List of Adjustment Menu Items
|
Adjustment item and description |
Objects/range of adjustment |
||||
|---|---|---|---|---|---|
|
[01 Machine Adjustment] |
|||||
|
[01 Printer Adjustment] |
|||||
|
[01 Restart Timing Adjustment] Adjust the image position of lead edge in paper feed direction in the printer engine. Prerequisite: FD-Mag. Adjustment is completed. |
Objects of adjustment: Side1: All Trays Offset Adjustment Range: (Lower) -45 to +45 (Higher) (1 step = 0.1 mm)
Objects of adjustment: Side1: Restart Timing (Tray 1 to Tray 5), Restart Timing (Bypass) Side2: Restart Timing (Tray 1 to Tray 5), Restart Timing (Bypass) Adjustment Range: (Lower) -30 to +30 (Higher) (1 step = 0.1 mm) |
||||
|
[02 Centering Adjustment] Adjust the image position in the crosswise direction of the printer engine. Prerequisite: CD-Mag. Adjustment is completed. |
Adjustment Range: (Front) -64 to +63 (Back) (1 step = 0.1 mm) |
||||
|
[03 FD-Mag. Adjustment] Adjust the magnification in paper feed direction in the printer engine. |
Objects of adjustment: Side1: Printer FD-Mag. Adjustment Range: (Short) -10 to +10 (Long) (1 step = 0.05%)
Objects of adjustment: Side2: Tray 1 to Tray 5, Bypass Tray Adjustment Range: (Short) -10 to 0 (Long) (1 step = 0.05%) |
||||
|
[04 CD-Mag. Adjustment] Adjust the magnification in crosswise direction in the printer engine. |
Objects of adjustment: Side1: Printer CD-Magnification Adjustment Adjustment Range: (Short) -10 to +10 (Long) (1 step = 0.05%) Objects of adjustment: Side2: Tray 1 to Tray 5, Bypass Tray Adjustment Range: (Short) -10 to 0 (Long) (1 step = 0.05%) |
||||
|
[02 Scan Adjustment] |
|||||
|
[01 Restart Timing Adjustment] Adjust the scan starting position when scanning the original on the original glass. Prerequisite: FD-Mag. Adjustment is completed. |
Adjustment Range: -30 (Image Slow) to +30 (Image Fast) (1 step = 0.1 mm) |
||||
|
[02 Centering Adjustment] Adjust the image position in the crosswise direction when scanning the original on the original glass. Prerequisite: Printer Centering Adjustment is completed. |
Objects of adjustment: Orig. Glass Centering Adjustment Range: -57 (Back) to +57 (Front) (1 step = 0.1 mm) |
||||
|
[03 FD-Mag. Adjustment] Adjust the magnification in feed direction when scanning the original on the original glass. Prerequisite: Printer FD-Mag. Adjustment is completed. |
Adjustment Range: 990 (Short) to 1010 (Long) (1 step = |
||||
|
[04 CD-Mag. Adjustment] Adjust the magnification in the crosswise direction when scanning the original from the original glass. Prerequisite: Printer FD-Mag. Adjustment is completed. |
Adjustment Range: 990 (Short) to 1010 (Long) (1 step = |
||||
|
[03 LPH Adjustment] |
|||||
|
[01 Gap Adjustment Between LPH Chips] Adjust the gap (39 points) between LPH chips. |
Adjustment Range: (Lighter) -8 to +8 (Darker) (1 step = 1.0%) Select Test Pattern: Dark Gray, Light Gray Line Draw: ON, OFF All Offset |
||||
|
[02 Finisher Adjustment] (Finisher FS-532) This menu item is displayed and can be set on the machine mounted with Finisher FS-532. |
|||||
|
[01 Staple Finisher Adjustment] [01 Staple Finisher(Main) Adj.] |
|||||
|
[01 Staple Position Adjustment] Adjust 2 position staple pitch and corner staple positions in the staple finisher. |
Objects of adjustment: 2 Position Pitch (120 mm), 2 Position Pitch (140 mm), 2 Position Pitch (165 mm), Rear Diagonal Adjustment Range: -5 (Narrow) to +5 (Wide) (1 step = 1 mm) Objects of adjustment: Rear Parallel, Front Parallel Adjustment Range: -3 (Narrow) to +3 (Wide) (1 step = 1 mm) |
||||
|
[02 Staple Paper Width Adj.] Adjust the board alignment width of the staples in the staple finisher. |
Objects of adjustment: Offset for All Size, SRA3 * SRA4 Adjustment Range: -20 (Wide) to +20 (Narrow) (1 step = 0.1 mm) |
||||
|
[03 FD Alignment Plate Adj.] Adjust the vertical alignment fitting for staples in the staple finisher. |
Objects of adjustment: Offset for All Size, A4 Adjustment Range: -50 (Wide) to +50 (Narrow) (1 step = 0.1 mm) |
||||
|
[04 Exit Guide Paper Width Adj.] Adjust the exit guide alignment pitch to be used by the staple finisher. Make adjustment if output paper stack on main tray is uneven in straight delivery. |
Objects of adjustment: Offset for All Size, SRA3 * SRA4 Adjustment Range: -50 (Wide) to +50 (Narrow) (1 step = 0.1 mm) |
||||
|
[05 Rewind Paddle Descent Adj.] Adjust rewind paddle descent. |
Objects of adjustment: Offset for All Size, SRA3 * SRA4 Adjustment Range: -10 (Little) to +10 (Much) (1 step = 0.2 mm) |
||||
|
[06 Rewind Function Operation] Select operation for the rewind paddle. |
Auto, ON, OFF |
||||
|
[07 Upper Gripper Operation] Select the upper gripper operation for main tray delivery exit. |
Auto, ON, OFF |
||||
|
[08 Output Alignment Operation] Select operation for output alignment. |
Auto, ON, OFF |
||||
|
[02 Staple Finisher(Fold) Adj.] This menu item is to be displayed and become configurable on Finisher FS-532 mounted with Saddle Stitcher SD-510. |
|||||
|
[01 Fold&Staple Pitch Adjustment] Adjust staple pitch in Saddle Stitcher SD-510. Make this adjustment if staple pitch is not within the allowance range. |
Objects of adjustment: Offset for All Size, SRA3 Adjustment Range: -300 (Narrow) to +300 (Wide) (1 step = 0.1 mm) |
||||
|
[02 Fold&Staple Paper Width Adj.] Adjust pitch of alignment plate in Saddle Stitcher SD-510 if half-folded or multi tri-folded paper show misalignment in the crosswise direction to paper feeding. |
Objects of adjustment: Offset for All Size, SRA3 Adjustment Range: -50 (Narrow) to +50 (Wide) (1 step = 0.1 mm) |
||||
|
[03 Fold & Staple Staple Position] Adjust staple position in Saddle Stitcher SD-510. |
Objects of adjustment: Offset for All Size, SRA3 Adjustment Range: -50 (Extend) to +50 (Shorten) (1 step = 0.1 mm) |
||||
|
[04 Fold & Staple Fold Position] Adjust half-fold position of fold & staple function in Saddle Stitcher SD-510. Make this adjustment if half-fold position is not within the specified range. |
Objects of adjustment: Offset for All Size, SRA3 Adjustment Range: -50 (Extend) to +50 (Shorten) (1 step = 0.1 mm) |
||||
|
[05 Half-Fold Fold Position Adj.] Adjust half-fold position of fold function in Saddle Stitcher SD-510. |
Objects of adjustment: Offset for All Size, SRA3 Adjustment Range: -50 (Extend) to +50 (Shorten) (1 step = 0.1 mm) |
||||
|
[06 Tri-Fold Adjustment] |
|||||
|
[01 Tri-Fold Position Adjustment] Adjust Fold 1 and Fold 2 positions for multi tri-folding in Saddle Stitcher SD-510. Make this adjustment if each fold position for tri-folding is not within the allowance range. |
Objects of adjustment: 8.5 Adjustment Range: Fold 1: -50 (Extend) to +50 (Shorten) (1 step = 0.1 mm) Fold 2: -50 (Shorten) to +50 (Extend) (1 step = 0.1 mm) |
||||
|
[02 Double Fold Plate Adjustment] Adjust double fold plate in saddle stitcher. Make the insertion deeper if the Fold 2 misalignment is large. |
Objects of adjustment: 8.5 Adjustment Range: -50 (Shallow) to +50 (Deep) (1 step = 0.1 mm) |
||||
|
[07 Half-Fold Strength Adj.] To suppress the opening of booklets, increase the roller pressure time. - You cannot adjust the strength to fold booklets. - Long pressure time causes less productivity. |
Adjustment Range: (Additional time) 0 to +10 (1 step = 1 sec) |
||||
|
[03 Staple Finisher (Punch) Adj.] This menu item is to be displayed and configurable on Finisher FS-532 mounted with Punch Kit PK-522. |
|||||
|
[01 Vertical Position Adj.(CD)] Adjust the misalignment in center positions of paper and punch holes for each paper size. |
Objects of adjustment: Offset for All Size, A3 Adjustment Range: -50 (Forward) to +50 (Backward) (1 step = 0.1 mm) |
||||
|
[02 Horizontal Position Adj.(FD)] Adjust the distance between the edge of the printed paper and the center of punch holes. |
Objects of adjustment: Offset for All Size, A3 Adjustment Range: -50 (Far) to +50 (Close) (1 step = 0.1 mm) |
||||
|
[03 Registration Adjustment] If the punch position is not parallel to the paper edge, control the paper curl and wrinkle by adjusting the paper loop amount of the registration roller. |
Objects of adjustment: Back on Top Output, ADU Feed Adjustment Range: -50 (Short) to +50 (Long) (1 step = 0.1 mm) |
||||
|
[04 Staple Finisher (PI) Adj.] This menu item is to be displayed and configurable on Finisher FS-532 mounted with PostInserter PI-502. |
|||||
|
[01 PI Registration Adjustment] When paper fed from the upper or lower tray of PostInserter PI-502 has skew or wrinkle, or causes paper jam, adjust the paper loop of the registration roller. |
Objects of adjustment: PI Upper Tray, PI Lower Tray Adjustment Range: -5 (Short) to +5 (Long) (1 step = 1.0 mm) |
||||
|
[02 Finisher Adjustment] (Z Folding Unit ZU-608 mounted) This menu item is to be displayed and become configurable on Finisher FS-532 mounted with Z-Folding Unit ZU-608. |
|||||
|
[02 Z-Folding Unit Adjustment] |
|||||
|
[01 Z-Fold Position Adjustment] Adjust the fold positions for Z-folding. Adjust Fold 1 and Fold 2 in this order. |
Objects of adjustment: Offset for All Size, A3 Adjustment Range: Fold 1: (Shorten) -128 to +127 (Extend) (1 step=0.1 mm) Fold 2: (Shorten) -128 to +127 (Extend) (1 step=0.1 mm) |
||||
|
[02 Punch Adjustment] |
|||||
|
[01 Vert. Position Adj.(CD)] Adjust depth of punch position in Z-Folding Unit ZU-608 |
Objects of adjustment: Offset for All Size, A3 Adjustment Range: (Forward) -50 to +50 (Backward) (1 step=0.1 mm) |
||||
|
[02 Horiz. Position Adj.(FD)] Adjust punch position for transport direction in Z-Folding Unit ZU-608. |
Adjustment Range: (Close) -50 to +50 (Far) (1 step=0.1 mm) |
||||
|
[03 Punch Registration Loop Adj.] If punch position of punch unit is not parallel to paper edge in Z-Folding Unit ZU-608, control paper curl and wrinkle by adjusting paper loop of registration roller. |
Objects of adjustment: Back on Top Output, ADU Feed Adjustment Range: (Short) -20 to +20 (Long) (1 step = 0.8 mm) |
||||
|
[02 Finisher Adjustment] (Output Tray OT-510) This menu item is displayed and can be set on the machine mounted with Output Tray OT-510. |
|||||
|
[01 Staple Finisher Adjustment] [01 Staple Finisher(Main)Adj.] |
|||||
|
[04 Exit Guide Paper Width Adj.] Adjust the exit guide alignment pitch to be used by the staple finisher. |
Objects of adjustment: Offset for All Size, SRA3 Adj. Range: -50 to +50 1 step = 0.1 mm - (Wide) + (Narrow) * SRA4 |
||||
|
[07 Upper Gripper Operation] Select the upper gripper operation for main tray delivery exit. |
[Auto], [ON], [OFF] |
||||
|
[08 Output Alignment Operation] Select operation for output alignment. |
[Auto], [ON], [OFF] |
||||
|
[02 Finisher Adjustment] (Output Tray OT-512) This menu item is displayed and can be set on the machine mounted with Output Tray OT-512. |
|||||
|
[01 Staple Finisher Adjustment] [01 Staple Finisher(Main)Adj.] |
|||||
|
[01 Exit Guide Paper Width Adj.] Adjust the exit guide alignment pitch to be used by the staple finisher. |
Objects of adjustment: Offset for All Size, SRA3 Adj. Range: -50 to +50 1 step = 0.1 mm - (Wide) + (Narrow) |
||||
|
[02 Upper Gripper Operation] Select the upper gripper operation for main tray delivery exit. |
[Auto], [ON], [OFF] |
||||
|
[03 Output Alignment Operation] Select operation for output alignment. |
[Auto], [ON], [OFF] |
||||
|
[03 ADF Adjustment] |
|||||
|
[01 ADF Original Stop Pos. Adj.] Adjust the position to start scanning on the ADF and the image
position in the crosswise direction. |
Objects of adjustment: Restart Timing (Front), Restart Timing (Back) Adjustment Range: -40 (Image Fast) to +40 (Image Slow) Objects of adjustment: Centering (Front), Centering (Back) Adjustment Range: -44 (Front) to +44 (Back) |
||||
|
[02 ADF Orig. Stop Pos. Auto] Automatically adjust the position to start scanning on the ADF
and the image position in crosswise direction. |
Objects of adjustment: Restart Timing (Front), Restart Timing (Back), Start |
||||
|
[03 FD-Mag. Adjustment] Adjust the magnification in paper feed direction when scanning on the ADF. |
Objects of adjustment: ADF Adjustment Range: -20 (Short) to +20 (Long) |
||||
|
[04 FD-Mag. Auto Adjustment] Automatically adjust the magnification in paper feed direction when scanning on the ADF. |
Objects of adjustment: ADF Start |
||||
|
[05 Home Read Position Adj(Back)] Adjust the home position of the shading shaft to correct any image failure due to dirt on the shading shaft on the back side of the ADF. |
Adjustment Range: -4 to +4 (1 step = 1) |
||||
|
[06 FD-Mag. Adjustment(Back)] Adjust the magnification in paper feed direction on the back side when scanning on the ADF. Prerequisite: Printer FD-Mag. Adjustment is completed. |
Objects of adjustment: ADF Adjustment Range: (Short) -20 to +20 (Long) (1 step = 0.1 %) |
||||
|
[07 FD-Mag. Auto Adj.(Back)] Automatically adjusts the magnification in paper feed direction on the back side when scanning on the ADF. |
Objects of adjustment: ADF Start |
||||
|
[08 Main Scan Dir. Zoom(Back)] Adjust the magnification in crosswise direction on the back side when scanning on the ADF. Prerequisite: Printer CD-Mag. Adjustment is completed. |
Objects of adjustment: ADF Adjustment Range: (Short) -10 to +10 (Long) (1 step = 0.1 %) |
||||
|
[09 Main ScanDir.Zoom Auto(Back)] Automatically adjusts the magnification in crosswise direction on the back side when scanning on the ADF. |
Objects of adjustment: ADF Start |
||||
|
[04 Size Memory Recovery Mode] Perform drum pre-rotation for one minute. |
Start |
||||
|
[05 Charge Manual Cleaning] Perform charging corona cleaning. |
Start |
||||
|
[06 Drum Memory Recovery Mode] Perform drum pre-rotation for 3 minutes. |
Start |
||||
|
[07 Drum Refresh Mode] Refresh surface by rotating drum. |
Start |
||||
|
[08 Gamma Automatic Adjustment] Perform gamma automatic adjustment. |
Start |
||||
|
[09 Density Balance Auto. Adj.] Perform the density balance adjustment using the scan function. |
Output Chart Start |
||||
