[Multi Half Fold]
Overview
Configure the setting for Multi Half Fold paper.
The displayed screens and selectable setting items vary depending on the optional devices mounted on this system.
[Valid Object] cannot be changed in [All Sheets] because it is fixed.
NOTICE
- Saddle Stitcher SD-513 with Creaser Unit CR-101 mounted is required to set the [Crease].
- Saddle Stitcher SD-513 with Trimmer Unit TU-503 mounted is required to set the [(2)2-Side Slit].
NOTICE
Either one of the following options is required to set the [Multi Half Fold].
- Finisher FS-532 with Saddle Stitcher SD-510 mounted
- Finisher FS-541 with Saddle Stitcher SD-510 mounted
NOTICE
- Multi Half Fold sheets are output to the Bundle exit tray. Set the Extension tray of the bundle exit tray as preparation, and open the Stopper. Otherwise, the printed paper may drop down from the Bundle exit tray. Also, the full-load detection function may not work.
- When using easy-to-curl and thin paper for Multi Half Fold, print out so that paper is curled inside. Before printing a booklet, print only several sheets to the Secondary (sub) tray, and check the curl orientation. If the printed-out sheets are curled upward, paper is curled inward when a booklet is created.
Reference
- For details about [Multi Half Fold], refer to What Is [Multi Half]?.
Setting Items (With SaddleStitcher SD-506 Mounted)
Setting item | Description | ||
|---|---|---|---|
[Trim or Non Trim] |  | [Trimming] | Trims the fore edge. |
[Non Trimming] | Does not trim the fore edge. | ||
[Valid Object] | [Valid Object] cannot be changed in [All Sheets] because it is fixed. | ||
[Function OFF] | Turns the function off while maintaining the set information. | ||
Setting Items (With Saddle Stitcher SD-513 Mounted)
Setting item | Description | ||
|---|---|---|---|
[Print Side] | [Outside Print] | Places the print side outside with the paper folded. | |
[Inside Print] | Places the print side inside with the paper folded. | ||
[Crease] |  | [ON] | Only creases the covers. |
[OFF] | Does not crease. | ||
[(1)Fore-edgeTrim] | | [ON] | Trims the fore edge. |
[OFF] | Does not trim the fore edge. | ||
[(2)2-Side Slit] |  | [ON] | Slits both edges of the paper. [Slitting] and [Offset against Cover] are available. |
[OFF] | Does not slit both edges of the paper. | ||
[Valid Object] | [Valid Object] cannot be changed in [All Sheets] because it is fixed. | ||
[Function OFF] | Turns the function off while maintaining the set information. | ||
Setting Items (With Finisher FS-532 / Finisher FS-541 Mounted)
Setting item | Description | |
|---|---|---|
[Multi Half Fold] | [ON] | Multi half folds paper. |
[OFF] | Does not multi half fold paper. | |
[Valid Object] | [Valid Object] cannot be changed in [All Sheets] because it is fixed. | |
[Function OFF] | Turns the function off while maintaining the set information. | |
Setting Procedure (With Saddle Stitcher SD-513 Mounted)
Set [Slitting] and [Offset against Cover] for 2-Side Slit.
1
Press [ON] in [(2)2-Side Slit].
The setting screen is displayed.
2
Select [(1)] or [(2)] of [Slitting], and use the on-screen keypad to enter the slitting amount.
Range: 8.0 mm to 26.0 mm
Pressing [,]/[+] increases or decreases the numeric value in steps of 0.1 mm.
Use [+ / -] to set the plus or minus of the numeric value.
When the slitting amount is different between [(1)] and [(2)] by 10.0 mm or more, its value cannot be entered.
3
Select [Offset against Cover], and use the on-screen keypad to enter the slitting amount of the body for the cover.
Range: -1.0 mm to 1.0 mm
Pressing [,]/[+] increases or decreases the numeric value in steps of 0.1 mm.
4
Press [OK].
in the upper-right of a page, it turns into 
and is registered as a bookmark.