Staple Pitch Adjustment
2 Position Staple Pitch
Adjust the 2-position staple pitch in Saddle Stitcher SD-513.
Objects of Adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm), 13 19 short edge feed
NOTICE
If a numeric value is specified for Offset for All Size, it is applied to all paper sizes. With a specific paper size selected,the set value becomes the sum of the entered value and the value previously specified for Offset for All Size.
Press Adjustment on the MACHINE screen to display the Adjustment Menu screen.
Press Finisher Adjustment, Saddle Stitcher Adjustment, Staple Pitch Adjustment, and 2 Position Staple in sequence.
Select the size to be adjusted using down or up.
Press Print Mode.
Load the paper with the size to be adjusted, then select that tray.
Press Start on the control panel.
A sample pattern will be output.
Check the staple pitch (a) of the sample.
If any adjustment is required, press Exit PrintMode to return to the Staple Pitch Adjustment screen.
Use the touch panel keypad to enter the set value.
supplementary explanationUse +/- to specify the value to be positive or negative.
supplementary explanationPress Set to change the Current Value.
supplementary explanationAdjustment Range: -20 (To shorten) to +20 (To lengthen) (1 step = 1.0 mm)
Repeat steps 4 to 9 until the desired result is obtained.
Press Return.
The screen returns to the Staple Pitch Adjustment Menu screen.
Pitch at two locations on the front edge for 4-position staple
Adjust the pitch at two locations on the front edge for 4-position staple in Saddle Stitcher SD-513.
Objects of Adjustment: Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm)
NOTICE
If a numeric value is specified for Offset for All Size, it is applied to all paper sizes. With a specific paper size selected,the set value becomes the sum of the entered value and the value previously specified for Offset for All Size.
Press Adjustment on the MACHINE screen to display the Adjustment Menu screen.
Press Finisher Adjustment, Saddle Stitcher Adjustment, Staple Pitch Adjustment, and 4 Position Staple(Front 2) in sequence.
Select the size to be adjusted.
Press Print Mode.
Load the paper with the size to be adjusted, then select that tray.
Press Start on the control panel.
A sample pattern will be output.
For the paper size, check the pitch at two locations on the front edge for 4-position staple.
If any adjustment is required, press Exit PrintMode to return to the Staple Pitch Adjustment screen.
Use the touch panel keypad to enter the set value.
supplementary explanationUse +/- to specify the value to be positive or negative.
supplementary explanationPress Set to change the Current Value.
supplementary explanationAdjustment Range: -10 (To shorten) to +10 (To lengthen) (1 step = 1.0 mm)
Repeat steps 4 to 9 until the desired result is obtained.
Press Return.
The screen returns to the Staple Pitch Adjustment Menu screen.
Pitch at two locations on the rear edge for 4-position staple
Adjust the pitch at two locations on the rear edge for 4-position staple in Saddle Stitcher SD-513.
Objects of Adjustment: Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm)
NOTICE
If a numeric value is specified for Offset for All Size, it is applied to all paper sizes. With a specific paper size selected,the set value becomes the sum of the entered value and the value previously specified for Offset for All Size.
Press Adjustment on the MACHINE screen to display the Adjustment Menu screen.
Press Finisher Adjustment, Saddle Stitcher Adjustment, Staple Pitch Adjustment, and 4 Position Staple(Rear 2) in sequence.
Select the size to be adjusted.
Press Print Mode.
Load the paper with the size to be adjusted, then select that tray.
Press Start on the control panel.
A sample pattern will be output.
For the paper size, check the pitch at two locations on the rear edge for 4-position staple.
If any adjustment is required, press Exit PrintMode to return to the Staple Pitch Adjustment screen.
Use the touch panel keypad to enter the set value.
supplementary explanationUse +/- to specify the value to be positive or negative.
supplementary explanationPress Set to change the Current Value.
supplementary explanationAdjustment Range: -10 (To shorten) to +10 (To lengthen) (1 step = 1.0 mm)
Repeat steps 4 to 9 until the desired result is obtained.
Press Return.
The screen returns to the Staple Pitch Adjustment Menu screen.