Improving the Security of this Machine (For Administrators)

[IPsec Settings]

Specify parameters required for IPsec communication.

You can configure IKE (Internet Key Exchange), SA (Security Association), IPsec peer, or IPsec protocol settings.

[IKE Settings]

Configure settings required to create a common key for IPsec.

For details, refer to Here.

[IPsec SA Settings]

Configure SA (Security Association) required for encrypted communication.

For details, refer to Here.

[Peer]

Register the peer of this machine to use IPsec.

For details, refer to Here.

[Protocol Setting]

Specify a protocol used for IPsec communication.

For details, refer to Here.

[Enable IPsec]

Configure settings to enable use of IPsec on this machine. Also, specify the policy for IPsec communication. For details, refer to Here.

[Communication Check]

Select this option to confirm IPsec communication error logs.

For details, refer to Here.

[Enable]/[Disable]

Select whether to specify an IPv4 address that denies access to this machine.

[Disable] is specified by default.

[Set 1] to [Set 5]

Enter the range of IPv4 addresses that deny access using the following format.

• Entry example: "192.168.1.1 - 192.168.1.10"

• To allow access from a single IPv4 address, you can only enter the address in one side of the range.

[Enable]/[Disable]

Select whether to specify an IPv4 address that allows access to this machine.

[Disable] is specified by default.

[Set 1] to [Set 5]

Enter the range of IPv4 addresses that allow access using the following format.

• Entry example: "192.168.1.1 - 192.168.1.10"

• To allow access from a single IPv4 address, you can only enter the address in one side of the range.

[Enable]/[Disable]

Select whether to specify an IPv6 address that denies access to this machine.

[Disable] is specified by default.

[Set 1] to [Set 5]

Enter the IPv6 address and prefix length to specify the range of IPv6 addresses that deny access.

[Enable]/[Disable]

Select whether to specify an IPv6 address that allows access to this machine.

[Disable] is specified by default.

[Set 1] to [Set 5]

Enter the IPv6 address and prefix length to specify the range of IPv6 addresses that allow access.

[Synchronize IP Address]

For the IPv4 address, this option only permits access for the IPv4 address set to this machine, and the IPv4 addresses of which the high-order 3 bytes are the same.

Example: When the IPv4 address of this machine is set to "192.168.0.134", the range of IPv4 addresses that allow access is as follows.
192.168.0.0 to 192.168.0.255

For the IPv6 address, this option only permits access for the global unicast address (2000::/3). Also, this option only permits access for the IPv6 address set to this machine, and the IPv6 addresses of which the high-order 64 bits are the same.

Example: When the IPv6 address of this machine is set to "2345:1:2:3:4:5:6:7", the range of IPv6 addresses that allow access is as follows.
2345:1:2:3::0 to 2345:1:2:3:FFFF:FFFF:FFFF:FFFF

[Synchronize Subnet Mask]

For the IPv4 address, this option only permits access for IPv4 addresses that belong to the same network using the IPv4 address set to this machine and subnet mask.

If no subnet mask is set or "0.0.0.0" is specified, this option permits the IPv4 address set to this machine, and the IPv4 addresses each of which only the suffix is different. This results in the same operation as for [Synchronize IP Address].

Example: When the IPv4 address of this machine is set to "192.168.17.134" and the subnet mask is set to "255.255.252.0", the range of IPv4 addresses that allow access is as follows.
192.168.16.*** to 192.168.19.***

For the IPv6 address, this option only permits access for the global unicast address (2000::/3). Also, filtering is carried out using the global IPv6 address set to this machine and prefix.

If the prefix is not specified, filtering is carried out in the same way as when the 64-bit prefix is specified.

Example: When the IPv6 address of this machine is set to "2345:1:2:3:4:5:6:7" and Prefix is set to "/64", the range of IPv6 addresses that allow access is as follows.
2345:1:2:3::0 to 2345:1:2:3:FFFF:FFFF:FFFF:FFFF

[No Filtering]

Does not use the filtering function.

[Check Setting]

Displays a list of registered filters.

• [Details]: Displays the setting of the selected filter.

• [Delete]: Deletes the selected filter.

[Import]

Collectively imports multiple filters from a USB flash drive. This option is available to edit filters exported from the machine on the computer before importing them.

[Export]

Exports all the registered filters to a USB flash drive.

[Log settings]

Records a history of packets with receiving or sending denied by the packet filtering function.

• [Enable]/[Disable]: Select whether to record packet filtering logs. [Disable] is specified by default.

• [Save to External Memory]: Writes packet filtering logs to a USB flash drive. [Number of Lines]: Specify the number of logs to be written (default: [1000]). Tapping [Start] starts writing.

[ON]/[OFF]

Select whether to use IEEE802.1x authentication.

[OFF] is specified by default.

[Auth. Status]

Displays the status of IEEE802.1x authentication on this machine.

[Reset Job Settings]

Reset the current setting.

[Certificate Verification Level Settings]

To verify the certificate, select items to be verified.

• [Expiration Date]: Confirm whether the certificate is within the validity period. [Confirm] is specified by default.

• [CN]: Confirm whether CN (Common Name) of the certificate matches the server address. [Do Not Confirm] is specified by default.

• [Chain]: Confirm whether there is a problem in the certificate chain (certificate path). The chain is validated by referencing the external certificates managed on this machine. [Do Not Confirm] is specified by default.

[Limit]/[Do Not Limit]

Select whether to limit the recipient domain.

[Do Not Limit] is specified by default.

[Send Permission Setting]

Specify the domain to be permitted for the recipient.

Select a recipient domain key, then enter the IP address or domain name of the domain (using up to 255 bytes).

• Symbol "?" is recognized as any one character.

• Symbol "*" is recognized as any characters of 0 or more.

[Send Deny Setting]

Specify the domain to be denied for the recipient.

Select a recipient domain key, then enter the IP address or domain name of the domain (using up to 255 bytes).

• Symbol "?" is recognized as any one character.

• Symbol "*" is recognized as any characters of 0 or more.

[Limitation check of Shared address]

Check whether destinations with transmission disabled are included in the destinations registered on this machine.

[Administrator Password]

Change the administrator password of this machine.

For details, refer to Here.

[USB Enable Settings]

Specify whether to permit a function that requires the USB Port.

For details, refer to Here.

[Password Rules]

Configure whether to enable the password rules. Once you enable it, the number of characters and text types that are available for passwords is restricted. If necessary, change the minimum number of password characters.

For details, refer to Here.

[Quick IP Filtering]

Allows you to restrict the devices that can access this machine using the IP address (IPv4/IPv6). The range of IP addresses for which access is to be restricted is specified automatically.

For details, refer to Here.

[Web Setting]

Select whether to use Web Connection.

For details, refer to Here.

[Security Warning Display Setting]

Select whether to display the security warning screen if the administrator password remains set to the default or if password rules are not satisfied.

For details, refer to Here.

[Password]

Enter a new administrator password (using up to 64 characters).

[Password Confirmation]

Retype the new administrator password for confirmation.

[IWS Application]

Specify whether to allow the administrator password to be changed via the IWS application.

[Allow] is specified by default.

[Level 1]

Open up the following settings to the users.

• [Low Power Mode Settings]

• [Sleep Mode Settings]

• [Auto Zoom (Platen)]

• [Auto Zoom (ADF)]

• [Specify Default Tray when APS Off]

• [Tri-Fold Print Side]

• [Automatic Image Rotation]

[Level 2]

Open up the following settings to the users.

• Settings that are opened up to users in [Level 1]

• [Print/Fax Output Settings]

• [Output Tray Settings]

• [AE Level Adjustment]

• [Blank Page Print Settings]

• [Page Number Print Position]

• [Change E-Mail Address]

• [Print Jobs During Copy Operation]

[Prohibit]

The settings are not opened up to users.

[USB Connection Permission setting]

Select whether to collectively restrict functions using the USB Port, or configure a setting for each function.

If [Detail Setting] is selected, specify whether to permit the use for each function. For details, refer to the settings of [Detail Setting] shown below.

[Detail Setting] is specified by default.

[Authentication Device]

Select whether to permit a connection with the authentication unit.

[Allow] is specified by default.

[External Keyboard]

Select whether to permit a connection with an external keyboard.

[Allow] is specified by default.

[External Memory (User)]

Specify whether to allow the use of USB memory for functions to be used by the user.

Select whether to collectively restrict the following functions or configure a setting for each function. [Individual Settings] is specified by default.

• [Save Document]: Select whether to enable to save files on USB memory. [Restrict] is specified by default.

• [Print Document]: Select whether to enable to print files from USB memory. [Allow] is specified by default.

• [External Memory Document Scan]: Select whether to enable to save files scanned from USB memory into a User Box. [Restrict] is specified by default.

[External Memory (Administrator)]

Specify whether to allow the use of USB memory for functions to be used by the administrator.

Select whether to collectively restrict the following functions or configure a setting for each function. [Individual Settings] is specified by default.

• [Write the Config. from USB]: Select whether to permit a change on the settings of this machine by loading the configuration file saved in USB memory. [Allow] is specified by default.

[External Memory (Service)]

Used to specify whether to allow use of a USB memory by the service representative.

Select whether to collectively restrict the following functions or configure a setting for each function. [Individual Settings] is specified by default.

• [Storage data backup]: Select whether to permit the backup or restoration of the storage on this machine. [Restrict] is specified by default.

• [FW Update]: Select whether to allow firmware updating using USB memory. This option is available when [Administrator Settings] - [Security Settings] - [FW Update (USB) Perm. Sett.] is set to [USB Conn. Permission Setting Preference]. [Allow] is specified by default.

[PC Connection]

Specify whether to enable to print files from a USB-connected computer.

Select whether to collectively restrict the following functions or configure a setting for each function. [Individual Settings] is specified by default.

• [Print PC]: Select whether to enable to print files from a USB-connected computer. [Allow] is specified by default.

[Enable]/[Disable]

Select whether to enable Password Rules. Before enabling Password Rules, change the current password to the one that complies with the password rules.

[Disable] is specified by default.

Once Password Rules is enabled, the following rules are applied to any password that is configured on this machine.

• The minimum number of characters set in [Set Minimum Password Length] (default: 12)

• Passwords are case sensitive.

• A password consisting of a string of identical characters cannot be used.

• The previous password cannot be used.

The password rules are applied to:

• Administrator Password

• User Password

• Account Password

• User Box Password

• User Box Administrator Password

• Secure Print Document Password

• WebDAV Server Password

• SNMP Password

• Remote panel server password

• Encryption Passphrase

[Set Minimum Password Length]

If you enable Password Rules, change the minimum number of characters for a password, as required.

[Prohibit Functions When Auth. Error]

Select the severity of penalties applied if an incorrect password is entered during the authentication process.

• [Mode 1]: If authentication fails, the authentication operation (entry of password) is prohibited for five seconds.

• [Mode 2]: If authentication fails, the authentication operation (entry of password) is prohibited for five seconds. The number of times, authentication fails is also counted and if the failure count reaches a predetermined value, the authentication operation is prohibited and the machine is set into an access lock state.

[Mode 1] is specified by default.

[Release]

Select an item to be released from Access Lock during authentication failure.

[Release Time Settings]

If necessary, change the time that elapses before an access lock state in the Administrator Setting mode is canceled.

If a predetermined time has elapsed after the machine was restarted, an access lock state is canceled.

[5] min. is specified by default.

[Mode 1]

Displays all files when the document ID and password specified in the printer driver are entered. Select a desired file and print it.

[Mode 2]

Displays all files when the document ID specified in the printer driver are entered. To print, select your desired file, then enter the appropriate password for each file.

[Allow All]

Allows the direct input of destinations.

[Individual Allowance]

Select whether to allow direct input for each function.

[Restrict]

Prohibits the direct input of destinations. Hides [Direct Input] in the main screen in fax/scan mode.

[Job History]

Specify whether to hide personal information, such as destination and file name, in [Job History] in the [Job List] screen.

The default is [No] (without user authentication/account track) or [Yes] (with user authentication/account track).

[Display Settings]

When you have selected [Yes], select items you want to hide.

• [Mode 1]: Destination, file name, and user box name

• [Mode 2]: Destination, file name, and user box name, and user name

[Public User]/[User Authentication]/[Department]

Select how to display items you specified in [Display Settings] per Public User, User Authentication, and Authentication Track.

• [Mode 1]: Hide all display items.

• [Mode 2]: Hide only display items other than for login user/login account.

• [Mode 3]: Hide only display items other than for a public user, login user/public user, and login account.

• [Mode 4]: Show all display items.

[Current Job]

Specify whether to hide personal information, such as destination and file name, in [Active] in the [Job List] screen.

The default is [No] (without user authentication/account track) or [Yes] (with user authentication/account track).

[Display Settings]

When you have selected [Yes], select items you want to hide.

• [Mode 1]: Destination, file name, and user box name

• [Mode 2]: Destination, file name, and user box name, and user name

[Public User]/[User Authentication]/[Department]

Select how to display items you specified in [Display Settings] per Public User, User Authentication, and Authentication Track.

• [Mode 1]: Hide all display items.

• [Mode 2]: Hide only display items other than for login user/login account.

• [Mode 3]: Hide only display items other than for a public user, login user/public user, and login account.

• [Mode 4]: Show all display items.

[User Authentication/Account Track] - [General Settings] - [User Authentication]

Set to [Authenticate].

(When external server authentication is used, only Active Directory is available as the server type.)

[Security Settings] - [Administrator Password]

Set a password complying with password rules.

[Security Settings] - [Storage Management Settings] - [HDD Encryption Setting]

Enable the HDD Encryption.

In Web Connection, register the certificate.

For details, refer to Here.

Service settings

Service settings must be configured by your service representative.

For details, contact your service representative.

[System Settings] - [Restrict User Access] - [Restrict Access to Job Settings] - [Registering and Changing Addresses]^*

Set to [Restrict].

[User Authentication/Account Track] - [General Settings] - [Public User Access]^*

Set to [Restrict].

[User Authentication/Account Track] - [User Authentication Settings] - [Administrative Settings] - [User Name List]^*

Set to [OFF].

[User Authentication/Account Track] - [Print without Authentication]^*

Set to [Restrict].

[User Authentication/Account Track] - [User/Account Common Setting] - [Counter Remote Control]

Set to [Restrict].

[User Authentication/Account Track] - [URL Home Settings]

Set to [Disable].

[User Authentication/Account Track] - [Simple Auth. setting] - [Authentication Setting]^*

Set to [Restrict].

[Network Settings] - [FTP Settings] - [FTP Server Settings]^*

Set to [OFF].

[Network Settings] - [E-Mail Settings] - [E-Mail TX (SMTP)] - [Server Capacity Reduction Send Method]

When [Stop URL when max. limit is exceeded] or [Always Send via URL] is selected, this option is set to [OFF].

[Network Settings] - [E-Mail Settings] - [S/MIME Communication Settings]^*

• [Automatically Obtain Certificates] is set to [No].

• [3DES] is set if [E-Mail Text Encryption Method] has been set to one of [RC2-40], [RC2-64], [RC2-128], and [DES].

[Network Settings] - [SNMP Settings] - [SNMP v1/v2c Settings] - [Write Setting]^*

Set to [Invalid].

[Network Settings] - [SNMP Settings] - [SNMP v3 Settings]^*

[Security Level] for read and write allowed users is set to [auth-password/priv-password].

The Security Level can be changed to [auth-password].

[Network Settings] - [TCP Socket Settings] - [TCP Socket] - [Use SSL/TLS]

Set to [ON].

[Network Settings] - [WebDAV Settings] - [WebDAV Server Settings] - [SSL Setting]

Set to [SSL Only].

[Network Settings] - [Web Browser Setting]^*

Set to [OFF].

[Network Settings]-[Remote Panel Settings]^*

• [Client Settings]: Set to [OFF].

• [Server Setting]: Set to [OFF].

[Network Settings] - [E-Mail Settings] - [E-mail RX Print]^*

Set to [OFF].

[Network Settings] - [Machine Update Settings] - [Machine Auto Update setting]^*

This function is not available.

[Network Settings] - [IWS Settings]^*

Set to [OFF].

[Fax Settings] - [Report Settings] - [Tx Result Report Print Setting] - [Report File Attachment]^*

Set to [Without Attachment].

[System Connection] - [OpenAPI Settings] - [SSL/Port Settings] - [SSL Setting]

Set to [SSL Only].

[System Connection] - [Mobile Connection Settings] - [Simple Connection Setting]^*

• [QR Code Display Setting]: Set to [OFF].

• [Enable NFC]: Set to [OFF].

• [Enable Bluetooth LE]: Set to [OFF].

[Security Settings] - [Administrator Password Change Permission Setting]

Set to [Restrict].

[Security Settings] - [User Box Administrator Setting]^*

Set to [Restrict].

[Security Settings] - [USB Connection Permission setting]

Set to [Restrict].

[Security Settings] - [Security Details] - [Password Rules]^*

Set to [Enable].

If [Enable] cannot be selected for the Password Rules, you cannot enable the Enhanced Security Mode.

[Security Settings] - [Security Details] - [Prohibited Functions When Authentication Error]^*

• [Prohibit Functions When Auth. Error] is set to [Mode 2] and [No. of Tries] is set to [3]. No. of tries can be changed in the range between [1] and [3].

• [Release Time Settings]: Limited to [5] minutes. This value cannot be less than five minutes.

[Security Settings] - [Security Details] - [Confidential Document Access Method]

Set to [Mode 2].

[Security Settings] - [Security Details] - [Print Data Capture]

Set to [Restrict].

[Security Settings] - [Security Details] - [Hide Personal Information (MIB)]

Set to [ON].

[Security Settings] - [Security Details] - [Initialize]^*

If you select [Network Settings] and start it, the Enhanced Security Mode is canceled.

[Remote Access Setting] - [Import/Export User Data]

Set to [Restrict].

[Maintenance] - [Import/Export] in Web Connection

The password must be configured.

[Security] - [PKI Settings] - [Device Certificate Setting] in Web Connection

[Requesting Certificate] is hidden.

[Security] - [PKI Settings] - [SSL Setting] in Web Connection^*

• [Mode using SSL/TLS]: Set to [Admin. Mode and User Mode].

• [Encryption Strength]: If it has been set to [AES-256, 3DES-168, RC4-128, DES-56, RC4-40] or [AES-256, 3DES-168, RC4-128], it is changed to [AES-256, 3DES-168].

[Security] - [PKI Settings] - [Protocol Setting] in Web Connection

[Protocol 1]: [SSL], [Protocol 2]: The certificate is registered in the [http Server].

Remote Diagnosis System

Some functions may be disabled. For details, contact your service representative.

Preview Secure Document User Box

Only the list is displayed before the password authentication is performed.

[Security Settings] - [Maintenance Mode Permission]

Set to [Restrict].

[Yes]/[No]

Specify whether to automatically delete data stored on the hard disk or in the memory by overwriting.

[No] is specified by default.

[Overwrite Method]

Select the method for deleting data stored on the hard disk or memory by overwriting.

• [Mode 1]: Overwrites with 0x00.

• [Mode 2]: Overwrites with 0x00 - Overwrites with 0xff - Overwrites with letter "a" (0x61) - Verifies

[Mode 1] is specified by default.

[Encryption Priority]/[Overwrite Priority]

When setting [Overwrite HDD Data] with [HDD Encryption Setting] in combination, select the preferred option for deleting data stored on the hard disk.

• [Encryption Priority]: Overwrites data using a method different from [Mode 1] and [Mode 2] of [Overwrite Method]. To set [Overwrite HDD Data], select [Encryption Priority].

• [Overwrite Priority]: Overwrites data using the method specified at [Overwrite Method].

When changing this setting, you need to formatting the hard disk after restarting this machine. Before you attempt to change the setting, be aware that data may be deleted.

[Encryption Priority] is specified by default.

[Server Backup]

Backs up setting data to the server.

For details, refer to Here.

[Restore from Server]

Restores setting data from the server.

For details, refer to Here.

[HDD Backup]

Backs up setting data to the hard disk.

For details, refer to Here.