Switching the corresponding switch numbers resolves phenomena or requirements described in the following list.
All the software memory switches are set to [Off] by default. Changing from [Off] to [On] may resolve a problem that occurred.
Switch No. | Problem/Requirement | Solution reached when turned On |
---|---|---|
1 | The paper size should be distinguished using the CropBox value (trimming size) in order to direct-print a PDF file. In general use, the MediaBox (media size) value is used as the standard. | The paper size is distinguished using the CropBox value (trimming size) of a PDF file. |
2 | When multiple print jobs are collected to a single file and printed using the LPR command, an error occurs, causing an output failure. | After receiving all data (file), execute print jobs regardless of the controller's spool setting. In this case, the printing speed may slow down. The maximum file size that can be received for each file is within 2 GB. If the maximum file size exceeds 2 GB, no effect of setting change will be ensured. After the setting is changed, turn Sub power switch off, and on again to confirm the setting. |
4 | When multiple PostScript data items are collectively output to a single file via the network, multiple data items are collectively output to a single job. | When [Ctrl] + [D] is detected, it is judged to be a job delimiter, enabling you to output them as multiple jobs. |
5 | When multiple PostScript data items are collectively output to a single file via USB, a single job is divided and output. Also, error pages may be output. | When [Ctrl] + [D] is detected, a single job can be output as a single job without being judged to be a job delimiter. |
7 | When multiple jobs are collectively output to a single file, whether or not to delimit them should be selectable by judging the range from the PJL JOBNAME command to the PJL EOJ NAME command to be a job delimiter. | Setting value [Off]: Outputs multiple jobs as a single file without delimiting them. [On]: Outputs multiple jobs as they are by delimiting them. |
11 | The paper tray of this system should always be specified automatically. | The paper tray is always specified automatically regardless of the paper tray specified in the printer driver. |
12 | The file name specified in the LPR command, not the job name specified in the printer driver, should be displayed as the job name. | The file name specified in the LPR command is displayed as the job name. |
13 | When an attempt is made to install fonts using Font Management Utility, a timeout error occurs. | A timeout error is avoided. However, the RAM font type is displayed as [HDD] in the font list of Font Management Utility. |
15 | In Mac OS X or later, when multiple body copies are specified with cover insertion, only 1 copy of the body is output. | The specified number of copies of the body are output. However, if a job including font data or EPS data is output, error pages may be output. |
16 | When the LPR command (-J) is used in Mac OS, a banner page should be printed out. | A banner page is printed out. However, even if the LPR port is used from the printer driver when printing, a banner page is printed out. |
18 | The paper type specified in [MediaType] of a PS command should be registered as the paper name. | If the specified paper name is not registered on the [Register/Delete Paper Setting] screen after it is sent to the engine, it is registered automatically. Setting value [Off]: Not registered. [On]: Registered. * To confirm the [Register/Delete Paper Setting] screen, select Utility/Counter - [User Setting] - [System Setting] - [Paper Tray Setting] - [Paper Setting] - [Paper Profile Setting]. |
25 | When a job with the mixed original specified, which includes an original of 8.5 e 11 v size, is output by direct printing, it is recognized as the 9 e 11 v size. | Such a job is printed with 8.5 e 11 v size. |
26 | PostScript error, [Limitcheck], occurs. | Reduce the occurrence of PostScript error, [Limitcheck]. * When an attempt is made to print a large number of jobs or a large capacity job, [Limitcheck] may occur.
|
27 | When specific PS data is output, an error occurs, so PostScript (Level1) commands should be supported. | Setting value [Off]: Does not support PostScript (Level1) commands. [On]: Support PostScript (Level1) commands. Selecting [On] allows you to use the following Level1 commands. Lettertray, legaltray, ledgertray, a3tray, a4tray, b5tray, 11x17tray, #copies
|
28 | Cannot edit the job stored in the HDD using the PPD Driver in AccurioPro Print Manager. | Allows editing. However, the printing speed may slow down. Editing is also possible even if the job is set to Save (or Save & Print) with No. 48/49. |
31 | When using PDF direct printing, content related to transparency may not be output. | You may be able to resolve this issue depending on whether or not device colors are used. Setting value [Off]: Does not use device colors. [On]: Uses device colors. |
32 | When a PDF file is converted to a PostScript one, complicated transparent objects cannot be correctly converted in certain cases. | Switch the conversion method to address this problem. Setting value [Off]: Converts for each object. [On]: Converts the entire page. |
33 | When an attempt is made to output PCL data in duplex mode, blank pages on back sides are discarded. | Also prints back sides that are blank pages. However, there is no charge for blank pages. |
34 | When an attempt is made to download a large number of PS fonts, it may take a long time to print the PS font list. | Only display the font name without outputting sample characters of the downloaded fonts to the font list; the PS font list printing speed will increase. |
36 | When an attempt is made to output PCL XL/TIFF data of the mixed-size original (A4 v/w), the bind position of a landscape original is changed compared with the original output from the PS driver. | The original is printed at the same bind position as when it is output from the PS driver. |
38 | When an original is printed via Linux, it is output in banner format, so banner output should be disabled. | Disable the -C option (banner creation) of the LPR command. Setting value [Off]: Enables the -C option. [On]: Disables the -C option. |
40 | The file stored in a hot folder of AccurioPro Hot Folder should be printed on paper of a size that is closest to the size of the original in the paper tray. | When the output paper size is [Auto]; the output tray is [Auto]; and this setting is [On], the file is printed on paper of a size that is closest to the size of the original in the paper tray. However, if there is no output paper, the file is printed on paper of a size selected with a regular APS (automatic paper). |
43 | If MIB (kmNetHttpdEnable) is changed from "disable" to "enable", [Web Connection Setting] in [Administrator Setting] - [Controller] - [Simple Security Setting] should also be changed synchronously. | Setting value [Off]: Does not synchronize MIB with Web Connection. [On]: Synchronizes MIB with Web Connection. |
45/46 | When an attempt is made to print a job without using the printer driver or AccurioPro Hot Folder, it should be possible to specify the color mode. | The color mode can be specified. Setting value
|
47 | When a specific PDF original (with overprint attribute) is held or printed, it may take a long time, or no data may be output. | This problem may be resolved by canceling the overprint setting that converts data from PDF to PS. Setting value [Off]: Uses the overprint setting. [On]: Does not use the overprint setting. General precaution When the overprint setting is not used, the output result may be different. |
48/49 | Print, Store, or Print/Store should be forcibly applied regardless of the specification of the printer driver. | Forcibly apply the following settings. Setting value
|
Switch No. | Problem/Requirement | Solution reached when turned On |
---|---|---|
51 | When a job involving paper that is larger than the maximum paper size supported by this system is output using AccurioPro Hot Folder, it is output as an error page without being printed, however, the center part should be printed out at the full size. | [Off]: Outputs an error page (for PS or PDF). Reduced for output (for TIFF). [On]: Outputs the center part at the full size.
Restrictions For PS and PDF When [Off] is selected, if the original size exceeds the maximum paper size supported by this system, an error page is output. When [On] is selected, if the original size exceeds 1,600 mm e 2,100 mm / 62.99" e 82.68", an error page is output. For TIFF When [On] is selected, if the size exceeds 900 mm e 1,320 mm / 35.43" e 51.97", images may be printed out of alignment. |
55 | When data with crop marks is printed, the crop marks of monochrome pages should be printed in black only, not in mixed CMYK colors. | Setting value [Off]: Prints crop marks of monochrome pages in mixed CMYK colors. [On]: Prints crop marks of monochrome pages in black only. |
59 | When using the RAW protocol, if the "EOT0x04" code is received in use of the RAW protocol, EOT should be echoed back. | Setting value [Off]: Does not echo back EOT. [On]: Echoes back EOT. |
61 | Borderless printing should be available for a job created by the PCL5 command. | Borderless printing is available for a job created by the PCL5 command. Setting value [Off]: Does not use borderless printing. [On]: Uses borderless printing |
62/63 | The status notification email indicating completion of a print job should be sent without using the PS Plug-in Driver. | Sends a notification mail to the administrator's address with the following settings. Setting value 62/63 = [Off]/[Off]: Does not send a notification email. 62/63 = [Off]/[On]: Always sends a notification email to the administrator's address. 62/63 = [On]/[Off]: Sends a notification email to the administrator's address only when an error occurs. |
66 | In general use, the output of the settings configured in the printer driver or AccurioPro Hot Folder has priority over that of the settings configured in [Direct Print Setting] in [Controller]. The contents of [Direct Print Setting] should be output preferentially. | Setting value [Off]: Gives priority to the setting of the printer driver or AccurioPro Hot Folder. [On]: Gives priority to [Direct Print Setting]*. * [Direct Print Setting] can also be set in [Printer Settings] of Web Connection for the Image Controller. |
68 | JDF support by APPE should be enabled to support the direction connection with Adobe applications. | Setting value [Off]: Disables the JDF parameter support by APPE (converts JDF to an internal job ticket with the controller JDF module). [On]: Enables the JDF parameter support by APPE (analyzes JDF with APPE).
|
70 | The number of jobs that can be held in the Image Controller should be increased. | Setting value [Off]: 1,000 jobs (RIPed job: 500, UnRIPed job: 500) [On]: 3,000 jobs (RIPed job: 1,500, UnRIPed job: 1,500) Restrictions If 501 or more RIPed or UnRIPed jobs are held in [On], it is not possible to switch from [On] to [Off]. Important
|
71 | Whether to make the form of the PS Plug-in Driver transparent should be changed. | Setting value [Off]: Makes the form transparent regardless of objects. [On]: Does not make the form transparent regardless of objects. Restrictions If the custom screen is set, this option is not applied. |
74/75 | The method for handling an RGB value error in gray replacement should be changed. The RGB value may not be equal for a grayscale image in a Microsoft Office application. If an error is not allowed, gray replacement cannot be performed (a grayscale image is handled as a colored image). To resolve this problem, set the allowable range of an error that is assumed to be R = G = B. | You can set the allowable range of R = G = B. Setting value
|
77 | It should be possible to store a PPML file in AccurioPro Print Manager, and change the number of copies for each page. | Setting value [Off]: Does not allow the storage of a PPML file. [On]: Allows the storage of a PPML file. When set to [On] (about the stored PPML file):
|
78 | When the number of hold jobs in AccurioPro Print Manager reaches the upper limit of 500, jobs should be deleted from the oldest registration date. | Setting value [Off]: Deletes jobs from the oldest update time and date. [On]: Deletes jobs from the oldest registration date. Restrictions This option is only available for hold jobs. It is not available for HDD store jobs. |
79 | When images on the original over the standard size are shifted by the image shift function and output to standard size paper using AccurioPro Hot Folder (PDF only), processing should be performed so that no image missing occurs. | Perform image shift with RIP to prevent a print side missing from occurring. Setting value [Off]: Does not perform image shift with RIP. [On]: Performs image shift with RIP. Restrictions
|
80 | The image shift function (PDF only) of switch No. 79 should be applied to a PS job. | Perform image shift with RIP to prevent a print side missing from occurring. Setting value [Off]: Does not perform image shift with RIP. [On]: Performs image shift with RIP. Restrictions
|
81 | Normally, when an original with monochrome and color mixed is output from Apogee, the application cannot automatically distinguish between them, so this system processes with Auto Color. In that case, the printing speed drops slightly, so output processing should be performed without reducing the printing speed by using Full Color. | Setting value [Off]: Processes jobs output in CMYK from Apogee as Auto Color. [On]: Processes jobs output in CMYK from Apogee as Full Color. |
82 | When [Maintenance] tab - [Status Notification Setting] - "Replenish Paper Tray" is selected in Web Connection for the Image Controller, an email notification is issued when a regular tray is out of paper; however, it should be issued before the paper supply runs out. | Change a notification of "Replenish Paper Tray" in [Status Notification Setting]. Setting value [Off]: Issues a notification when the tray is out of paper. [On]: Issues a notification before the tray runs out of paper. |
84 | The [LPQ -P] commands used on Linux should be supported. | Setting [Off]: No response returns when the [LPQ -P] command is input. [On]: When the [LPQ -P] command is input, [Ready] or [Not Ready] returns depending on the device status. When [Ready] or [Not Ready] is returned, the specifications are as follows.
|
89 | The contents of setting information prints should be all printed in black characters. | Setting value [Off]: Does not print all in black characters. [On]: Prints all in black characters. |
91 | When Pure Black or Gray Replacement is used for a gradation object using APPE, the colors around the target color are also affected. Therefore, it should be possible to select whether to apply Pure Black or Gray Replacement for a gradation object or make adjustments so that the colors around the target color are not affected. | [Off]: Also applies Pure Black or Gray Replacement to a gradation object. However, the colors around the target color are also affected in addition to the colors targeted for Pure Black or Gray Replacement. [On]: Does not apply Pure Black or Gray Replacement to a gradation object. In this case, the colors around the target color are not affected. |
93 | When a special color included in print data is not registered in the controller, the data should be temporarily stored on the HDD without being printed, and placed in standby state as an error. | Temporarily store print data on the HDD, and place it in a standby state as an error. Setting value [Off]: Does not temporarily store print data on the HDD. [On]: Temporarily stores print data on the HDD. Restrictions
|
94 | When PPML data is printed on a mixed page, if a reuse object is used, a missing page will be created. Even if a reuse object is used, creation of a missing page should be avoided by adjusting the rotation position. | Setting value [Off]: Disables reuse object position adjustment. [On]: Enables reuse object position adjustment. |
95 | The automatic paper tray selection function should be used by converting [MediaPosition1(tray2)] and [MediaPosition2(tray3)] of the PS command for paper tray specification to [MediaColor(Other)] and [MediaColor(White)]. | Setting value [Off]: Does not perform command conversion. [On]: [MediaPosition1] is converted to [MediaColor(Other)], and [MediaPosition2] to [MediaColor(White)]. The specifications of the [MediaColor] command are as follows.
Tray: Automatic, Paper color: Others
Tray: Automatic, Paper color: White |
97 | Unnecessary tab paper should be discharged when a JDF-compatible application is used for printing. | Setting value [Off]: Not be discharged. [On]: Discharged. |
98 | The spine should not be made blank when [Cover Print 2 in 1] is selected for perfect binding. | Setting value |
99 | Switches whether to perform re-RIP when the paper type is changed. | Setting value [Off]: Performs re-RIP. [On]: Does not perform re-RIP. |
Switch No. | Problem/Requirement | Solution reached when turned On |
---|---|---|
104 | When an attempt is made to operate the AccurioPro Print Manager screen from the Touch panel, accesses from another computer should be restricted in order to speed up the screen display. | Setting value [Off]: Cannot connect to AccurioPro Print Manager on the Touch panel from another computer. [On]: Can connect to AccurioPro Print Manager on the Touch panel from another computer.
|
105 | It should be possible to enter the number of copies using the keypad on the Control panel in order to reduce the number of operation steps when printing on the AccurioPro Print Manager screen from Touch panel. | Setting value [Off]: The on-screen keypad is displayed. [On]: The on-screen keypad is not displayed. |
107 | The Hot Folder of this system should be able to output PCL 5e files. | Setting value [Off]: Does not support PCL 5e. [On]: Supports PCL 5e. If [On] is selected, the system outputs a large amount of pages on which binary data are printed when handling file formats that are not supported by Hot Folder of this system. |
108 | A large amount of pages on which binary data are printed should not be output when file formats that are not supported are output by a function other than Hot Folder (such as Direct Print). | Prevents printing of binary data by not supporting PCL 5e, since those formats are output based on PCL 5e. If [On] is selected, they will not be output but treated as errors. Setting value [Off]: Supports PCL 5e. [On]: Does not support PCL 5e. |
109 | When printing an A4-size original with 2 Repeat or 2 Repeat Reversal using the printer driver, the crop mark printing position is misaligned. | If the paper size exceeds the maximum printing size of this system, the printing position is misaligned. Setting value [Off]: Does not correct the position. [On]: Corrects the position. Restrictions This setting is only available for following:
|
110 | When a specific PS job* is direct-printed, the number of copies specified in PJL is not reflected, and only 1 copy is printed in certain cases. Therefore, the correct number of copies, specified in PJL, of such a job should be printed. * The specific PS job refers to a job for which the job settings such as Staple are configured in Custom Operator of PS. | The number of copies specified in PJL has priority. |
111 | Staple setting should be supported in the page unit specified for a PS file. | Setting value [Off]: Does not support the staple setting. [On]: Supports the staple setting. |
112 | The print position setting (front edge, center, and rear edge) of AccurioPro Hot Folder should also be available in addition to the setting of switch No. 40. | Setting value [Off]: Does not follow the print position setting. [On]: Follows the print position setting. Restrictions
|
115 | The CPSI maximum ImageBuffer size should be changed to prevent memory shortage occurring when performing RIP. | It may be possible to solve the problem by increasing the CPSI maximum ImageBuffer size. Setting value [Off]: Default (1MB) [On]: Increases (5MB)
|
116 | When a PDF file is imported using APPE, each image should be generated based on the printing area size. | Setting value [Off]: Based on the PDF original size. [On]: Based on the printing area size (same as CPSI). Restrictions
|
117 | If blank pages are inserted with [Page Edit] and [Fold & Staple] is set, the body pages are processed with Fold & Staple, but the blank pages are processed with Half-Fold. Mixing Fold & Staple and Half-Fold should be avoided by changing the staple settings for blank sheet insertion pages to the same settings as those used for the body pages. | Setting value [Off]: Does not set. [On]: Changes the staple settings for blank sheet insertion pages to the same settings as those used for the body pages. Restrictions
|
119 | When a certain PDF file is RIPed with APPE, an error occurs, and the file freezes. Also, subsequent jobs are not processed, causing problems. | When an error occurs, you may be able to solve the problem by restarting APPE before starting the next job. Setting value [Off]: Do not restart APPE. [On]: Restarts APPE. |
124 | The "Fit to Paper Size" function should be limited to Reduce Only in AccurioPro Hot Folder. | Setting value [Off]: Reduces or enlarges to suit the paper size. [On]: Reduces to suit the paper size (does not enlarge). Restrictions
|
125 | When "Fit to Paper Size" is selected in AccurioPro Hot Folder, the paper size should be switched to the printing area. | Setting value [Off]: Suits the paper size. [On]: Suits the printing area. Restrictions
|
127 | A transparent object of a Microsoft Office application should be output with high resolution. Setting at a high resolution may resolve the conspicuousness of dots that are caused depending on the transparency percentage when printing. | Setting value [Off]: Does not set to high resolution. [On]: Sets to high resolution. If [On] is selected, data is always spooled for PostScript printing regardless of the machine setting. Restrictions
|
128 | When printed with APPE, the text is thicker than when printed with CPSI. | It may be possible to solve the phenomenon by limiting the amount of toner when printing with APPE. Setting value [Off]: Does not set the toner amount limit. [On]: Sets the toner amount limit. |
129 | When printing a job without RIP with AccurioPro Print Manager, it is not possible to distinguish between printing or saving from the [Job Management] screen and printing by selecting a job and right-clicking - [Print...]. | Set whether to save [Range] to distinguish it. Setting value [Off]: Saves [Range]. [On]: Does not save [Range]. Restrictions This setting is only available when switch No.189 is set to [On]. |
130 | The number of copies and that of pages of a job should be printed on banner pages in PS Plug-in Driver. | Setting value [Off]: Does not print the number of copies and that of pages of a job on banner pages. [On]: Prints the number of copies and that of pages of a job. Restrictions
|
131 | In general use, banner pages in PS Plug-in Driver are output before a job, but they should be output after a job. | Setting value [Off]: Prints in the order of banner pages -> job. [On]: Prints in the order of job -> banner pages. |
132 | The two conflicting functions below can be set simultaneously for a PCL job.
By default, "Specify Text Margin" has priority in the PCL-compliant specifications, but "Horizontal Motion Index", the HP-compatible specification, should be set to be given priority. | Turn this switch [On] to change to the HP-compatible specifications. Setting value [Off]: Prioritizes "Specify Text Margin". (PCL-compliant specifications) [On]: Prioritizes "Horizontal Motion Index". (specifications compatible with the HP machine) |
135 | A notification email should be sent to the email address specified in "Status Notification Setting" under [Network Setting] - [NIC Settings] - [Detail Settings] at each of the times specified in "Print Start (Job Started)" and "Print End (Job finished)". | Setting value [Off]: Does not send a notification email. [On]: Sends a notification email. Restrictions A notification email can only be sent to "E-mail address 1". |
143 | All form files in the controller that can be created from PS Plug-in Driver should be allowed to be deleted all at once from tools used by the customer (the driver can only delete one at a time). | Setting value [Off]: Does not support. [On]: Does support. Deleting by using the default password, "password", will delete all form data. |
145 | If a PPML file is printed with an application such as "Pageintegrator Pro", some characters are missing or "PPML RIPError" occurs, causing a printing failure. | The problem may be resolved by disabling the function that deletes duplicate subset fonts. Setting value [Off]: Enable the delete function. [On]: Disable the delete function. |
146 | A font error is ignored in Adobe Acrobat, but it should be output as an error without being ignored n APPE. | Setting value [Off]: Ignores a font error. [On]: Does not ignore a font error. |
147 | When the number of sets is set to 1 or [Group] using Job Edit of AccurioPro Print Manager, the setting should be forcibly changed to [Sort]. | When the number of sets is set to 1, the setting is fixed to [Group]. |
149 | DLP (Device Link Profile) for each tab should be specified when composite printing is performed using APPE. | Setting value [Off]: Restricts the DLP specification for each tab when composite printing is performed using APPE. [On]: Enables the DLP specification for each tab even when composite printing is performed using APPE. |
150 | The color bar and color setting information should be printed on all pages when a poster is printed. | Setting value When banner page is set for poster printing [Off]: Prints the color bar and color setting information only on banner pages. [On]: Prints the color bar and color setting information on all pages. Restrictions
|
Switch No. | Problem/Requirement | Solution reached when turned On |
---|---|---|
151 | The page with the Duplex command specified should be printed on the front side. | Print the page with the Duplex command specified on the front side. Restrictions
|
152 | When direct printing is used, the setting information and color bar printing positions are different from those when PS Plug-in Driver is used. This phenomenon occurs when the original orientation (portrait or landscape) is changed.
| Setting value [Off]: Sets the setting information and color bar printing positions to the same positions as when PS Plug-in Driver is used. [On]: Matches the setting information and color bar printing positions with the original size regardless of the original orientation setting. |
153 | When setting output offset, I should apply the [Change Out Pos. + Partition Paper] operation from the first page of the job regardless of the job unit or copy unit. | Setting value [Off]: Sets the following operations to the default when making output offset.
[On]: Sets the following operations to the default when making output offset.
|
156 | Printing stops before the last copy of multiple jobs (2 to 10 sets) sent from the VPSX server is printed. | Extending the job end detection function may resolve a phenomenon that stops printing. Setting value [Off]: Does not extend the job end detection function. [On]: Extends the job end detection function. |
157 | The contents of Result is not output as the response result of the EOJ command, so it should be output. | Configure the setting to output the contents of Result. Example: Result = OK, etc. Setting value [Off]: Not output. [On]: Output. |
158 | A profile for converting CMYK data to grayscale is different between CPSI and APPE, and the CPSI profile is used ordinarily. The image quality of high-density photo data created in CMYK may be improved by using the APPE profile, so a profile equivalent to the APPE profile should be applicable. | Setting value [Off]: Uses the CPSI conversion profile. [On]: Uses the conversion profile equivalent to the APPE profile. Restrictions
|
159 | The gradation of the CMYK high-density parts is ordinarily reproduced in the APPE profile that converts CMYK data to grayscale, so areas of original data with a black density of 100% cannot be output with a black density of 100%. Therefore, such an area should be forcibly output with a black density of 100%. | An image object cannot be held with a black density of 100%, so configure the setting so that it can be held. Setting value [Off]: Does not maintain a black density of 100% when outputting in grayscale. [On]: Maintains a black density of 100% when outputting in grayscale. Restrictions
|
160 | The maximum number of registered CMYK-CMYK direct link profiles should be extended to 100 or more. | Setting value [Off]: Allows you to register up to 50 CMYK-CMYK direct link profiles. If 50 or more CMYK-CMYK direct link profiles are included in the database at start-up, leave only 50 profiles of which the registration date is earlier. Delete the remaining 50 profiles (however, the setting is configured so that the preset profiles and profiles specified by the color default cannot be deleted). [On]: Allows you to register up to 100 CMYK-CMYK direct link profiles. |
161 | When the number of registered CMYK-CMYK direct link profiles exceeds the maximum value, it should be possible to automatically delete the oldest profile and register a new profile. | Setting value [Off]: Disables a new registration when the number of registered CMYK-DLP direct link profiles reaches the maximum value. [On]: Deletes the table of which the creation date and time are oldest from the list and register a new CMYK-DLP profile when the number of registered CMYK-DLP profiles reaches the maximum value. |
162 | When [2-Color Printing] (used as monocolor) is set in PS Plug-in Driver, if the same special color specified in the driver is included in the original at the time of printing, the density may become thin. If the same special color is included in the original, it should be printed at the same density without being changed. | Setting value [Off]: Specifies the special color for which the plate (CMYK) is replaced for 2-color printing, and changes the special color on the original if that special color is included in the original. However, the density may become thin. [On]: Specifies the special color for which the plate (CMYK) is replaced for 2-color printing, and outputs with the same density without changing the special color on the original if that special color is included in the original. |
163 | When an attempt is made to print an APPE job in AccurioPro Hot Folder, a problem in which the top-bottom order is reversed occurs, but it does not occur in a CPSI job. An improvement should be made so that such a problem does not occur in a APPE job in the same way as a CPSI job. The following causes are assumed. CPSI: An image is created based on the actual orientation of the original. APPE: An image is created based on the [Original Orientation] setting of AccurioPro Hot Folder. | Setting to [On] forcibly ignores the [Original Orientation] setting of AccurioPro Hot Folder to suit the orientation of the first page of the original, and may allow you to resolve this problem. Setting value [Off]: Follows the [Original Orientation] setting of AccurioPro Hot Folder. [On]: Suits the first page of the original. * A mixed original is printed to match the orientation of the 1st page of the original regardless of the setting. Restrictions
|
164 | To send scanned data using Scan To E-mail after login when [Authentication Method] of [User Authentication] is set to [External Server], the address of this email should be set to the administrator address of this system. | Changes the sender address of the email sent using Scan To E-mail. Setting value [Off]: Disable (The address is specified to suit the environment (for example, the authentication user's address is specified).) [On]: Enable (The administrator address of this system is specified.) |
166 | If the following indirect object is included in the received PDF file, it should be detected and duplex-printed. Indirect object: DuplexFlipLongEdge (Print 2-Sided, Long Edge) DuplexFlipShortEdge (Print 2-Sided, Short Edge) | Specify so that an indirect object is detected and duplex-printed. Setting value [Off]: Not detected. [On]: Detected. Restrictions
|
167 | When data is printed using the PDF composite overprint function of APPE from AccurioPro Print Manager, parts that contain many objects with transparency attributes are processed, but it takes a long time. | Change the APPE rasterizing method for printing. Setting value [Off]: Uses the previous rasterizing method. [On]: Uses the special rasterizing method. Restrictions
General precaution If [On] is selected, pages with many transparency attributes may not be printed correctly. |
168 | If PDF data (with transparency attributes or overprinting used frequently) using a large amount of memory is printed from AccurioPro Hot Folder when RIP is performed using APPE, output is completed at the second page in certain cases. No problem occurs in CPSI. | This problem may be resolved by switching the output method. Setting value [Off]: By Job [On]: By Page Restrictions
Important After the setting is changed, turn Main power switch off, and on again to confirm the setting. |
169 | When a specific APPE job (PDF) is printed from AccurioPro Hot Folder, white or black lines appear on the printed image. No problem occurs in CPSI. | This problem may be resolved by switching the cache of the APPE display list. Setting value [Off]: Enable [On]: Disable Restrictions
Important After the setting is changed, turn Main power switch off, and on again to confirm the setting. General precaution If [On] is selected, performance may decrease. |
174 | The "Jog" command should be supported to try page offset at arbitrary intervals. | Setting value [Off]: Does not support the Jog command. [On]: Supports the Jog command. Restrictions
|
175 | Offset by Job Unit should be performed so that banner pages and the body are located at the same output position when a printer job with banner pages is sent. | Setting value [Off]: Does not perform offset. [On]: Performs offset. Restrictions
|
176 | A job with front and back covers should be printed immediately without being spooled. | Setting value [Off]: Spools a job in the controller. [On]: Does not spool a job in the controller. General precaution Setting to [On] does not support the back cover profile. If [On] is selected, the following profile setting is not applied correctly.
If [On] is selected, the following function is not applied correctly.
|
177 | When the user uses the following IP address, the network in user environment cannot be used. IP address: 172.17.0.1 | This phenomenon occurs because "172.17.0.1" is used as the internal address of AccurioPro Print Manager. Setting to [On] allows you to change the internal address. Setting value [Off]: 172.17.0.1/16 [On]: 192.168.1.5/24 |
178 | When a job (PS or PDF) created with the user's Knapp application is printed continuously, an error page may be inserted among pages. | The supported Readback command causes such an error, so this problem may be resolved by setting to "Other PJL Commands". Setting value [Off]: Support the Readback command. @PJL ECHO @PJL INFO [On]: Supports other PJL commands. @PJL USTATUS @PJL USTATUSOFF |
181 | When the interpreter is CPSI, data should be reloaded. | Setting value [Off]: Does not reload. [On]: Reloads. |
182 | "Default Manual Settings" configured in Color Centro should be forcibly applied when a job is held. | Setting value [Off]: Not applied forcibly. [On]: Applied forcibly. Restrictions
|
183 | When a PDF file including form objects is printed, part of the data is missing. | This problem may be resolved by switching the processing method. Setting value [Off]: Inline expansion [On]: Form expansion Restrictions
|
184 | [All] is only selectable for [Object Type] in [Tone Curve Adjustment...] of AccurioPro Print Manager. | Set to [On]; [Image] or [Text/Graphics] becomes selectable. Setting value [Off]: [All] is only selectable. [On]: [All], [Image], or [Text/Graphics] is selectable. |
189 | When printing is performed with AccurioPro Print Manager, the [Range] setting should be kept for printing even when job selection - right-click - [Print...] is performed for printing. | Save [Range] that is set by selecting [Job Management] - [Job Settings...] - [General] - [Printing Pages]. When reprinting, you can apply the saved [Range]. Setting value [Off]: Does not apply the saved value when storing or printing. [On]: Applies the saved value when storing or printing. Restrictions
|
190 | Unable to send to Hot Folder in AccurioPro Print Manager (mainly from Mac OS). | This issue may be resolved by increasing the file monitoring cycle interval for Hot Folder. Setting value [Off]: Does not increase the file monitoring cycle interval. [On]: Does increase the file monitoring cycle interval. Important
|
197 | You should notify the user that re-RIP is required with AccurioPro Print Manager. | Make a setting to switch the re-RIP display when printing from AccurioPro Print Manager. Setting value [Off]: Does not display a confirmation dialog box when performing re-RIP. [On]: Displays a confirmation dialog box when performing re-RIP. |
198 | When printing a job that requires re-RIP by specifying a page, the larger the page number, the longer it takes from the job receiving to the paper output. | By re-RIPing and printing only the specified page, you can shorten the time period from when the job is received to when paper is output. Setting value [Off]: Saves all the RIPed editing contents (images, thumbnails, and job ticket contents). [On]: Does not save all the RIPed editing contents. |
199 | Annotations in a PDF file are printed when the Direct Printing is carried out. It should be possible to select whether to print an annotation in a PDF file. | Setting value [Off]: Prints an annotation in a PDF file. [On]: Does not print an annotation in a PDF file. Restrictions
|