on the rear edge for 4-position staple.

Adjustment Range:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm)

Adjustment Range:

-10 (To narrow) to +10 (To widen)

(1 step = 1.0 mm)

09 Staple Offset Adjustment

Adjust the misalignment between the stapling positions and folding line.

Adjustment Range:

-10 (To move to the left) to +10 (To move to the right)

(1 step = 0.1 mm)

10 Staple Tip Adjustment

Change the staple leg shape.

Adjustment Range:

-9 (To round the staple leg) to +9 (To level the staple leg)

(1 step = 1 msec)

11 Flattening a Fold (Strength)

Adjust the spine shape while changing the strength to form the book spine.

Adjustment Range:

-20 (To weaken) to +20 (To strengthen)

(1 step = 0.1 mm)

12 Flattening a Fold (Freq.)

Adjust the number of roller reciprocation times to form the book spine.

Adjustment Range:

-5 (To decrease) to +5 (To increase)

(1 step = 1 roller reciprocation operation)

13 Parallel Trimming Adjustment

Adjust the levelness between the trimming line and cut edge.

Adjustment Range:

Front, Rear

Adjustment Range:

0 (To narrow) to +30 (To widen)

(1 step = 0.1 mm)

14 Fore-edge Trimming Adj.

Adjust the trimming width.

The trimming width should be more than 5 mm, otherwise the trimming operation may not performed properly.

Adjustment Range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm), 13 19 short edge feed

Adjustment Range:

-400 (To narrow) to +400 (To widen)

(1 step = 0.1 mm)

15 2-Side Slitting Adjustment

Adjust the 2-side slitting.

Adjustment Range:

Front, Rear

Adjustment Range:

-10 (To narrow) to +10 (To widen)

(1 step = 0.1 mm)

16 2-Side Slit Finishing Adj.

Change the 2-side trimming speed to adjust skew and napping conditions.

Objects of adjustment:

61 g/m2 or Less, 62 g/m2 or More

Adjustment Range:

-4 (Slow) to +4 (Fast)

(1 step = 5 mm/sec.)

17 Trimmer Receiver Adj.

Frequent trimming operations may cause damage to the receiver, resulting in trimming failures. Move the receiver automatically or manually.

*Trimmer Receiver Adj. is not displayed by default. To use this setting, please contact your service representative.

Objects of Adjustment: Trim Count

Adjustment Range: 700 times, 500 times, 300 times

Objects of adjustment: Move Pitch

Adjustment Range: 1.0 mm, 1.5 mm, 2.0 mm

02 Finisher Adjustment (Perfect Binder PB-503)

This menu item is to be displayed and allowed on the machine mounted with Perfect Binder PB-503.

05 Perfect Binder Adjustment

01 Sub Compile CD Width Adj.

Adjust misalignment or distortion in the crosswise direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed/long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 16K long edge feed, Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-20 (To reduce the distortion) to +20 (To reduce the misalignment)

(1 step = 0.1 mm)

02 Clamp CD Width Adjustment

Adjust misalignment or distortion in the crosswise direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed/long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 16K long edge feed, Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-20 (To reduce the distortion) to +20 (To reduce the misalignment)

(1 step = 0.1 mm)

03 Clamp FD Position Adj.

Adjust misalignment or distortion in the paper feed direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed/long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 16K long edge feed, Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-20 (To reduce the distortion) to +20 (To reduce the misalignment)

(1 step = 0.1 mm)

04 Glue Start Position

Adjust the position to start gluing on the body. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Ahead: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed/long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 16K long edge feed, Custom (220 to 379 mm), Custom (148 to 219 mm)

Back: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed/long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 16K long edge feed, Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-128 (To increase) to +127 (To decrease)

(1 step = 0.1 mm)

05 Glue Finish Position

Adjust the position to finish gluing on the body. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Ahead: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed/long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 16K long edge feed, Custom (220 to 379 mm), Custom (148 to 219 mm)

Back: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed/long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 16K long edge feed, Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-128 (To decrease) to +127 (To increase)

(1 step = 0.1 mm)

06 Cover Lead Edge Adj.

Adjust the position of the lead edge of the left cover sheet. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

PB Tray: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, Custom (220 to 379 mm), Custom (148 to 219 mm)

Except PB Tray: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-128 (To move closer to the body) to +127 (To move further from the body)

(1 step = 0.1 mm)

07 Cover Trimming Adjustment

Adjust the trimming width of the right cover sheet. To align the lead edges of left and right cover pages, be sure to perform Cover Lead Edge Adjustment in advance.

Objects of adjustment:

Perfect Binder Tray, Except PB Tray

Adjustment Range:

-128 (To narrow) to +127 (To widen)

(1 step = 0.1 mm)

08 Cover Up/Down CD Width Adj.

Adjust the misalignment between the cover sheet and body.

Objects of adjustment:

Perfect Binder Tray, Except PB Tray

Adjustment Range:

-20 (To reduce the distortion) to +20 (To reduce the misalignment)

(1 step = 0.1 mm)

09 Spine Corner Forming Pos.

Adjust the spine corners formed in cover sheets.

Objects of adjustment:

Up/Down Forward Adj., Up/Down Rear Adj.

Adjustment Range:

-128 (To convex) to +127 (To concave)

(1 step = 0.1 mm)

10 Temperature Adjustment

Glue Tank -Low:

Adjust the temperature to control the tank heater.

Low temperature: increases glue viscosity, High temperature: decreases glue viscosity

Glue Apply Roller:

Adjust the temperature to control the roller heater. This also supports heating of the glue.

Low temperature: increases glue viscosity, High temperature: decreases glue viscosity

Objects of Adjustment: Glue Tank -Low

Initial: 185°C

Adjustment Range:

180°C (Down: viscosity increased) to 190°C (Up: viscosity decreased)

(1 step = 1°C)

Objects of adjustment: Glue Apply Roller

Initial: 165°C

Adjustment Range:

160°C (Down: viscosity increased) to 170°C (Up: viscosity decreased)

(1 step = 1°C)

03 Process Adjustment

01 Front & Back Density

Specify the adjustment value for front and back transfer output voltage automatically set by the machine.

Be sure to perform Color Density Manual Control after changing the maximum density.

Objects of adjustment:

1st Transfer Y, 1st Transfer M, 1st Transfer C, 1st Transfer K, 1st Transfer (Monochrome), 2nd Transfer Front, 2nd Transfer Back

Adjustment Range: -30 to +30%

02 Toner Density Sensor Speed

Readjust the voltage value to control the toner density for Line Speed 2 or Line Speed 3 in order to correct problems caused by unstable toner density such as image fogging and toner scattering.

Objects of adjustment:

Line Speed 2, Line Speed 3

03 Maximum Density Adjustment

Adjust the maximum density for each of Y, M, C, and K. The machine will start the Gamma Automatic Adjustment after you change the maximum density. When the Gamma Automatic Adjustment is completed, proceed to the calibration with the image controller.

Be sure to perform Color Density Manual Control after changing the maximum density.

Yellow: -10 (Light) to +10 (Dark)

Magenta: -10 (Light) to +10 (Dark)

Cyan: -10 (Light) to +10 (Dark)

Black: -10 (Light) to +10 (Dark)

04 1st Trans. Dis-elec. Output

Set the discharging voltage to measure the AC/DC current values of the 1st Transfer Dis-elec. Pole Output of each color (Y/M/C/K).

Yellow: Standard, Condition1, Condition2

Magenta: Standard, Condition1, Condition2

Cyan: Standard, Condition1, Condition2

Black: Standard, Condition1, Condition2

05 Max. Density Auto Adj. (RU)

Automatically print and scan charts and then adjust the maximum density for each of Y, M, C, and K. The machine will start the Gamma Automatic Adjustment after you change the maximum density. When the Gamma Automatic Adjustment is completed, proceed to the calibration with the image controller. Be sure to perform Color Density Manual Control after changing the maximum density.

05 Max. Density Auto Adj. is displayed instead when Integrated Color Care Unit IQ-501 is not mounted on the machine.

06 Develop AC Bias Fine Adj.

Adjust the development AC bias for each of the Y, M, C, and K colors when an image noise, white-spot, or reduction in reproducibility occurs.

Adjustment Range: Y, M, C, K

Adjustment Range:

-5 to +5 (Down:Lower reproducibility/Better noise or white-spot, / Up:Raise reproducibility)

07 Develop AC Freq. Fine Adj.

Adjust the development AC bias frequency for each of the Y, M, C, and K colors when an image fogging occurs or the reproducibility of white-spot is degenerated.

Adjustment Range: Y, M, C, K

Adjustment Range:

-6 to +5 (Down:Better white-spot/Worse covered-Margin / Up:Better covered-margin/Worse white-spot)

08 Granularity Setting

Adjust development conditions when an image noise (degradation of granularity) or sweeping (a phenomenon that causes toner to be swept to the rear edge in the paper feed direction of a halftone solid image, causing the rear edge to darken) occurs.

+3 (Normal), +2, +1

09 Development Output Fine Adj.

Adjust the development output for each of the Y, M, C, and K colors when an image fogging or white-spot occurs

Adjustment Range: Y, M, C, K

Adjustment Range:

-7 to +5 (Down:Better white-spot/Worse covered-margin, / Up:Better covered-margin/Worse white-spot)

04 Quality Adjustment

Adjust the image quality.

01 Highlight Adjustment

Change the printer gamma curve to adjust the gradation and background density in highlights.

Y, M, C, K

Adjustment Range: -128 (lighter) to +127 (darker)

02 Stabilization Adj. Setting

Set the frequency of the maximum density correction.

None, -2 (Low Frequency) to +2 (High Frequency)

03 Custom Screen

Select screens to be used as Screen 1, Screen 2, and Stochastic, respectively.

Screen 1: Dot270, Dot210, Dot190, Dot175, Dot150, Dot130, Line200, Line180, Line150

Screen 2: Dot270, Dot210, Dot190, Dot175, Dot150, Dot130, Line200, Line180, Line150

Stochastic: FM1, FM2, FM3

04 Controller Image Comp. Set

Make this setting to smooth the jagged outlines of the text or line images.

Gradation Priority, Resolution Priority

05 Tone Curve for Each Tag Setting

Select whether or not to allow tone curve adjustment for each tag (image, text/graphic).

Do Not Execute Adjustment, Execute Each Tag Adj.

06 Density Balance Adjustment

01 Density Balance Chart Output

Output the chart for density balance adjustment.

Objects of adjustment:

Colorimeter

i1-iSisXL / FD-9

Type 1: 8-point measurement

Type 2: 16-point measurement

i1-Pro / i1-Pro2

Type 1: 1-point measurement

Type 2: 3-point measurement

FD-5 BT

Type 1: 1-point measurement

Type 2: 3-point measurement

Type 3: 3-point measurement

02 Density Balance Data Reg/Del

Load the colorimetric data, or manually register the data on the machine.

05 Execute Adjust Operation

Execute each of the four adjustment operations manually.

Gamma Automatic Adj., Color Registration Adj., Toner Refresh Mode1, Toner Refresh Mode2, Fusing Refresh Mode, Charging Cleaning Mode, Drum Refresh Mode

06 Corner Staple(Back) Angle

Select between diagonal and parallel stapling on the left corner.

Diagonal, Parallel

06 List/Counter

Output the user setting list and the audit log report. Also, collectively save the data mentioned above on the USB flash drive connected to the USB port.

User Management List, Use Management List, Font Pattern List, Audit Log Report

07 Size Setting

Specify the settings related to paper sizes of the paper placed in the post inserter.

01 K Size

Specify whether or not to use the K sizes such as 8K and 16K.

ON, OFF

02 A4 Tab Width Setting

Select the tab width of A4-size tab paper.

12.7 mm, 15.0 mm

09 Perfect Binder Setting

This menu item is to be displayed and allowed on the machine mounted with Perfect Binder PB-503.

01 Usable Paper Weight Select

Set the paper weight available for body and cover paper, respectively, when using the perfect binder.

Usable Paper Weight Select

Body: 62-74g/m2, 75-80g/m2, 81-91g/m2, 92-105g/m2

Cover: 81-91g/m2, 92-105g/m2, 106-135g/m2, 136-176g/m2, 177-216g/m2

Change Weight Unit

g/m2, Duodecimo-kg, Octavo-kg, A Book-kg, B Book-kg, lb Bond, lb Index, lb Cover, lb Book, lb Bristol, lb Tag

02 Paper Count Limit for PB

Specify the minimum and maximum numbers of sheets to be bound as a body, individually for each paper weight.

This setting can be made individually for two paper types: Plain and Fine/Color Specific/Coated.

Plain:

62-74 g/m2 / 16-19 lb Bond

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 200, 250, 270, 300

75-80 g/m2 / 20-21 lb Bond

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 200, 250, 270, 300

81-91 g/m2 / 22-24 lb Bond

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 200, 250, 270, 300

92-105 g/m2 / 25-28 lb Bond

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 200, 250, 270, 300

Fine/Color Specific/Coated:

62-74 g/m2 / 16-19 lb Bond

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 110, 120, 130, 140, 150

75-80 g/m2 / 20-21 lb Bond

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 110, 120, 130, 140, 150

81-91 g/m2 / 22-24 lb Bond

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 110, 120, 130, 140, 150

92-105 g/m2 / 25-28 lb Bond

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 110, 120, 130, 140, 150

Change Weight Unit

g/m2, Duodecimo-kg, Octavo-kg, A Book-kg, B Book-kg, lb Bond, lb Index, lb Cover, lb Book, lb Bristol, lb Tag

03 Unfitting Cover Stop

Specify whether or not to stop the current job when the cover width is not suitable for the body size and spine thickness.

Temporary Stop, Not Temporary Stop

10 Operation Screen Customize

01 Font Weight Setting

Select the font weight for the screen.

Standard, Bold

02 Machine Function Key Setting

Change the layout of function keys displayed on the MACHINE screen.

-

Administrator Setting: Administrator Registration

Register the name, extension number, and e-mail address of the administrator. The administrator name and extension number are always displayed in the upper-right corner of the UTILITY screen.

  • Administrator Name Setting (Up to 20 one-byte characters)

  • Extension No. Setting (Up to eight digits)

  • E-mail Address Setting (Up to 250 one-byte characters)

Administrator Setting: User Auth./Account Track

Specify whether or not to use the user authentication and account track functions. You can also specify or change the conditions in authentication.

Menu Item/Description

Setting Items/Options (with default bolded)

1 General Settings

Specify the authentication method of the user authentication and account track.

User Authentication: Authenticate, OFF, External Server Authentication, ON (MFP)

Public User Access: ON (with Login), Restrict

Account Track: ON, OFF

Account Track Input Method: Account Name & Password, Password Only

Synchronize User Authentication & Account Track: Synchronize, Do Not Synchronize

When # of Jobs Reach Maximum: Stop Immediately, Stop After Print, Warning Only

Number of User Counters Assigned: 1 to 999

Ticket Hold Time Setting: 1 minute to 600 minutes

Count Sample Print: Yes, No

2 User Authentication Settings

1 Administrative Settings

Specify whether or not to display the user name list on the authentication screen. Also place the default function permissions on users for the authentication by an external server.

User Name List: ON, OFF

Default Function Permission

Print: Full Color/Black, Black Only, Restrict

User Box: Allow, Restrict

2 User Registration

Add, change, or delete entries of users to be allowed in user authentication.

User No., User Name, Password, E-mail Address, Account Name, Max. Allowance Set, Function Permission (Print or User Box)

3 User Counter

View or reset the count for each user.

-

3 Account Track Settings

1 Account Track Registration

Change, add, or delete accounts to be tracked.

Account Name, Password, Max. Allowance Set, Function Permission (Print or User Box)

2 Account Track Counter

View or reset the count for each account track.

-

4 Print without Authentication

Specify whether to make print function available to users without authentication.

Print: Full Color/Black, Black Only, Restrict

5 External Server Settings

Register an external server, or edit or delete a registered server when ON (External Serv) is selected as the Authentication Method.

-

6 Authentication Device Settings

1 General Settings

Specify the type of IC card used for entering credentials. Also, specify the authentication method.

IC Card Type Setting: FeliCa, SSFC, FCF, FCF (Campus), Type A, Felica+TypeA, SSFC+TypeA, FCF+TypeA, FCF (Campus)+TypeA

Operation Settings: Card Authentication, Card Authentication + Password

7 User/Account Common Setting

Specify whether or not to display a logout confirmation dialog.

Logout Confirmation Screen Display Setting: ON, OFF

Administrator Setting: Network Setting

Menu Item/Description

Setting Items/Options (with default bolded)

01 NIC Settings

Configure various NIC settings.

TCP/IP Settings, HTTP Server Settings, FTP Settings, SMB Settings, LDAP Settings, E-mail Settings, SNMP Settings, Bonjour Setting*, TCP Socket Settings, WebDAV Settings, DPWS Settings, SSDP Setting, Detail Settings, IEEE802.1x Authentication Settings, IWS Settings, Remote Panel Settings, JSP Setting, Hot Folder Setting

* To connect Bonjour in Macintosh, you need to configure TCP/IP setting in advance.

02 E-mail Initial Setting

Configure initial settings for e-mail or perform transmitting/receiving test.

Use E-mail System: ON, OFF

Time Zone, Trans (SMTP) Mail Server, SMTP Port Number, Trans Mail Server Timeout, New-arrival Check Interval, Receive Mail Server

Receive Mail Server Type: POP3, IMAP , POP3/IMAP Port Number, Receive Mail Account, Receive Mail Password, E-mail Address for Machine

POP (IMAP) before SMTP Auth.: ON, OFF

SSL Encryption of SMTP: ON, OFF

SSL Encryption of POP(IMAP) : ON, OFF

SMTP Authentication: ON, OFF

SMTP Authentication User ID, SMTP Authentication Password

03 http Communication Setting

Configure the http communication settings.

Enable Proxy Server: ON, OFF , Proxy Server Address, Proxy Server Port, Enable SSL, Enable Authentication: ON, OFF, Authentication User Name, Authentication Password

04 Quick Security Setting

01 Quick IP Filtering

Restrict access to the machine by means of IP address (IPv4/IPv6).

Filtering Method: No Filtering, Sync. IP Address, Sync. Subnet Mask

IPv4 Access Range, IPv6 Access Range

02 Administrator Password

Set an administrator password for the machine on which the administrator authentication function is set to OFF. The administrator authentication function is automatically turned ON.

Current Password, New Password, Input Confirmation

03 Password Rules Setting

Select whether or not to enable the password rules.

Enable, Disable

04 WebUtilities Setting

Select whether or not to use the functionality of Web Utilities.

ON, OFF

05 PSWC Setting

Select whether or not to use the PageScope Web Connection function.

Enable, Disable

06 Security Warning Display

Select whether or not to display the Security Setting Warning screen.

Display, Not Display

Administrator Setting: Common Setting

Menu Item/Description

Setting Items/Options (with default bolded)

One Shot Message Indication Time

Select the time span to display a shot message in the message area of the touch panel.

3 seconds, 5 seconds

Offset by Job Unit

Specify whether or not to offset the output sheets by job. Also specify the number of jobs to be offset when selecting ON for this function.

ON, OFF (Selecting ON: Offset Job Number, Initial Value: 1)

Continuation Print

Specify whether or not to output multiple reserve jobs in succession without stopping the machine at a job break.

Printer ON, Printer OFF

Back Side Magnification Adjustment

Select whether or not to activate the back side magnification adjustment mode for both sides adjust.

ON, OFF

Fusing Stability (Mixed Media)

Select what to prioritize when fusing.

Best Quality, Better Quality, Speed, Highest Speed

Prior Paper Type

Specify the temperature setting of the fusing section on standby. It can shorten the waiting time before printing by selecting a frequently used paper.

Others, Coated

Dash Length(Page Stamp)

Select the length of the dash to be used in a style of Page No. in Stamp.

Long, Short

Center Crop Mark Trim Margin

Specify the space between the center crop mark and image area (center crop mark trim margin).

0.0 mm to 20.0 mm (Default: 1.0)

Schedule Cross Axis Unit (Default)

Select the unit of horizontal axis on the Schedule screen.

Timetable, Time Frame (m), Sheet Volume

Hold Job Status after Output (Default)

Select the default value to delete or save the data of hold job after outputting.

Delete, Save

Offset Output Mode

Specify how to offset the output sets.

Change Out Pos., Stop Print, Change Out Position + Partition Paper (Tray1 to Tray9, PI 1, PI 2), Partition Paper (Tray1 to Tray9, PI 1, PI 2)

Hold Job Direct Output (Default)

Select the default for the Direct Output check box under the Hold Job screen.

ON selects the check box, and OFF clears the check box.

After the change, turn OFF/ON the sub power switch to apply the setting.

ON, OFF

Needless Tab Paper Exit

Specify whether or not to automatically discharge the oddments of tabbed sheets loaded in a tray as a set.

ON, OFF

Remaining Memory (Measurement Unit)

Select the unit of displaying the remaining memory.

%, GB

Remaining Memory (Warning)

Select the percentage at which to give warning when the remaining memory is low.

5% or Less, 10% or Less

[Proof Copy] 1 Set/1st Sheet Selection

If it is turned ON, the confirmation window is opened and you are asked to output one confirmation copy or to output only its first page when the Proof Copy is pressed.

ON, OFF

Both Sides Rotate/Skew

If Disable is selected, the Rotate/Skew adjustment does not become available and does not function.

Enable, Disable

Auto Image Adjustment Deviation Check

Select whether to automatically check a deviation. If you select ON, enter the specified value of a deviation.

ON (ON: 0.5 mm to 10.0 mm, Default: 2.0), OFF

Operation after Deviation Detected

Select how to perform operations when a deviation is detected. If you select Continue Output, select the paper tray to output data to and the number of deviation detection times.

Stop, Continue Output, Partition Paper (Tray1 to Tray9), Detection Count (2 to 10 times, Default: 2)

Select Chart Type (Auto Image Adj.)

Select an automatic image adjustment chart for each paper weight.

Type1, Type2

Administrator Setting: System Connection

Menu Item/Description

Setting Items/Options (with default bolded)

1 OpenAPI Settings

Set the OpenAPI information.

Access Setting: Allow, Restrict

SSL/Port Settings

Authentication: ON, OFF, Login Name, Password

Proxy Settings: Port Number (HTTP, HTTPS, FTP), Host Address, User Name, Password

2 Call Remote Center

Press Start to call your service representative via CS Remote Care.

Start

3 Browser Screen Setting

OpenAPI/IWS Appli. Size Set.

Specify the screen size of the OpenAPI or IWS application.

Small Size, Large Size

Screen Saver Size Setting

Specify the screen size of the screen saver.

Small Size, Large Size

Administrator Setting: Security Setting

Menu Item/Description

Setting Items/Options (with default bolded)

01 Administrator Password

Change the administrator password.

For details about the default administrator password, refer to Safety Information.

02 HDD Management Setting

01 HDD Lock Password

Change the HDD lock password.

-

02 Delete Temp. Data Setting

Specify whether or not to overwrite the temporary image data on the memory, and also the erase mode for deleting temporary data.

Setting Switch: ON, OFF

Erase Mode: Mode 1, Mode 2

03 Delete All Data Setting

Select the desired erase mode to delete all the data on the HDD or the non-volatile memory of this machine. Also execute deleting all the data.

Erase Mode: Mode 1 to 8

Execute Deletion

04 Delete Hold Job

Use this function to delete hold jobs.

-

05 Delete HDD Job

Use this function to delete the jobs saved on the HDD.

-

06 Delete Secure Job

Use this function to delete secure jobs from the security job box.

07 HDD Restore/Backup

Make a backup of, or restore the HDD.

01 HDD ALL Backup

Create a backup of all the hold job and HDD job saved on the HDD onto an external storage medium connected to the USB port.

Start

02 HDD ALL Restore

Restore the backup data created using HDD ALL Backup.

Start

03 HDD BOX Backup

Create a backup of the jobs in the backup folder of the HDD job onto an external medium connected to the USB port.

Start

04 HDD BOX Restore

Restore the backup data created using HDD BOX Backup.

Start

05 Controller Backup

Create a backup of setting data saved on the Image Controller IC-604 onto an external storage medium connected to the USB port.

Start

06 Controller Restore

Restore the backup data created using Controller Backup.

Start

08 HDD Encryption Setting

Set whether or not to save all jobs saved on the HDD upon encrypting them, and set the encryption password.

ON, OFF
12345678

09 HDD Job Auto Delete Period

Set the time when the jobs on hold are automatically deleted.

Not Delete, 12 hours, 1 day, 2 days, 3 days, 7 days, 30 days

03 Enhanced Security Mode

Specify whether or not to activate the Enhanced Security mode.

ON, OFF

Administrator Setting: OpenAPI Auth. Management

Register or check the restriction code in Restriction Code Settings.

  • Index

  • Vendor

  • Application

Touch Panel Adjustment

Use this function to check that the keys displayed on the screen and the touch sensor are properly aligned, if the machine does not respond to the press on the touch panel properly.

Quick Security Setting

Menu Item/Description

Setting Items/Options (with default bolded)

01 Quick IP Filtering

Restrict access to the machine by means of IP address (IPv4/IPv6).

Filtering Method: No Filtering, Sync. IP Address, Sync. Subnet Mask

IPv4 Access Range, IPv6 Access Range

02 Administrator Password

Set an administrator password for the machine on which the administrator authentication function is set to OFF. The administrator authentication function is automatically turned ON.

Current Password, New Password, Input Confirmation

03 Password Rules Setting

Select whether or not to enable the password rules.

Enable, Disable

04 WebUtilities Setting

Select whether or not to use the functionality of Web Utilities.

ON, OFF

05 PSWC Setting

Select whether or not to use the PageScope Web Connection function.

Enable, Disable

06 Security Warning Display

Select whether or not to display the Security Setting Warning screen.

Display, Not Display