The copy image is dirty

Is the Original glass dirty?

Clean the dirt off the Original glass

Cleaning the Original glass

Is the original dirty?

Clean the dirt off the original

-

Is the density adjustment appropriate?

Manually adjust the density for [Copy Density]

[Copy Density]

The copy image is faint

Is the density adjustment appropriate?

Adjust the density manually using [Copy Density]

[Copy Density]

Is the information display area of the [MACHINE] screen displaying a message informing you to replace the toner?

Replenish the toner

Replacing the Toner bottle

The copy image is not clear

Is the paper damp?

Replace the paper

Paper Loading and Settings

The positions of the staples have shifted by 90 degrees

Is Automatic Image Rotation activated?

Re-load the paper and make sure Automatic Image Rotation is not activated

Paper Loading and Settings

The output paper is not stacked uniformly, and the staple positions are not where they should be

Is the paper curling up?

Load the paper in the feed tray so that the front side faces down and the back side faces up

Paper Loading and Settings

The staple positions are not aligned

Is the paper curling up?

Change the paper curl direction and load the paper into the tray

Paper Loading and Settings

The Secondary (sub) tray output paper is out of alignment

Is the paper placed up against the edge of the Secondary (sub) tray?

Temporarily release the Secondary (sub) tray from its locked state, and allow Secondary (sub) tray to raise up

-

No side stitch stapling output, even though configured to output it

• Is the message [Pull out staple finisher stacker then, set staples in stapler] displayed in the message display area?

• Is the [Staple Cartridge] notification lamp on the [MACHINE] screen lit up red?

Pull out the Stacker from the Finisher, and replenish the staples for performing side stitch stapling

Replenishing Staples

• Is the message [Staple scrap box is full] displayed in the message display area?

• Is the [Staple Scrap Box] notification lamp on the [MACHINE] screen lit up red?

Pull out the Stacker from the Finisher, and dispose of the staple scraps

Displaying Help Messages

Does not perform Fold & Staple even though the relevant settings have been set on the Finisher with Saddle Stitcher SD-510 mounted

• Is the message [Pull out staple finisher stacker then, set staples in stapler] displayed in the message display area?

• Is the [Staple Cartridge] notification lamp on the [MACHINE] screen lit up red?

Pull out the Saddle unit from the Finisher, and replenish the staples for performing Fold & Staple

Replenishing Staples

Does not perform punching, even though the relevant settings have been set on the Finisher with Punch Unit PK-525 mounted

• Is the message [Scrap of punch kit is full Please empty scrap box] displayed in the message display area?

• Is the [Punch-Hole Scraps Box] notification lamp on the [MACHINE] screen lit up red?

Open the Finisher front door, pull out the Punch scrap box, and dispose of the punch scraps

Disposing of Trimming/Punching Scraps

Does not perform trimming even though the relevant settings have been set

Is the [SaddleStitcher Trim Scrap] notification lamp on the [MACHINE] screen lit up red?

Dispose of the SaddleStitcher SD-506 trimming scraps

Disposing of Trimming/Punching Scraps

Does not perform fore-edge trimming even though the relevant settings have been set

Is the [SD Trim Scrap Box] notification lamp on the [MACHINE] screen lit up red?

Dispose of the Saddle Stitcher SD-513 fore-edge trimming scraps

Disposing of Trimming/Punching Scraps

Does not perform 2-side slitting even though the relevant settings have been set

Is the [SD Slit Scrap Box] notification lamp on the [MACHINE] screen lit up red?

Dispose of the Saddle Stitcher SD-513 2-side slitting scraps

Disposing of Trimming/Punching Scraps

Does not perform perfect binding even though the relevant settings have been set

Is Perfect binder tray front door, Perfect binder tray front door, or Glue hopper cover open?

Make sure all of Perfect binder tray front door, Perfect binder tray front door, and Glue hopper cover are properly closed

-