Layout

[Combination]

[2-in-1], [4-in-1], [6-in-1], [9-in-1], [16-in-1]

[2 x 2], [3 x 3], [4 x 4]

Prints multiple pages onto a single sheet by reducing the size of the document. Or prints one page onto multiple sheets by enlarging the size of the document.

[Combination Details]

-

Select the condition of combination.

For details, refer to "Combination Details" shown below.

[Imposition]

[2 Repeat], [2 Repeat Reversal (U)], [2 Repeat Reversal (D)], [2 Repeat Reversal (L)], [2 Repeat Reversal (R)], [2 in 1], [4 Repeat], [4 in 1 (Vertical)], [4 in 1 (Horizontal)] ,[8 Repeat]

Set this to perform an imposition printing.

Outputs onto paper in twice or quadruple the size specified in the [Original Size].

For example : When the [Paper Size] is A4, the document is printed with A3 sheet.

[Rotate 180]

Off, On

Select this check box to rotate the document 180° to print.

[Skip Blank Pages]

Off, On

Set this not to print blank pages.

[Chapters]

Off, On

Set this to print page on the front side of paper. It can be specified when Print Type is other than [1-Sided].

[Print Position Settings]

[Left], [Center], [Right]

Specify the print position.

[Print Type]

[1-Sided], [2-Sided], [Booklet], [Booklet (Original Size 2)]

Select a print type.

[Print Type Details]

-

Specify [Booklet Splitting], [Book Spread], and [Adhesive binding]. For details, refer to "Details of Print Types" shown below.

[Binding Position]

[Auto], [Left Bind], [Right Bind], [Top Bind]

Set this to specify the binding position.

[Image Shift]

Off, On

Set this to print shifting the position of the entire image within the paper.

You can specify the shift width in the [Image Shift Settings].

[Image Shift Settings]

-

You can specify detail settings of the image shift.

For details, refer to "Image Shift Settings" shown below.

[Tab Image Shift]

Off, On

Set this to print shifting the position of the entire image within the tab paper.

It can be specified when the original size is A4, or Letter.

You can specify the detail of the shift width in the [Tab Image Shift settings]

[Tab Image Shift Settings]

Shift Settings

Specify the shift width to print shifting the position of the entire image within the tab paper.

[Combination]

[2 in 1], [4 in 1], [6 in 1], [9 in 1], [16 in 1], [2 2], [3 3], [4 4]

Prints multiple pages onto a single sheet by reducing the size of the document. Or prints one page onto multiple sheets by enlarging the size of the document.

[Layout Order]

[Left-to-Right], [Right-to-Left], [Top-to-Bottom], [Bottom-to-Top], [Sideways from Upper -Left], [Downward from Upper -Left], [Sideways from Upper -Right], [Downward from Upper -Right]

Specify the order of the page arrangement. It can be set when the N in 1 is specified in the Combination.

[Border]

[Frame], [Line]

Specify whether you use the border or not. If you use, specify the border type. It can be set when the N in 1 is specified in the Combination.

[Overlap width line]

Off, On

Set this to print a reference line for taping together printed pages. It can be set when N N is specified in the Combination.

[Booklet Splitting]

Off, On

Used to split one job into two or more booklets.

[Pages per Section]

1 - 9999

Enter the number of pages in one booklet that is split.

It inserts a blank page automatically if the value for [Booklet Splitting] is not a multiple of 4.

[Book Spread]

Off, On

Prints original data of different paper sizes in book spread.

[Adhesive Binding]

Off, On

Prints data in the page order like a book when each sheet is folded in half after printing.

[Front Side]/[Back Side]

-

Specify the shift direction and the shift width. When you remove the check from the [Same value for front and back ] on 2-Sided printing, you can specify the width to the front and the back respectively.

[Right]

- 250.0 mm to 250.0 mm / -9.84" to +9.84"

Shifts the position of the printing image with the specified amount to the left/right.

[Top]

- 250.0 mm to 250.0 mm / -9.84" to +9.84"

Shifts the position of the printing image with the specified amount to the top/bottom.

[Imposition] - [Page Interval]

- 250.0 mm to 250.0 mm / -9.84" to +9.84"

Specify the page space.

When you specify the negative value (-), pages will be overlapped with the specified width.

[For [Booklet] or [Adhesive binding]] - [Page space]

- 250.0 mm to 250.0 mm / -9.84" to +9.84"

Specify the page space.

When you specify the negative value (-), pages will be overlapped with the specified width.

[For [Booklet] or [Adhesive binding]] - [High Precision]

Off, On

Specify this option to enhance the precision of the page space shift amount. When High Precision is selected, the page space in the back side is set to the same value as for the front side.

[For [Booklet] or [Adhesive binding]] - [Creep Adjustment]

0.00 mm to 50.00 mm / 0.00" to 1.97"

Adjusts so that the page space is narrowed inward, taking into account the thickness of the paper after it has been folded.

[For [Booklet] or [Adhesive binding]] - [Object]

Specify the object for Creep Adjustment.

[Single Page]

Sets the value of [Creep Adjustment] as the offset amount for each sheet.

[All Pages]

Sets the value of [Creep Adjustment] as the total offset amount from the outermost sheet to the innermost paper. The offset amount for each sheet is automatically obtained from the specified total amount depending on the number of printed sheets.