[Multi Tri-Fold]
Overview
Configure the setting to apply Multi Tri-Fold to the paper.
The displayed screens and selectable setting items vary depending on the optional devices mounted on this system.
[Valid Object] cannot be changed in [All Sheets] because it is fixed.
NOTICE
Either one of the following options is required when setting the [Multi Tri-Fold].
- SaddleStitcher SD-506
- Finisher FS-532 with Saddle Stitcher SD-510 mounted
- Finisher FS-541 with Saddle Stitcher SD-510 mounted
NOTICE
- Saddle Stitcher SD-513 with Creaser Unit CR-101 mounted is required to set the [Crease].
- Saddle Stitcher SD-513 with Trimmer Unit TU-503 mounted is required to set the [2-Side Slitting].
NOTICE
- Only 1 sheet is folded for creasing. It is not folded multiply.
- A misalignment may occur between the fold position and crease position depending on the paper weight. In such a case, adjust the crease position to suit the fold position. For details, refer to [Saddle Stitcher Adjustment] (Saddle Stitcher SD-513).
NOTICE
- Only 1 sheet is folded for slitting. It is not folded multiply.
- If [2-Side Slitting] is combined with Tri-Fold, wrinkles may occur depending on the paper type.
- If [2-Side Slitting] is combined with Tri-Fold and [Crease], the part near wrinkles may be broken. If wrinkles occur in either case, reduce the slitting amount, because wrinkles are easily formed when the slitting amount is 20 mm / 0.787" or more.
Reference
- For details about [Multi Tri-Fold], refer to What Is [Multi 3-Fold]?.
Setting Items (With SaddleStitcher SD-506 / Finisher FS-532 or Finisher FS-541 Mounted)
Setting item | Description | |
|---|---|---|
[Multi Tri-Fold] | [ON] | Multi tri-folds paper. |
[OFF] | Does not multi tri-fold paper. | |
[Valid Object] | [Valid Object] cannot be changed in [All Sheets] because it is fixed. | |
[Function OFF] | Turns the function off while maintaining the set information. | |
Setting Items (With Saddle Stitcher SD-513 Mounted)
Setting item | Description | ||
|---|---|---|---|
[Crease] |  | [ON] | Creases only the covers for Multi Tri-Fold. |
[OFF] | Does not crease. | ||
[2-Side Slitting] |  | [ON] | Slits both edges of the paper. [Slitting] and [Offset against Cover] are available. |
[OFF] | Does not slit both edges of the paper. | ||
[Valid Object] | [Valid Object] cannot be changed in [All Sheets] because it is fixed. | ||
[Function OFF] | Turns the function off while maintaining the set information. | ||
Setting Procedure
Set [Slitting] and [Offset against Cover] for 2-Side Slit.
1
Press [ON] in [2-Side Slitting].
The setting screen is displayed.
2
Select [(1)] or [(2)] of [Slitting], and use the on-screen keypad to enter the slitting amount.
Range: 8.0 mm to 26.0 mm
Pressing [,]/[+] increases or decreases the numeric value in steps of 0.1 mm.
Use [+ / -] to set the plus or minus of the numeric value.
When the slitting amount is different between [(1)] and [(2)] by 10.0 mm or more, its value cannot be entered.
3
Select [Offset against Cover], and use the on-screen keypad to enter the slitting amount of the body for the cover.
Range: -1.0 mm to 1.0 mm
Pressing [,]/[+] increases or decreases the numeric value in steps of 0.1 mm.
4
Press [OK].
in the upper-right of a page, it turns into 
and is registered as a bookmark.