Associating with Other Systems or Applications

[ON]/[OFF]

Select whether to use SNMP.

[ON] is specified by default.

[SNMP v1/v2c(IP)]

Select whether to use SNMP v1 or SNMP v2.

[ON] is specified by default.

[SNMP v3(IP)]

Select whether to use SNMP v3.

[ON] is specified by default.

[SNMP v1(IPX)]

Select whether to use SNMP v1 in the IPX environment.

[ON] is specified by default.

[UDP Port Number]

If necessary, change the UDP port number.

Normally, you can use the original port number.

[161] is specified by default.

[SNMP v1/v2c Settings]

Tap [SNMP v1/v2c Settings] to configure SNMP v1 or v2c settings.

• [Read Community Name Settings]: Enter a read-only community name (using up to 15 characters). [public] is specified by default.

• [Write Setting]: Select whether to enable the read and write functions. [Enable] is specified by default.

• [Write Community Name Settings]: If [Write Setting] is set to [Enable], enter the community name in the read-write enable state (using up to 15 characters). [private] is specified by default.

[SNMP v3 Settings]

Tap [SNMP v3 Settings] to configure SNMP v3 settings.

• [Context Name Settings]: Enter the context name (using up to 63 characters).

• [Discovery User Permissions]: Select whether to allow a discovery user. [ON] is specified by default.

• [Discovery User Name Settings]: If [Discovery User Permissions] is set to [ON], enter the discovery user name (using up to 32 characters). [public] is specified by default.

• [Read User Name Settings]: Enter the read-only user name (using up to 32 characters). [initial] is specified by default.

• [Security Level]: Select a security level for the read-only user. [auth-password/priv-password] is specified by default.

• [Write User Name Settings]: Enter the user name of the user in the read-write enable state (using up to 32 characters). [restrict] is specified by default.

• [Security Level]: Select a security level of the user in the read-write enable state. [auth-password/priv-password] is specified by default.

• [Password Setting]: Enter the authentication password and privacy password of users in the read-only state and read-write enable state.

• [Encryption Algorithm]: Select an encryption algorithm. [DES] is specified by default.

• [Authentication Algorithm]: Select an authentication algorithm. [MD5] is specified by default.

[TRAP Setting]

Select whether to allow a notification of the status of this machine using the SNMP TRAP function.

[Allow] is specified by default.

[TRAP Setting When Authentication Failed]

Select whether to send TRAP when authentication fails.

[Invalid] is specified by default.

[ON]/[OFF]

Select whether to use SSDP.

[ON] is specified by default.

[Multicast TTL Setting]

Change TTL (Time To Live) for SSDP multi-cast packet if necessary.

[1] is specified by default.

[ON]/[OFF]

Select whether to use SNMP.

[ON] is specified by default.

[SNMP v1/v2c(IP)]

Select whether to use SNMP v1 or SNMP v2.

[ON] is specified by default.

[SNMP v3(IP)]

Select whether to use SNMP v3.

[ON] is specified by default.

[SNMP v1(IPX)]

Select whether to use SNMP v1 in the IPX environment.

[ON] is specified by default.

[UDP Port Number]

If necessary, change the UDP port number.

Normally, you can use the original port number.

[161] is specified by default.

[SNMP v1/v2c Settings]

Tap [SNMP v1/v2c Settings] to configure SNMP v1 or v2c settings.

• [Read Community Name Settings]: Enter a read-only community name (using up to 15 characters). [public] is specified by default.

• [Write Setting]: Select whether to enable the read and write functions. [Enable] is specified by default.

• [Write Community Name Settings]: If [Write Setting] is set to [Enable], enter the community name in the read-write enable state (using up to 15 characters). [private] is specified by default.

[SNMP v3 Settings]

Tap [SNMP v3 Settings] to configure SNMP v3 settings.

• [Context Name Settings]: Enter the context name (using up to 63 characters).

• [Discovery User Permissions]: Select whether to allow a discovery user. [ON] is specified by default.

• [Discovery User Name Settings]: If [Discovery User Permissions] is set to [ON], enter the discovery user name (using up to 32 characters). [public] is specified by default.

• [Read User Name Settings]: Enter the read-only user name (using up to 32 characters). [initial] is specified by default.

• [Security Level]: Select a security level for the read-only user. [auth-password/priv-password] is specified by default.

• [Write User Name Settings]: Enter the user name of the user in the read-write enable state (using up to 32 characters). [restrict] is specified by default.

• [Security Level]: Select a security level of the user in the read-write enable state. [auth-password/priv-password] is specified by default.

• [Password Setting]: Enter the authentication password and privacy password of users in the read-only state and read-write enable state.

• [Encryption Algorithm]: Select an encryption algorithm. [DES] is specified by default.

• [Authentication Algorithm]: Select an authentication algorithm. [MD5] is specified by default.

[TRAP Setting]

Select whether to allow a notification of the status of this machine using the SNMP TRAP function.

[Allow] is specified by default.

[TRAP Setting When Authentication Failed]

Select whether to send TRAP when authentication fails.

[Invalid] is specified by default.

[TCP Socket]

Configure settings to establish a communication with this machine via TCP Socket.

For details, refer to Here.

[TCP Socket (ASCII Mode)]

Configure settings to establish a communication with this machine via TCP Socket (ASCII Mode).

Enabling TCP Socket (ASCII Mode) displays Web Connection in the flash view.

For details, refer to Here.

[ON]/[OFF]

Select whether to use the FTP server function of this machine.

[ON] is specified by default.

[Deny Reception Command]

Select a command to deny a receiving job from an FTP client when using the FTP server of this machine.

Set this option to return an error when a PORT/EPRT command or PASV/EPSV command is sent from an FTP client to this machine.

[Allow] is specified by default.

[PORT Command Enhanced Security]

Select whether to enable the security of this machine against FTP bounce attacks. This option is not available if [Deny Reception Command] is set to [PORT/EPRT].

When a PORT/EPRT command is sent from an FTP client, the data connection is established only if both of the following conditions are satisfied:

• A port number less than 1024 is not specified.

• The IP address specified by the command is same as that specified when a control connection is established.

[Enable] is specified by default.

[ON]/[OFF]

Select whether to use the WebDAV server function of this machine.

[OFF] is specified by default.

[SSL Settings]

Specify whether to use the SSL for communication or not.

• [Non-SSL Only]: Only non-SSL communication is allowed.

• [SSL Only]: Only SSL communication is allowed.

• [SSL/Non-SSL]: Both SSL communication and non-SSL communication are allowed.

[Non-SSL Only] is specified by default.

[Password Setting]

Specify the password to restrict access to the WebDAV server of this machine (using up to 64 characters).

Tapping [Initial Password] returns the password to the default.

[sysadm] is specified by default.

[Import/Export User Data]

Specify whether to allow importing/exporting of the destinations registered on this machine (one-touch destinations, groups, and programs), authentication information from the remote diagnosis system.

[Restrict] is specified by default.

[ON]/[OFF]

Select whether to use a proxy server when using the remote diagnosis system.

[OFF] is specified by default.

[WebDAV Client Settings and Synchronization]

Select this option to use the proxy server registered in [WebDAV Client Settings] as a proxy server for remote diagnosis.

[WebDAV Client Settings and Synchronization] is specified by default.

[Individual Settings]

Select this option to register a proxy server for remote diagnosis separately from the proxy server registered in [WebDAV Client Settings].

[Proxy Server Address]

Enter the proxy server address.

Use one of the following formats.

• Example of host name entry: "host.example.com"

• Example of IP address (IPv4) entry: "192.168.1.1"

• Example of IP address (IPv6) entry: "fe80::220:6bff:fe10:2f16"

[Proxy Server Port Number]

If necessary, change the proxy server port number. Normally, you can use the original port number.

[8080] is specified by default.

[User Name]

Enter the user name to log in to the proxy server (using up to 63 characters).

[Password]

Enter the password of the user name you entered into [User Name] (using up to 63 characters).

[ON]/[OFF]

Select whether to use the ThinPrint function.

Select [ON] to use this machine as ThinPrint Client (.print Client).

[ON] is specified by default.

[Port Number]

Enter the port number of ThinPrint Engine (.print Engine) to be connected.

[4000] is specified by default.

[Data Size before Compression]

Specify the maximum packet size to compress data in the ThinPrint Engine (.print Engine) side.

ThinPrint Engine (.print Engine) compresses data in these sizes before sending a print job to this machine.

[8192] is specified by default.

[Connection Timeout]

Enter the connection timeout period to send a print job from ThinPrint Engine (.print Engine).

[90] is specified by default.

[Printer Name]

Enter the printer name of this machine to be used in ThinPrint Engine (.print Engine).

[Printer Class Name]

Enter the printer class name of this machine to be used in ThinPrint Engine (.print Engine).

[Certificate Verification Level Settings]

To verify the certificate, select items to be verified.

• [Expiration Date]: Confirm whether the certificate is within the validity period. [Confirm] is specified by default.

• [Key Usage]: Confirm whether the certificate is used according to the intended purpose approved by the certificate issuer. [Do Not Confirm] is specified by default.

• [Chain]: Confirm whether there is a problem in the certificate chain (certificate path). The chain is validated by referencing the external certificates managed on this machine. [Do Not Confirm] is specified by default.

• [Expiration Date Confirmation]: Confirm whether the certificate has expired. [Do Not Confirm] is specified by default.

• [CN]: Confirm whether CN (Common Name) of the certificate matches the server address. [Do Not Confirm] is specified by default.

[Connection Service Setting]

Select whether to use Connection Service. [OFF] is specified by default.

If [ON] is selected, configure the following settings.

• [Server Address]:Enter the address of the server that supplies Connection Service.

• [Port Number]Enter the number of the port that is used for Connection Service.

• [AYT Interval]:Enter the reconnection interval to check Connection Service operations in seconds. [60] is specified by default.

• [Client ID]:Enter the client ID of this machine to be used for Connection Service. [1] is specified by default.

• [Authentication Key]:Enter the authentication key used to connect to Connection Service. [0] is specified by default.

[Checking Connection Service Setting]

Displays the status of the connection with Connection Service.

[Connection Method]

Compresses image data of the Control Panel of this machine before sending it to a tablet terminal.

Select whether to give priority to the operation speed at a tablet terminal or give priority to the image quality of the tablet terminal screen.

[Standard] is specified by default.

[Connection Timeout]

If necessary, change the timeout period to close a communication with a tablet terminal.

[20] minutes is selected by default.

[Remote Operation Switch Confirmation]

Select whether to display the screen for checking whether to continue a remote operation on the screen of a tablet terminal when the Control Panel of this machine has been touched while a remote operation is being performed using a tablet terminal.

[OFF] is specified by default.