Saving the Number of Copy Sheets

[Original > Output]

Select a combination of the original to be loaded (1-sided original or 2-sided original) and the copy method (1-sided copy or 2-sided copy).

If you have selected other than [1Sided > 1Sided], also specify [Binding Position] and [Original Direction].

[Binding Position]

Select the binding positions of the original and copy.

[No. of Originals]

Select the original binding position when a 2-sided original is loaded.

• [Auto]: The binding position is specified automatically. When the long side of the original is 11-11/16 inches (297 mm) or less, the binding position is set to the long side of the paper. When the long side of the original exceeds 11-11/16 inches (297 mm), the binding position is set to the short side of the paper.

• [Left Bind]: Select this option when the binding position is set to the left of the original.

• [Right Bind]: Select this option when the binding position is set to the right of the original.

• [Top Bind]: Select this option when the binding position is set to the top of the original.

[Output]

Select the binding position when printing on both sides of paper.

• [Auto]: The binding position of a copy is specified automatically. When the long side of the original is 11-11/16 inches (297 mm) or less, the binding position is set to the long side of the paper. When the long side of the original exceeds 11-11/16 inches (297 mm), the binding position is set to the short side of the paper.

• [Left Bind]: Select this option when setting the binding position to the left of a copy.

• [Right Bind]: Select this option when setting the binding position to the right of a copy.

• [Top Bind]: Select this option when setting the binding position to the top of a copy.

[Original Direction]

Specify the orientation of the loaded original.

[ON]/[OFF]

Select [ON] to specify Image Repeat.

[Image Repeat Setting]

Select the copy method on the paper.

• [With Margin]: Copy an original image including its edges repeatedly on a single sheet of paper. The number of times repeated is determined automatically according to the original and paper sizes, or zoom ratio.

• [Without Margin]: Copy an original image repeatedly as much as possible on a single sheet of paper. The images on the edge of the paper may be partially lost. The number of times repeated is determined automatically according to the original and paper sizes, or zoom ratio.

• [2/4/8 Repeat]: Copy an original image repeatedly for the registered number of times on a single sheet of paper. Images that do not fit the divided area will be partially lost.
  If you select [2 Repeat], you can specify the interval between images in units of 1/16 inch to 10 inches (0.1 mm to 250.0 mm) in [Repeat Interval].

[Scan Range]

Specify the scanning range (original size).

[ON]/[OFF]

Select [ON] to specify Card Shot.

[Original Size]

Specify the size of the card to copy by tapping [+]/[-] for the inch area, by tapping [+]/[-] or Keypad for the centimeter area. To display the Keypad, tap the input area for the numeral. From the [Registered Paper Size], you can recall a size previously stored and specify the size.

After you have entered the size, select a key in [Registered Paper Size], and tap [Register]. Then the size you have entered is registered in the memory. You can recall the registered size in the future.

[Registered Paper Size]

Displays the sizes registered in memory.

When you call a registered size from the memory, tap the key of the desired registration name, then tap [Recall].

[Layout]

Select the layout for arranging the front side and back side of the card on the paper from [Top/Bottom], [Left/Right (Top Half)], and [Left/Right].

[Zoom]

Select a zoom ratio for copying.

• [Full Size]: Copy by enlarging according to the paper size.

• [x1.0]: Copy with the same size as the card.

[Change registered size name]

Change the name of the key you selected in [Registered Paper Size].