Adjustment Items

[Quality Adjustment]

Adjustment item and description

Objects/range of adjustment

01 Package Color Auto Adj.

This item is displayed on the machine mounted with Integrated Color Care Unit IQ-501.

Automatically adjust colors collectively.

-

02 Package Color Manual Adj.

Manually adjust color adjustment items collectively.

-

03 Density Balance Auto. Adj.

Perform the density balance adjustment using the scan function.

-

04 Maximum Density Adjustment

Adjust the maximum density for each of Y, M, C, and K colors. The machine will start the Gamma Automatic Adjustment after you change the maximum density. When the Gamma Automatic Adjustment is completed, proceed to the calibration with the image controller. Be sure to perform Color Density Manual Control after changing the maximum density.

Yellow: -10 (Light) to +10 (Dark)

Magenta: -10 (Light) to +10 (Dark)

Cyan: -10 (Light) to +10 (Dark)

Black: -10 (Light) to +10 (Dark)

05 Max. Density Auto Adj.

Max. Density Auto Adj. (RU) is displayed instead when Integrated Color Care Unit IQ-501 is not mounted on the machine.

Automatically print and scan charts and then adjust the maximum density for each of Y, M, C, and K colors. When this adjustment is completed, proceed to the calibration with the image controller. Be sure to perform Color Density Manual Control after changing the maximum density.

06 Color Density Control

Make settings for controlling the color density of output paper.

07 Periodical Both Sides Adj.

This item is displayed on the machine mounted with Integrated Color Care Unit IQ-501.

Configure settings for the periodical both-side adjustment.

Periodical Both Sides Adj.: ON or OFF

Adjustment Interval: 100 to 9,999 sheets

Deviation Check: ON or OFF

Specified Value: 0.5 to 10.0 mm

[Machine Adjustment]

Adjustment item and description

Objects/range of adjustment

01 Printer Adjustment

01 Restart Timing Adjustment

Adjust the image position of lead edge in paper feed direction in the printer engine.

Prerequisite: FD-Mag. Adjustment is completed.

Objects of adjustment:

Restart Timing (Tray 1 to Tray 9), Restart Timing (Back), Tray Large Plain Offset, Tray Large Thick Offset, Tray Small Plain Offset, Tray Small Thick Offset, Large Plain Offset (ADU), Large Thick Offset (ADU), Small Plain Offset (ADU), Small Thick Offset (ADU)

Adjustment Range:

-60 (Lower) to +60 (Higher)

(1 step = 0.1 mm)

02 Centering Adjustment

Adjust the image position in the crosswise direction of the printer engine.

Prerequisite: CD-Mag. Adjustment is completed.

Objects of adjustment:

Tray 1 to Tray 9, ADU, Tray1 Large Size Offset to Tray9 Large Size Offset, Tray1 Small Size Offset to Tray9 Small Size Offset, Large Plain Offset (ADU), Large Thick Offset (ADU), Small Plain Offset (ADU), Small Thick Offset (ADU), 8.5 5.5 Plain Offset (ADU), 8.5 5.5 Thick Offset (ADU)

Adjustment Range:

-40 (Front) to +40 (Back)

(1 step = 0.1 mm)

03 FD-Mag. Adjustment

Adjust the magnification in paper feed direction in the printer engine.

Objects of adjustment:

Printer FD-Mag.

Adjustment Range:

-100 (Short) to +100 (Long)

(1 step = 0.01%)

Objects of adjustment:

Tray 1 Offset (ADU) to Tray 9 Offset (ADU)

Adjustment Range:

-80 (Short) to +20 (Long)

(1 step = 0.01%)

04 CD-Mag. Adjustment

Adjust the magnification in crosswise direction in the printer engine.

Objects of adjustment:

Printer CD-Mag., Tray 1 Offset (ADU) to Tray 9 Offset (ADU)

Adjustment Range:

-100 (Short) to +100 (Long)

(1 step = 0.01%)

02 Scan Adjustment

01 Restart Timing Adjustment

Adjust the scan starting position when scanning the original on the original glass.

Prerequisite: FD-Mag. Adjustment is completed.

Adjustment Range:

-30 (Image Slow) to +30 (Image Fast)

(1 step = 0.1 mm)

02 Centering Adjustment

Adjust the image position in the crosswise direction when scanning the original on the original glass.

Prerequisite: Printer Centering Adjustment is completed.

Objects of adjustment:

Orig. Glass Centering

Adjustment Range:

-57 (Back) to +57 (Front)

(1 step = 0.1 mm)

03 FD-Mag. Adjustment

Adjust the magnification in feed direction when scanning the original on the original glass.

Prerequisite: Printer FD-Mag. Adjustment is completed.

Adjustment Range:

990 (Short) to 1010 (Long)

(1 step = 0.001)

04 CD-Mag. Adjustment

Adjust the magnification in the crosswise direction when scanning the original from the original glass.

Prerequisite: Printer CD-Mag. Adjustment is completed.

Adjustment Range:

990 (Short) to 1010 (Long)

(1 step = 0.001)

[Execute Adjust Operation]

Adjustment item and description

Objects/range of adjustment

Select a quality correction item and adjust the quality for your purpose.

Gamma Automatic Adj., Color Registration Adj., Toner Refresh Mode1, Toner Refresh Mode2, Fusing Refresh Mode, Charging Cleaning Mode, Drum Refresh Mode

[Finisher Adjustment] (Finisher FS-532)

This menu item is displayed and can be set on the machine mounted with Finisher FS-532.

Adjustment item and description

Objects/range of adjustment

01 Staple Finisher Adjustment

01 Staple Finisher(Main) Adj.

01 Exit Guide Paper Width Adj.

Adjust the exit guide alignment pitch to be used by the staple finisher.

Make adjustment if output paper stack on main tray is uneven in straight delivery.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 13 19 short edge feed, B5 short edge feed, A6 short edge feed / Postcard, SRA4 long edge feed, B6 short edge feed, 16K short edge feed, Custom (380 to 488 mm, Custom (220 to 379 mm), Custom (139 to 219 mm)

Adjustment Range:

-50 (Wide) to +50 (Narrow) (1 step = 0.1 mm)

02 Upper Gripper Operation

Select the upper gripper operation for main tray delivery exit.

Auto, ON, OFF

03 Output Alignment Operation

Select operation for output alignment.

Auto, ON, OFF

04 Staple Paper Width Adj.

Adjust the board alignment width of the staples in the staple finisher.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 13 19 short edge feed, SRA4 long edge feed, 16K short edge feed, Custom (380 to 488 mm, Custom (220 to 379 mm), Custom (139 to 219 mm)

Adjustment Range:

-20 (Wide) to +20 (Narrow) (1 step=0.1 mm)

05 FD Alignment Plate Adj.

Adjust the vertical alignment fitting for staples in the staple finisher.

Objects of adjustment:

Offset for All Sizes, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, 9 11 long edge feed, Custom (139 to 230 mm)

Adjustment Range:

-50 (Wide) to +50 (Narrow) (1 step = 0.1 mm)

06 Staple Position Adjustment

Adjust 2 position staple pitch and corner staple positions in the staple finisher.

Objects of adjustment:

2 Position Pitch (120 mm), 2 Position Pitch (140 mm), 2 Position Pitch (165 mm), Rear Diagonal

Adjustment Range:

-5 (Narrow) to +5 (Wide) (1 step = 1 mm)

Adjustment Range:

Rear Parallel, Front Parallel

Adjustment Range:

-3 (Narrow) to +3 (Wide) (1 step = 1 mm)

07 Rewind Paddle Descent Adj.

Adjust rewind paddle descent.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 13 19 short edge feed, SRA4 long edge feed, 16K short edge feed, Custom (380 to 488 mm, Custom (220 to 379 mm), Custom (139 to 219 mm)

Adjustment Range:

-10 (Little) to +10 (Much) (1 step = 0.2 mm)

08 Rewind Function Operation

Select operation for the rewind paddle.

Auto, ON, OFF

02 Staple Finisher(Fold) Adj.

This menu item is to be displayed and become configurable on Finisher FS-532 mounted with Saddle Stitcher SD-510.

01 Fold&Staple Paper Width Adj.

Adjust pitch of alignment plate in Saddle Stitcher SD-510 if half-folded or multi tri-folded paper show misalignment in the crosswise direction to paper feeding.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, 13 19 short edge feed, Custom (380 to 488 mm), Custom (240 to 379 mm)

Adjustment Range:

-50 (Narrow) to +50 (Wide) (1 step = 0.1 mm)

02 Fold&Staple Pitch Adjustment

Adjust staple pitch in Saddle Stitcher SD-510. Make this adjustment if staple pitch is not within the allowance range.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, 13 19 short edge feed, Custom (380 to 488 mm), Custom (240 to 379 mm)

Adjustment Range:

-300 (Narrow) to +300 (Wide) (1 step = 0.1 mm)

03 Fold&Staple Fold Position

Adjust half-fold position of fold & staple function in Saddle Stitcher SD-510. Make this adjustment if half-fold position is not within the specified range.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8. 5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, 13 19 short edge feed, Custom (380 to 488 mm), Custom (240 to 379 mm)

Adjustment Range:

-50 (Extend) to +50 (Shorten) (1 step = 0.1 mm)

04 Fold&Staple Staple Position

Adjust staple position in Saddle Stitcher SD-510.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, 13 19 short edge feed, Custom (380 to 488 mm), Custom (240 to 379 mm)

Adjustment Range:

-50 (Extend) to +50 (Shorten) (1 step = 0.1 mm)

05 Half-Fold Fold Position Adj.

Adjust half-fold position of fold function in Saddle Stitcher SD-510.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, 13 19 short edge feed, Custom (380 to 488 mm), Custom (240 to 379 mm)

Adjustment Range:

-50 (Extend) to +50 (Shorten) (1 step = 0.1 mm)

06 Tri-Fold Adjustment

01 Tri-Fold Position Adjustment

Adjust Fold 1 and Fold 2 positions for multi tri-folding in Saddle Stitcher SD-510.

Make this adjustment if each fold position for tri-folding is not within the allowance range.

Objects of adjustment:

8.5 11 short edge feed, A4 short edge feed, 16K short edge feed

Adjustment Range:

Fold 1: -50 (Extend) to +50 (Shorten) (1 step = 0.1 mm)

Fold 2: -50 (Shorten) to +50 (Extend) (1 step = 0.1 mm)

02 Double Fold Plate Adjustment

Adjust double fold plate in saddle stitcher.

Make the insertion deeper if the Fold 2 misalignment is large.

Objects of adjustment:

8.5 11 short edge feed, A4 short edge feed, 16K short edge feed

Adjustment Range:

-50 (Shallow) to +50 (Deep) (1 step = 0.1 mm)

07 Half-Fold Strength Adj.

To suppress the opening of booklets, increase the roller pressure time.

- You cannot adjust the strength to fold booklets.

- Long pressure time causes less productivity.

Adjustment Range:

(Additional time) 0 to +10 (1 step = 1 sec)

03 Staple Finisher(Punch) Adj.

This menu item is to be displayed and configurable on Finisher FS-532 mounted with Punch Kit PK-522.

01 Registration Adjustment

If the punch position is not parallel to the paper edge, control the paper curl and wrinkle by adjusting the paper loop amount of the registration roller.

Adjustment Range:

-50 (Short) to +50 (Long) (1 step = 0.1 mm)

02 Horizontal Position Adj.(FD)

Adjust the distance between the edge of the printed paper and the center of punch holes.

Objects of adjustment:

Offset for All Size, A3 short edge feed, A4 long edge feed, A4 short edge feed, SRA4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 8.5 14 short edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 9 11 long edge feed, B5 short edge feed

Adjustment Range:

-50 (Far) to +50 (Close) (1 step = 0.1 mm)

03 Vertical Position Adj.(CD)

Adjust the misalignment in center positions of paper and punch holes for each paper size.

Objects of adjustment:

Offset for All Size, A3 short edge feed, A4 long edge feed, A4 short edge feed, SRA4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 8.5 14 short edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 9 11 long edge feed, B5 short edge feed

Adjustment Range:

-50 (Forward) to +50 (Backward) (1 step = 0.1 mm)

04 Staple Finisher(PI) Adj.

This menu item is to be displayed and configurable on Finisher FS-532 mounted with Post Inserter PI-502.

01 PI Registration Adjustment

When paper fed from the upper or lower tray of Post Inserter PI-502 has skew or wrinkle, or causes paper jam, adjust the paper loop of the registration roller.

Objects of adjustment:

PI Upper Tray, PI Lower Tray

Adjustment Range:

[Finisher Adjustment] (Output Tray OT-510)

This menu item is displayed and can be set on the machine mounted with Output Tray OT-510.

Adjustment item and description

Objects/range of adjustment

01 Staple Finisher Adjustment

01 Staple Finisher(Main) Adj.

01 Exit Guide Paper Width Adj.

Adjust the exit guide alignment pitch to be used by the staple finisher.

Make adjustment if output paper stack on main tray is uneven.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 13 19 short edge feed, B5 short edge feed, A6 short edge feed / Postcard, SRA4 long edge feed, B6 short edge feed, 16K short edge feed, Custom (380 to 488 mm, Custom (220 to 379 mm), Custom (139 to 219 mm)

Adjustment Range:

-50 (Wide) to +50 (Narrow) (1 step = 0.1 mm)

02 Upper Gripper Operation

Select the upper gripper operation for main tray delivery exit.

Auto, ON, OFF

03 Output Alignment Operation

Select operation for output alignment.

Auto, ON, OFF

[Finisher Adjustment] (Folding Unit FD-503)

This menu item is to be displayed and allowed on the machine mounted with Folding Unit FD-503.

Adjustment item and description

Objects/range of adjustment

02 Multi Folder Adjustment

01 Multi Folder(Punch) Adj.

01 Paper Width Adjustment

Adjust the misalignment of punch hole positions.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, A4 long edge feed, A5 short edge feed, B5 long edge feed, A5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 9 11 long edge feed

Adjustment Range:

-20 (To reduce the randomness) to +20 (To reduce the tilts)

(1 step = 0.1 mm)

02 Punch Vertical Position Adj.

01 2-Hole Punch

Adjust the vertical position of punch holes made by the folding unit.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, A4 long edge feed, A5 short edge feed, B5 long edge feed, A5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 9 11 long edge feed

Adjustment Range:

-40 (To move to the center) to +40 (To move to the edge)

(1 step = 0.1 mm)

02 3-Hole Punch

Adjust the vertical position of punch holes made by the folding unit.

Adjustment Range:

Offset for All Size, A3 short edge feed, B4 short edge feed, A4 long edge feed, B5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 11 long edge feed, 8K short edge feed, 16K long edge feed, 9 11 long edge feed

Adjustment Range:

-40 (To move to the center) to +40 (To move to the edge)

(1 step = 0.1 mm)

02 4-Hole Punch

Adjust the vertical position of punch holes made by the folding unit.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, A4 long edge feed, B5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 11 long edge feed, 8K short edge feed, 16K long edge feed, 9 11 long edge feed

Adjustment Range:

-40 (To move to the center) to +40 (To move to the edge)

(1 step = 0.1 mm)

02 Multi Folder(Fold) Adj.

01 Half-Fold Position Adj.

Adjust the folded position for half-fold.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range:

-50 (To shorten the top face) to +50 (To lengthen the top face)

(1 step = 0.1 mm)

02 Z-Fold Position Adj.

Adjust the fold positions for Z-folding.

Adjust Fold 1 and Fold 2 in this order.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range:

Fold 1: -50 (To narrow) to +50 (To widen)

(1 step = 0.1 mm)

Fold 2: -50 (To narrow) to +50 (To widen)

(1 step = 0.1 mm)

03 Tri-Fold-in Pos. Adj.

Adjust the fold positions for tri-fold-in.

Adjust Fold 1 and Fold 2 in this order.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range:

Fold 1: -50 (To narrow) to +50 (To widen)

(1 step = 0.1 mm)

Fold 2: -50 (To narrow) to +50 (To widen)

(1 step = 0.1 mm)

04 Tri-Fold-out Pos. Adj.

Adjust the fold positions for tri-fold-out.

Adjust Fold 1 and Fold 2 in this order.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range:

Fold 1: -50 (To widen) to +50 (To narrow)

(1 step = 0.1 mm)

Fold 2: -50 (To narrow) to +50 (To widen)

(1 step = 0.1 mm)

05 Double Parallel Pos. Adj.

Adjust the fold positions for double parallel folding.

Adjust Fold 1 and Fold 2 in this order.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range:

Fold 1: -50 (To narrow) to +50 (To widen)

(1 step = 0.1 mm)

Fold 2: -50 (To narrow) to +50 (To widen)

(1 step = 0.1 mm)

06 Gate Position Adj.

Adjust the gate position.

Adjust Fold 1, Fold 2 and Fold 3 in this order.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range:

Fold 1: -50 (To narrow) to +50 (To widen)

(1 step = 0.1 mm)

Fold 2: -50 (To widen) to +50 (To narrow)

(1 step = 0.1 mm)

Fold 3: -50 (To narrow) to +50 (To widen)

(1 step = 0.1 mm)

[Finisher Adjustment] (Large Capacity Stacker LS-506)

This menu item is to be displayed and allowed on the machine mounted with Large Capacity Stacker LS-506.

Adjustment item and description

Objects/range of adjustment

03 Stacker Adjustment

01 Paper Width Adjustment

Adjust the position of adjustment plates if output sheets show misalignment in crosswise direction on the stacker tray.

Objects of adjustment:

Stacker No. 1, Stacker No. 2

Adjustment Range:

-20 (To reduce the dispersion) to +20 (To reduce the distortion)

(1 step = 0.1 mm)

02 Paper Length Adjustment

Adjust the position of the stopper if output sheets show misalignment in paper feed direction on the stacker tray.

Objects of adjustment:

Stacker No. 1, Stacker No. 2

Adjustment Range:

-20 (To reduce the dispersion) to +20 (To reduce the distortion)

(1 step = 0.1 mm)

[Finisher Adjustment] (Saddle Stitcher SD-506)

This menu item is to be displayed and allowed on the machine mounted with Saddle Stitcher SD-506.

Adjustment item and description

Objects/range of adjustment

04 Saddle Stitcher Adjustment

01 Fold Paper Width Adj.

Adjust the width of adjustment plates if half-folded or tri-folded sheets show misalignment.

Adjustment Range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 463 mm), Custom (257 to 379 mm)

Adjustment Range:

-50 (To reduce the misalignment) to +50 (To reduce the distortion)

(1 step = 0.1 mm)

02 Half-Fold Position Adj.

Adjust the folded position for half-fold.

Adjustment Range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 463 mm), Custom (257 to 379 mm)

Adjustment Range:

-50 (To shorten the top face) to +50 (To lengthen the top face)

(1 step = 0.1 mm)

03 Staple Paper Width Adj.

Adjust the width of adjustment plates of the saddle stitcher to be used in Staple mode.

Adjustment Range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 463 mm), Custom (257 to 379 mm)

Adjustment Range: -20 (To reduce the dispersion) to +20 (To reduce the distortion)

(1 step = 0.1 mm)

04 Staple Center Position

Adjust the center position of staples determined by the saddle stitcher.

Prerequisite: Staple paper width adjustment is completed.

Adjustment Range:

-20 (To move closer to paper center (fold)) to +20 (To move away from paper center (fold))

(1 step = 0.1 mm)

05 Staple Pitch Adjustment

Adjust the staple pitch determined by the saddle stitcher.

Adjustment Range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 463 mm), Custom (257 to 379 mm)

Adjustment Range:

-20 (To shorten) to +20 (To lengthen)

(1 step = 1.0 mm)

06 Trimming Adjustment

Adjust the trimming width. The trimming width should be more than 2.0 mm, otherwise the trimming operation may not performed properly.

Adjustment Range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 463 mm), Custom (257 to 379 mm)

Adjustment Range:

-400 (To narrow) to +400 (To widen)

(1 step = 0.1 mm)

07 Tri-Fold Position Adj.

Adjust the folded positions in Tri-Fold mode.

Adjust Fold 1 and Fold 2 in this order.

Adjustment Range:

Offset for All Size, A4 short edge feed, 8.5 11 short edge feed

Adjustment Range:

Fold 1: -100 (To widen) to +100 (To narrow)

(1 step = 0.1 mm)

Fold 2: -100 (To narrow) to +100 (To widen)

(1 step = 0.1 mm)

08 Trimmer Receiver Adj.

Frequent trimming operations may cause damage to the receiver, resulting in trimming failures. Move the receiver automatically or manually.

*Trimmer Receiver Adj. is not displayed by default. To use this setting, please contact your service representative.

Objects of Adjustment: Trim Count

Adjustment Range: 700 times, 500 times, 300 times

Objects of adjustment: Move Pitch

Adjustment Range: 1.0 mm, 1.5 mm, 2.0 mm

[Finisher Adjustment] (Saddle Stitcher SD-513)

This menu item is to be displayed and allowed on the machine mounted with Saddle Stitcher SD-513.

04 Saddle Stitcher Adjustment

01 Fold Paper Width Adj.

Adjust the width of adjustment plates if half-folded or tri-folded sheets show misalignment.

Adjustment Range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, PI Paper, Custom (380 to 488 mm), Custom (257 to 379 mm), 13 19 short edge feed

Adjustment Range:

-50 (To reduce the misalignment) to +50 (To reduce the distortion)

(1 step = 0.1 mm)

02 Fold Skew Adjustment

Adjust the skew of the folding line.

Objects of Adjustment: Single-Fold, Multi-Fold

Adjustment Range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, PI Paper, Custom (380 to 488 mm), Custom (257 to 379 mm), 13 19 short edge feed

Adjustment Range:

-50 (To weaken) to +50 (To strengthen)

(1 step = 0.1 mm)

03 Half-Fold Position Adj.

Adjust the folded position for half-fold.

Adjustment Range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm), 13 19 short edge feed

Adjustment Range:

-50 (To shorten the top face) to +50 (To lengthen the top face)

(1 step = 0.1 mm)

04 Tri-Fold Position Adj.

Adjust the folded positions in Tri-Fold mode.

Adjust Fold 1 and Fold 2 in this order.

Adjustment Range:

Offset for All Size, A4 short edge feed, 8.5 11 short edge feed

Adjustment Range:

Fold 1: -100 (To widen) to +90 (To narrow)

(1 step = 0.1 mm)

Fold 2: -50 (To widen) to +50 (To narrow)

(1 step = 0.1 mm)

05 Crease Position Adjustment

Adjust the crease position.

01 Half-Fold Crease Position

Move the half-fold crease position.

Adjustment Range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm), 13 19 short edge feed

Adjustment Range:

-20 (To shorten) to +20 (To lengthen)

(1 step = 0.1 mm)

02 Tri-Fold Crease Position

Move the tri-fold crease position.

Adjustment Range:

Fold 1, Fold 2: Offset for All Size, A4 short edge feed, 8.5 11 short edge feed

Adjustment Range:

-20 (To shorten) to +20 (To lengthen)

(1 step = 0.1 mm)

03 PB Cover Crease Position

Move the perfect binding cover crease position.

Adjustment Range:

Crease 1, Crease 2: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm), 13 19 short edge feed

Adjustment Range:

-20 (To shorten) to +20 (To lengthen)

(1 step = 0.1 mm)

06 Staple Paper Width Adj.

Adjust the width of adjustment plates of the saddle stitcher to be used in Staple mode.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm), 13 19 short edge feed

Adjustment Range: -20 (To reduce the dispersion) to +20 (To reduce the distortion)

(1 step = 0.1 mm)

07 Staple Center Position

Adjust the center position of staples determined by the saddle stitcher.

Prerequisite: Staple paper width adjustment is completed.

01 2 Position Staple

Adjust the center position for 2-position staple.

Adjustment Range:

-20 (To move closer to rear edge) to +20 (To move closer to front edge)

(1 step = 0.1 mm)

02 4 Position Staple(Front 2)

Adjust the center position at two locations on the front edge for 4-position staple.

Objects of adjustment:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm)

Adjustment Range: -100 (To move closer to rear edge) to +100 (To move closer to front edge)

(1 step = 0.1 mm)

02 4 Position Staple(Rear 2)

Adjust the center position at two locations on the rear edge for 4-position staple.

Objects of adjustment:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm)

Adjustment Range: -100 (To move closer to rear edge) to +100 (To move closer to front edge)

(1 step = 0.1 mm)

08 Staple Pitch Adjustment

Adjust the staple pitch determined by the saddle stitcher.

01 2 Position Staple

Adjust the pitch for 2-position staple.

Adjustment Range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm), 13 19 short edge feed

Adjustment Range:

-20 (To shorten) to +20 (To lengthen)

(1 step = 1.0 mm)

02 4 Position Staple(Front 2)

Adjust the pitch at two locations on the front edge for 4-position staple.

Adjustment Range:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm)

Adjustment Range:

-10 (To shorten) to +10 (To lengthen)

(1 step = 1.0 mm)

02 4 Position Staple(Rear 2)

Adjust the pitch at two locations on the rear edge for 4-position staple.

Adjustment Range:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm)

Adjustment Range:

-10 (To shorten) to +10 (To lengthen)

(1 step = 1.0 mm)

09 Staple Offset Adjustment

Adjust the misalignment between the stapling positions and folding line.

Adjustment Range:

-10 (To move leftward) to +10 (To move rightward)

(1 step = 0.1 mm)

10 Staple Tip Adjustment

Change the staple leg shape.

Adjustment Range:

-9 (To round the staple leg) to +9 (To level the staple leg)

(1 step = 1 msec)

11 Flattening a Fold (Strength)

Adjust the spine shape while changing the strength to form the book spine.

Adjustment Range:

-20 (To decreace the force) to +20 (To increace the force)

(1 step = 0.1 mm)

12 Flattening a Fold (Freq.)

Adjust the number of roller reciprocation times to form the book spine.

Adjustment Range:

-5 (To decrease) to +5 (To increase)

(1 step = 1 roller reciprocation operation)

13 Parallel Trimming Adjustment

Adjust the levelness between the trimming line and cut edge.

Adjustment Range:

Front, rear

Adjustment Range:

0 (To narrow) to +30 (To widen)

(1 step = 0.1 mm)

14 Fore-edge Trimming Adj.

Adjust the trimming width.

The trimming width should be more than 5 mm, otherwise the trimming operation may not performed properly.

Adjustment Range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom (380 to 488 mm), Custom (257 to 379 mm), 13 19 short edge feed

Adjustment Range:

-400 (To narrow) to +400 (To widen)

(1 step = 0.1 mm)

15 2-Side Slitting Adjustment

Adjust the 2-side slitting.

Adjustment Range:

Front, rear

Adjustment Range:

-10 (To narrow) to +10 (To widen)

(1 step = 0.1 mm)

16 2-Side Slit Finishing Adj.

Change the 2-side trimming speed to adjust skew and napping conditions.

Adjustment Range:

61 g/m2 or Less, 62 g/m2 or More

Adjustment Range:

-4 (Slow) to +4 (Fast)

(1 step = 5 mm/sec.)

17 Trimmer Receiver Adj.

Frequent trimming operations may cause damage to the receiver, resulting in trimming failures. Move the receiver automatically or manually.

*Trimmer Receiver Adj. is not displayed by default. To use this setting, please contact your service representative.

Objects of Adjustment: Trim Count

Adjustment Range: 700 times, 500 times, 300 times

Objects of adjustment: Move Pitch

Adjustment Range: 1.0 mm, 1.5 mm, 2.0 mm

[Finisher Adjustment] (Perfect Binder PB-503)

This menu item is to be displayed and allowed on the machine mounted with Perfect Binder PB-503.

Adjustment item and description

Objects/range of adjustment

05 Perfect Binder Adjustment

01 Sub Compile CD Width Adj.

Adjust misalignment or distortion in the crosswise direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-20 (To reduce the distortion) to +20 (To reduce the misalignment)

(1 step = 0.1 mm)

02 Clamp CD Width Adjustment

Adjust misalignment or distortion in the crosswise direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-20 (To reduce the distortion) to +20 (To reduce the misalignment)

(1 step = 0.1 mm)

03 Clamp FD Position Adj.

Adjust misalignment or distortion in the paper feed direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-20 (To reduce the distortion) to +20 (To reduce the misalignment)

(1 step = 0.1 mm)

04 Glue Start Position

Adjust the position to start gluing on the body. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Ahead: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, Custom (220 to 379 mm), Custom (148 to 219 mm)

Back: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-128 (To increase) to +127 (To decrease)

(1 step = 0.1 mm)

05 Glue Finish Position

Adjust the position to finish gluing on the body. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Ahead: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, Custom (220 to 379 mm), Custom (148 to 219 mm)

Back: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-128 (To decrease) to +127 (To increase)

(1 step = 0.1 mm)

06 Cover Lead Edge Adj.

Adjust the position of the lead edge of the left cover sheet. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

PB tray: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, Custom (220 to 379 mm), Custom (148 to 219 mm)

Except PB Tray: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-128 (To move closer to the body) to +127 (To move further from the body)

(1 step = 0.1 mm)

07 Cover Trimming Adjustment

Adjust the trimming width of the right cover sheet. To align the lead edges of left and right cover pages, be sure to perform Cover Lead Edge Adjustment in advance.

Objects of adjustment:

Perfect Binder Tray, Except PB Tray

Adjustment Range:

-128 (To narrow) to +127 (To widen)

(1 step = 0.1 mm)

08 Cover Up/Down CD Width Adj.

Adjust the misalignment between the cover sheet and body.

Objects of adjustment:

Perfect Binder Tray, Except PB Tray

Adjustment Range:

-20 (To reduce the distortion) to +20 (To reduce the misalignment)

(1 step = 0.1 mm)

09 Spine Corner Forming Pos.

Adjust the form of cover paper.

Objects of adjustment:

Up/Down Forward Adj. (Front), Up/Down Rear Adj. (Rear)

Adjustment Range:

-128 (To convex) to +127 (To concave)

(1 step = 0.1 mm)

10 Temperature Adjustment

Glue Tank -Low:

Adjust the temperature to control the tank heater.

Low temperature: Increases glue viscosity.

High temperature: Decreases glue viscosity.

Glue Apply Roller:

Adjust the temperature to control the roller heater. This also supports heating of the glue.

Low temperature: Increases glue viscosity.

High temperature: Decreases glue viscosity.

Objects of Adjustment: Glue Tank -Low

Initial: 185°C

Adjustment Range:

180°C (Down: viscosity increased) to 190°C (Up: viscosity decreased)

(1 step = 1°C)

Objects of adjustment: Glue Apply Roller

Initial: 165°C

Adjustment Range:

160°C (Down: viscosity increased) to 170°C (Up: viscosity decreased)

(1 step = 1°C)

[ADF Adjustment]

Adjustment item and description

Objects/range of adjustment

01 ADF Original Stop Pos. Adj.

Adjust the position to start scanning on the ADF and the image position in the crosswise direction.

Prerequisite: FD-Mag. Adjustment should be completed before adjusting the position to start scanning. Printer Centering Adjustment should be completed before adjusting the image position.

Objects of adjustment:

Restart Timing (Front), Restart Timing (Back)

Adjustment Range:

-40 (Image Fast) to +40 (Image Slow)
(1 step = 0.1 mm)

Objects of adjustment:

Centering (Front), Centering (Back)

Adjustment Range:

-44 (Front) to +44 (Back)
(1 step = 0.1 mm)

02 ADF Orig. Stop Pos. Auto

Automatically adjust the position to start scanning on the ADF and the image position in crosswise direction.

Prerequisite: FD-Mag. Adjustment should be completed before adjusting the position to start scanning. Printer Centering Adjustment should be completed before adjusting the image position.

Objects of adjustment:

Restart Timing (Front), Restart Timing (Back),
Centering (Front), Centering (Back)

03 FD-Mag. Adjustment

Adjust the magnification in paper feed direction when scanning on the ADF.

Prerequisite: Printer FD-Mag. Adjustment is completed.

Objects of adjustment:

ADF

Adjustment Range:

-20 (Short) to +20 (Long)
(1 step = 0.1%)

04 FD-Mag. Auto Adjustment

Automatically adjust the magnification in paper feed direction when scanning on the ADF.

Objects of adjustment:

ADF

05 Home Read Position Adj(Back)

Adjust the home position of the shading shaft to correct any image failure due to dirt on the shading shaft on the back side of the ADF.

Adjustment Range:

-4 to +4

(1 step = 1)

06 FD-Mag. Adjustment(Back)

Adjust the magnification in paper feed direction on the back side when scanning on the ADF.

Prerequisite: Printer FD-Mag. Adjustment is completed.

Objects of adjustment:

ADF

Adjustment Range:

(Short) -20 to +20 (Long)

(1 step = 0.1 %)

07 FD-Mag. Auto Adj.(Back)

Automatically adjust the magnification in paper feed direction on the back side when scanning on the ADF.

Objects of adjustment:

ADF

08 Main Scan Dir. Zoom(Back)

Adjust the magnification in crosswise direction on the back side when scanning on the ADF.

Prerequisite: Printer CD-Mag. Adjustment is completed.

Objects of adjustment:

ADF

Adjustment Range:

(Short) -10 to +10 (Long)

(1 step = 0.1 %)

09 Main ScanDir.Zoom Auto(Back)

Automatically adjust the magnification in crosswise direction on the back side when scanning on the ADF.

Objects of adjustment:

ADF

10 Original Tray Pre-rise Set.

Adjust the standby position of the Original feed tray on the ADF.

Original Tray Pre-rise: ON, OFF

Objects of adjustment: Paper tray standby position.

Adjustment Range: 1 to 7

Finisher Adjustment (Relay Unit RU-510)

This menu item is to be displayed and allowed on the machine mounted with Relay Unit RU-510.

Adjustment item and description

Objects/range of adjustment

01 Paper Width Adjustment

Align both ends of the output sheets in order to reduce the variation and misalignment of punch holes.

Adjustment range:

-20 (To reduce the randomness) to +20 (To reduce the tilts)

(1 step = 0.1 mm)

02 Paper Length Adjustment

Adjust the stop position for the lead edge of output sheets in order to reduce the variation and misalignment of punch holes.

Adjustment range:

-50 (To reduce the dispersion) to +50 (To reduce the tilts)

(1 step = 0.1 mm)

[PFU Air Assist Adjustment]*

Adjustment item and description

Objects/range of adjustment

Set the air assist setting for Paper Feed Unit PF-707m or Paper Feed Unit PF-711.

* This setting is not displayed by default. To use this setting, please contact your service representative.

Target Tray:

Tray 1, Tray 2, Tray 3, Tray 4, Tray 5, Tray 6, Tray 7, Tray 8, Tray 9

Setting Method:

Auto, Manual

Setting Range for Manual Adjustment:

Lead Edge Air Level Setting: 1 (Weak) to 9 (Strong)

Side Air Level Setting: OFF, 1 (Weak) to 9 (Strong)