[Height]

Sets the height of the finishing size.

Set the value so that the width of the cut paper is 120 mm / 4.72" or more.

Unit: 0.1 mm / 0.004"

[Width]

Sets the width of the finishing size.

Set the value so that the length of the cut paper is 133 mm / 5.24" or more.

Unit: 0.1 mm / 0.004"

[Rear Edge]

Sets the cut position at the rear edge using the value from the upper edge of paper.

Set the value in the range of 0 mm / 0" or 8.0 mm to 30 mm / 0.31" to 1.18" (paper weight 64 g/m² / 17 lb Bond or less: 10 mm to 30 mm / 0.39" to 1.18") so that the difference between [Rear Edge] and [Front Edge] is within 10 mm / 0.39".

Only either side of [Rear Edge] and [Front Edge] cannot be set to 0 mm / 0".

Unit: 0.1 mm / 0.004"

[Front Edge]

The front edge is automatically calculated from the paper size (lengthwise), finishing size ([Height]), and [Rear Edge].

[Front Edge] = Paper size (lengthwise) - Finishing size ([Height]) - [Rear Edge]

[Leading Edge]

Sets the cut position at the leading edge using the value from the lead edge of paper.

WY1: Set the value in the range of 0 mm / 0" or 10 mm to 100 mm / 0.39" to 3.94" so that the slitting amount of [Trailing Edge] is in the range of 0 mm / 0" or 10 mm to 13 mm / 0.39" to 0.51".

WY2 or later: Set the value in the range of 0 mm / 0" or 8.0 mm to 100 mm / 0.31" to 3.94" so that the slitting amount of [Trailing Edge] is in the range of 0 mm / 0" or 8.0 mm to 18 mm / 0.31" to 0.71".

Unit: 0.1 mm / 0.004"

[Trailing Edge]

The trailing edge is automatically calculated from the paper size (widthwise), finishing size ([Width]), and [Leading Edge].

[Trailing Edge] = Paper size (widthwise) - Finishing size ([Width]) - [Leading Edge]

[FD Perforation (Rear Edge)] / [FD Perforation (Front Edge)]

Up to 2 perforation positions in the paper feed direction can be set in the rear and front sides.

WY1 (Perforation Unit PE-101): Set so that the perforation position is 30 mm / 1.18" or more from [Rear Edge] or [Front Edge], and that the distance between the perforation positions in the rear and front sides is 100 mm / 3.94" or more.

WY2 (Perforation Unit PE-101): Set so that the perforation position is 10 mm / 0.39" or more from [Rear Edge] or [Front Edge], and that the distance between the perforation positions in the rear and front sides is 100 mm / 3.94" or more.

Unit: 0.1 mm / 0.004"

[Size] (Feed direction)

Set the perforation length of the paper feed direction. The rear side and the front side have the same value.

WY1 (Perforation Unit PE-101): Set the value to 30 mm / 1.18" or more.

WY2 (Perforation Unit PE-101): Set the value to 5.0 mm / 0.20" or more.

Unit: 0.1 mm / 0.004"

[CD Perforation1] to [CD Perforation10]

Set the perforation position in the crosswise direction. You can set up to 10 perforation positions in each of the back and front sides.

WY1 (Perforation Unit PE-102): Set so that the perforation position is 30 mm / 1.18" or more from [Leading Edge], and that the distance between the perforation positions is 30 mm / 1.18" or more.

WY2 (Perforation Unit PE-102): Set so that the perforation position is 5 mm / 0.20" or more from [Leading Edge], and that the distance between the perforation positions is 9.0 mm / 0.35".

Unit: 0.1 mm / 0.004"

[Size (Rear Edge)] / [Size (Front Edge)] (Crosswise direction)

Set the perforation length of the crosswise direction in the rear and front sides respectively.

WY1 (Perforation Unit PE-102): Set the value to 30 mm / 1.18" or more.

WY2 (Perforation Unit PE-102): Set the value to 10 mm / 0.39" or more.

Unit: 0.1 mm / 0.004"

[Disabled]

Clear this check box to set a perforation position.

[Complete]

Creates a trimmer profile with the specified value.

[Cancel]

Cancels the setting, and returns to the previous screen.

[PDF Download]

You can download the trimming image with the dimensions displayed on the profile creation screen as a PDF file. This is displayed when accessed from Web Connection or Web Utilities.