T00

Could not detect the fax signal from the recipient.

• Check to see if the destination is correct.
  Check that the recipient telephone number is for fax.

• Check that the recipient can receive faxes.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T01

Could not send a mixed original.

It is not possible to send a mixed original to the recipient. Confirm the specifications of the original that can be mixed, and send the original again (Scanning originals of different sizes ([Mixed Original])).

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T02

Could not detect the fax signal from the recipient.

If a communication error recurs, try the manual sending (Sending after Checking the State on the Recipient Side (Manual Transmission)).

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T03

An invalid communication protocol has been received.

Send a fax again.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T05

The recipient cannot receive faxes.

After a sufficient amount of time has elapsed, resend a fax. If this error is not resolved, contact the recipient to check the status.

If this error occurs repeatedly, contact your service representative.

T06

Could not establish a connection with the recipient.

Send a fax again.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T08

Could not establish a connection with the recipient.

Send a fax again.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T09

Could not establish a connection with the recipient.

Send a fax again.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T11

An error occurred in the receiver side.

Send a fax again.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T12

An error occurred in the receiver side.

Send a fax again.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T13

An error occurred in the receiver side.

Send a fax again.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T18

The recipient cannot receive faxes.

After a sufficient amount of time has elapsed, resend a fax. If this error is not resolved, contact the recipient to check the status.

If this error occurs repeatedly, contact your service representative.

T28

An error occurred in the receiver side.

Send a fax again.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T32

Could not establish a connection with the recipient.

Send a fax again.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T35

Could not establish a connection with the recipient.

Send a fax again.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T36

An error occurred in the receiver side.

Send a fax again.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T38

An invalid communication protocol has been received.

There may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T40

An error was detected on this machine.

Send a fax again.

If this error occurs repeatedly, contact your service representative.

T42

An image data reception failure occurred on the receiver side.

Set ECM to ON (Sending a Fax after Canceling ECM Mode ([ECM])).

• For registered address: [Address Book]

• For direct input: [Fax]

If this error occurs repeatedly, contact your service representative.

T43

A communication with the recipient was interrupted.

There may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T44

An error was detected on this machine.

Turn the main power OFF and then ON, and send a fax again.

T48

A communication was disconnected because the numbers do not match due to the Check Dest. & Send function.

• Check to see if the destination is correct.

• Check that the fax number registered with the recipient is correct.

• Set Check Dest. and Send to OFF; you may be able to send a fax (Checking the Destination Fax Number before Sending a Fax ([Check Dest. and Send])).

T50

A problem occurred during a communication with the remote diagnosis system.

Contact your service representative.

T51

An error was detected on this machine.

Turn the main power OFF and then ON, and send a fax again.

T52

An error was detected on this machine.

Turn the main power OFF and then ON, and send a fax again.

T58

The Polling TX original is not registered in the recipient.

Ask the other party to load the original.

T60

The Polling TX original is not registered.

Register the document that is sent to the recipient by polling (Registering a File for Polling ([Polling TX])).

T61

The Bulletin Polling TX original is not registered.

Check that the Bulletin Polling TX original is registered (Registering a File for Polling on the Bulletin Board ([Polling TX])).

T62

The Bulletin Polling TX has failed.

The recipient does not specify the correct bulletin board box number. Inform the recipient of the correct bulletin board number.

T68

The recipient does not have the optional polling function.

Check that the recipient has the appropriate function.

T73

An error occurred during V34 communication.

Set V34 to OFF to send a fax again (Sending a Fax after Canceling the Super G3 Mode ([V34])).

• For registered address: [Address Book]

• For direct input: [Fax]

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T74

An error occurred during V34 communication.

Set V34 to OFF to send a fax again (Sending a Fax after Canceling the Super G3 Mode ([V34])).

• For registered address: [Address Book]

• For direct input: [Fax]

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T75

An error occurred during V34 communication.

Set V34 to OFF to send a fax again (Sending a Fax after Canceling the Super G3 Mode ([V34])).

• For registered address: [Address Book]

• For direct input: [Fax]

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T76

An error occurred during V34 communication.

Set V34 to OFF to send a fax again (Sending a Fax after Canceling the Super G3 Mode ([V34])).

• For registered address: [Address Book]

• For direct input: [Fax]

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T77

An error occurred during V34 communication.

Set V34 to OFF to send a fax again (Sending a Fax after Canceling the Super G3 Mode ([V34])).

• For registered address: [Address Book]

• For direct input: [Fax]

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

T78

An error was detected on this machine.

Turn the main power OFF and then ON, and send a fax again.

T79

An error was detected on this machine.

Turn the main power OFF and then ON, and send a fax again.

T80

The machine may not be connected to the telephone line, or may be connected to the incorrect line.

Check that the machine is connected to the correct telephone line. Check that the machine is connected to the LINE terminal (Connection of Modular Cable).

T81

Could not recognize the dial tone.

• Try manual sending (Sending after Checking the State on the Recipient Side (Manual Transmission)).

• Check that the machine is connected to the correct telephone line.

• If you are using a PBX (private branch exchange), check the status of the PBX (Checking the PBX status before sending).

T82

The recipient did not respond.

• Check to see if the destination is correct.

• Check that the recipient telephone number is for fax.

• Check that the recipient can receive faxes.

T83

The recipient is on the phone or the address is incorrect.

• The recipient may be busy, so send a fax again after a while.

• Check whether the recipient telephone number is correct.

• Try the manual sending (Sending after Checking the State on the Recipient Side (Manual Transmission)).

T84

The address is entered incorrectly or contains a number prohibited by the administrator.

• In the address specification screen, enter only the recipient's telephone number following the outside line key.

• Check the [PBX Connection Setting] ([PBX Connection Setting]) or [Register address input prohibition rule.] ([Register address input prohibition rule.]).

T85

An instantaneous interruption was detected.

A contact failure may occur on a telephone line. Check to see if the line is disconnected.

T86

Could not correctly recognize the dial tone.

Try manual sending (Sending after Checking the State on the Recipient Side (Manual Transmission)).

If this error persists even after manual sending, the PBX (private branch exchange) or TA may be malfunctioning (Checking TA before sending).

T89

The balance is insufficient.

Check the amount or frequency displayed near the coin slot or card slot of the billing management device.

T95

An instantaneous interruption was detected.

A contact failure may occur on a telephone line. Check to see if the line is disconnected.

R00

Could not detect the fax signal from the sender.

The incoming call may be a wrong call.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

R01

Could not receive a mixed original.

Ask the sender not to send a mixed original or an original of a different resolution.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

R02

Could not establish a connection with the sender.

There may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

R03

An invalid communication protocol has been received.

If this error occurs repeatedly, contact your service representative.

R04

An invalid communication protocol has been received.

If this error occurs repeatedly, contact your service representative.

R06

An image data reception failure was detected.

There may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R07

A receiving error was detected.

If a fax is not resent, ask the sender to resend the fax.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R08

A communication with the sender was interrupted.

If a fax is not resent, ask the sender to resend the fax.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R09

A communication with the sender was interrupted.

If a fax is not resent, ask the sender to resend the fax.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R10

A communication with the sender was interrupted.

If a fax is not resent, ask the sender to resend the fax.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R11

A communication with the sender was interrupted.

If a fax is not resent, ask the sender to resend the fax.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R12

A communication with the sender was interrupted.

If a fax is not resent, ask the sender to resend the fax.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R18

Could not receive a fax because there is not enough free space in the box.

The erroneous User Box is displayed with a warning message. Delete unnecessary documents in the box (Delete a file).

R21

Could not receive a fax with the Closed Network RX function ([Closed Network RX]) because the password was not correct.

Set the Closed Network RX function to OFF in Administrator Settings, or ask the sender to set the correct password and resend a fax.

R22

The Closed Network RX function ([Closed Network RX]) is set, but the password was not notified.

Inform the sender of the Closed Network RX password, and ask them to specify the password. Ask the sender to resend a fax.

R24

A receiving error occurred.

There may be a problem with the line quality. If this error occurs repeatedly, contact the sender to check the status.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R25

A receiving error was detected.

If a fax is not resent, ask the sender to resend the fax.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact the sender to check the status.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R26

A receiving error was detected.

If a fax is not resent, ask the sender to resend the fax.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact the sender to check the status.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R27

A receiving error was detected.

If a fax is not resent, ask the sender to resend the fax.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact the sender to check the status.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R28

An invalid communication protocol has been received.

If a fax is not resent, ask the sender to resend the fax.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact the sender to check the status.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R29

A communication with the sender was interrupted.

If a fax is not resent, ask the sender to resend the fax.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R33

An invalid communication protocol has been received.

There may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

R34

An invalid communication protocol has been received.

Ask the sender to set password information to SID, not PWD.

If this error occurs repeatedly, contact your service representative.

R37

An error occurred during V34 communication.

V34 communication may not be possible because there is a problem with the line quality. If a fax is not resent, ask the sender machine side to set V34 to OFF and resend a fax.

If this error occurs repeatedly, contact the sender to check the status.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R38

An error occurred during V34 communication.

V34 communication may not be possible because there is a problem with the line quality. If a fax is not resent, ask the sender machine side to set V34 to OFF and resend a fax.

If this error occurs repeatedly, contact the sender to check the status.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R40

An error was detected on this machine.

Turn the main power OFF and then ON, wait until a fax is resent from the sender machine side.

If a fax is not resent, ask the sender to resend the fax.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R45

A communication with the sender was interrupted.

If a fax is not resent, ask the sender to resend the fax.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact the sender to check the status.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R49

A communication with the sender was interrupted.

If a fax is not resent, ask the sender to resend the fax.

If this error is not resolved, there may be a problem with the line quality. If this error occurs repeatedly, contact the sender to check the status.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R50

An image data reception failure was detected.

There may be a problem with the line quality. If this error occurs repeatedly, contact the sender to check the status.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R51

An error was detected on this machine.

Turn the main power OFF and then ON, wait until a fax is resent from the sender machine side. If a fax is not resent, ask the sender to resend the fax.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R52

An error was detected on this machine.

Turn the main power OFF and then ON, wait until a fax is resent from the sender machine side. If a fax is not resent, ask the sender to resend the fax.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R60

An image data reception failure was detected.

There may be a problem with the line quality. If this error occurs repeatedly, contact the sender to check the status.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R63

A communication with the sender was interrupted.

There may be a problem with the line quality. If this error occurs repeatedly, contact the sender to check the status.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R67

An invalid communication protocol has been received.

Request the sender machine side not to set SUB of F-Code. If this error occurs repeatedly, contact your service representative.

R69

A communication with the sender was interrupted.

There may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R70

An error was detected on this machine.

If a fax is not resent, ask the sender to resend the fax.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R71

An image data reception failure was detected.

There may be a problem with the line quality. If this error occurs repeatedly, contact the sender to check the status.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R72

The received original is too long.

Ask the sender to resend the original with a length of less than 1 m (39-3/8 inches).

R73

An error was detected on this machine.

There may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R74

An image data reception failure was detected.

There may be a problem with the line quality. If this error occurs repeatedly, contact your service representative.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R75

An error occurred during V34 communication.

V34 communication may not be possible because there is a problem with the line quality. If a fax is not resent, ask the sender machine side to set V34 to OFF and resend a fax.

If this error occurs repeatedly, contact the sender to check the status.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R76

An error occurred during V34 communication.

V34 communication may not be possible because there is a problem with the line quality. If a fax is not resent, ask the sender machine side to set V34 to OFF and resend a fax.

If this error occurs repeatedly, contact the sender to check the status.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R77

An error was detected on this machine.

If this error occurs repeatedly, contact your service representative.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R78

An error was detected on this machine.

If this error occurs repeatedly, contact your service representative.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R79

An error was detected on this machine.

If this error occurs repeatedly, contact your service representative.

* Duplicate pages may be output when the resent original is received. Check for duplicate pages.

R80

A problem occurred during a communication with the remote diagnosis system.

Contact your service representative.

R81

A problem occurred during a communication with the remote diagnosis system.

Contact your service representative.

R82

A problem occurred during a communication with the remote diagnosis system.

Contact your service representative.

R83

A problem occurred during a communication with the remote diagnosis system.

Contact your service representative.

R84

A problem occurred during a communication with the remote diagnosis system.

Contact your service representative.

R94

An error was detected during Relay RX.

Check that the relay destination (Group) of the Relay User Box is registered properly (Registering a Relay User Box). Otherwise, inform the sender of the correct password, and ask them to resend a fax.

R96

An error was detected during Relay RX.

Check that the Relay RX (Registering a Relay User Box) User Box is correctly registered. Otherwise, check whether the Relay RX function is turned off.

Inform the sender machine side of the correct User Box number.

R99

Could not respond to an incoming call that was received.

Wait until a fax is resent from the sender machine side. If a fax is not resent, ask the sender to resend the fax.