[Paper Type]

Select the type of paper that is used to adjust the start position for printing.

[Adjust Value]

Enter the adjustment value between -3.0 mm and 3.0 mm (default: [0.0 mm]).

[Select Tray]

Select a paper tray that is used to adjust the start position for printing.

[Adjust Value]

Enter the adjustment value between -3.0 mm and 3.0 mm (default: [0.0 mm]).

[Paper Type]

Select the type of paper that is used to adjust the start position for printing.

[Adjust Value]

Enter the adjustment value between -3.0 mm and 3.0 mm (default: [0.0 mm]).

[Select Tray]

Select a paper tray that is used to adjust the start position for printing.

[Adjust Value]

Enter the adjustment value between -3.0 mm and 3.0 mm (default: [0.0 mm]).

[600dpi Front]/[600dpi Back]/[1200dpi Front]/[1200dpi Back]

Select the side of paper subject to defect adjustment depending on the resolution.

• [600dpi Front]/[1200dpi Front]: Select this option if defective images exist on the front side of 1-sided or 2-sided printing with the 600 dpi or 1200 dpi resolution.

• [600dpi Back]/[1200dpi Back]: Select this option if defective images exist on the back side of 2-sided printing with the 600 dpi or 1200 dpi resolution.

[Paper Type]

Select the type of paper that is used to adjust defects.

[Adjust Value]

Enter the adjustment value between -8 and 7 (default: [0]).

Increase the value if roughness is detected on a print image, and reduce it if voids or white spots are detected on a print image.

[Paper Size]

Select the size of paper that is used to adjust the staple position.

[Adjust Value]

Enter the adjustment value between -10.0 mm and 10.0 mm (default: [0.0 mm]).

Increase the value when moving the staple position rightward, and reduce it when moving the staple position leftward.

[Paper Size]

Select the size of paper that is used to adjust the fold position.

[Adjust Value]

Enter the adjustment value between -10.0 mm and 10.0 mm (default: [0.0 mm]).

Increase the value when moving the folding position rightward, and reduce it when moving the folding position leftward.

[Paper Size]

Select the size of paper that is used to adjust the fold position.

[Adjust Value]

Enter the adjustment value between -10.0 mm and 10.0 mm (default: [0.0 mm]).

Increase the value when moving the folding position rightward, and reduce it when moving the folding position leftward.

[Paper Size]

Select the size of paper that is used to adjust the fold position.

[Adjust Value]

Enter the adjustment value between -10.0 mm and 10.0 mm (default: [0.0 mm]).

Increase the value when moving the folding position rightward, and reduce it when moving the folding position leftward.

[Paper Size]

Select the size of paper subject to punch hole position adjustment.

[Adjust Value]

Enter the adjustment value between -5.0 mm and 5.0 mm (default: [0.0 mm]).

Increase the value when moving the punching hole upward, and reduce it when moving the punching hole downward.

[Finisher]/[Post Inserter]

Select the position subject to punch hole position adjustment.

• [Post Inserter]: An adjustment is possible when the Post Inserter is installed on the machine.

[Adjust Value]

Enter the adjustment value between -5.0 mm and 5.0 mm (default: [0.0 mm]).

Increase the value when moving the punching hole rightward, and reduce it when moving the punching hole leftward.

[Paper Type]

Select the type of paper subject to punch hole position adjustment.

[Adjust Value]

Enter the adjustment value between -10 and 10 (default: [0]).

Increase the value when moving the punching hole rightward, and reduce it when moving the punching hole leftward.

[Finisher]/[Post Inserter Feeder Upper Tray]/[Post Inserter Feeder Lower Tray]

Select the position subject to paper inclination adjustment.

• [Post Inserter Feeder Upper Tray]/[Post Inserter Feeder Lower Tray]: An adjustment is possible when the optional Post Inserter is installed on the machine.

[Paper Type]

Select the type of paper that is used to adjust the inclination.

[Adjust Value]

Enter the adjustment value between -5.0 mm and 5.0 mm (default: [0.0 mm]).

Increase the setting value to adjust the paper inclination. When the inclination is not corrected or paper creases after the setting value was increased, reduce the setting value.

[Paper Type]

Select the type of paper that is used to adjust the inclination.

[Adjust Value]

Enter the adjustment value between -4 and 4 (default: [0]).

Increase the setting value to adjust the paper inclination. When the inclination is not corrected or paper creases after the setting value was increased, reduce the setting value.

[Adjust Value]

Enter the adjustment value between -5.0 mm and 5.0 mm (default: [0.0 mm]).

Increase the value when moving the punching hole upward, and reduce it when moving the punching hole downward.

[Adjust Value]

Enter the adjustment value between -5.0 mm and 5.0 mm (default: [0.0 mm]).

Increase the value when moving the punching hole rightward, and reduce it when moving the punching hole leftward.

[Paper Type]

Select the paper type to adjust the fold position for.

[Adjust Value]

Enter the adjustment value between -12.8 mm and 12.7 mm (default: [0.0 mm]).

Increase the value when moving the folding position rightward, and reduce it when moving the folding position leftward.

[Paper Type]

Select the paper type to adjust the fold position for.

[Adjust Value]

Enter the adjustment value between -12.8 mm and 12.7 mm (default: [0.0 mm]).

Increase the value when moving the folding position rightward, and reduce it when moving the folding position leftward.

[Image Stabilization Only]

Select the image stabilization method (default: [Image Stabilization Only]). Use the Start key to execute image stabilization.

• [Image Stabilization Only]: Executes the standard image stabilization process.

• [Initialize + Image Stabilization]: Initializes the log information on image stabilization control and then executes image stabilization. Select this option when [Image Stabilization Only] has failed to work.

[Image Stabilization Setting]

Change the timing for executing image stabilization as well as the type of image stabilization, as required. Make selection according to the printing frequency and the color/black use ratio (default: [Standard]).

• [Standard]: Select this option when the printing frequency is low and the color printing ratio is high. Normal image stabilization is performed if a change in the absolute humidity is detected during warm-up.

• [Color Priority]: Select this option when both the printing frequency and the color printing ratio are high. Color image stabilization is performed if a change in absolute humidity is detected during warm-up.

• [Black & White Priority]: Select this option when both the printing frequency and the color printing ratio are low. Monochrome image stabilization is performed if a change in absolute humidity is detected during warm-up. Color image stabilization is to be performed before printing color documents.

[Front]/[Back]/[Thin Paper Front]/[Thin Paper Back]

Select the paper and side on which to adjust the paper separation.

[Adjust Value]

Enter the adjustment value between -10.0 mm and 10.0 mm (default: [0.0 mm]).

Increase the value if paper jams are occurring, and reduce it if the image is transferred unevenly.

[X]

If the print position of the desired color is out of line to the left or right with respect to the printing position of black, enter an adjustment value in the range between -6 dots and +6 dots (default: [0 dot]).

Increase the value when moving the printing position rightward, and reduce it when moving the printing position leftward.

[Y]

If the print position of the desired color is out of line vertically with respect to the printing position of black, enter an adjustment value in the range between -6 dots and +6 dots (default: [0 dot]).

Increase the value when moving the printing position upward, and reduce it when moving the printing position downward.

[Prior Detection Setting]

When detecting dirt on the Slit Scan Glass in advance, set this option to ON (default: ON).

• [Warning Display]: Select the type of warning messages to be displayed on the screen of this machine (default: [Type1]).
  [Type1]: Shows a warning icon in the icon display area.
  [Type2]: Shows a warning message in the message display area.
  [Type3]: Shows a warning message on the entire screen.

• [Detection level]: Select a contamination detection level (default: [Normal]).
  [Low]: Makes it harder to detect contamination.
  [Normal]: Detects contamination at an ordinary level.
  [High]: Makes it easy to detect contamination.

[Feed Cleaning Settings]

To clean the Slit Scan Glass when scanning an original in the ADF, set this option to ON (default: ON).

[Erase Operation]

Select either the option for erasing the non-image area by the optimal method automatically selected for the background density of the original or the option for erasing by the pre-specified method (default: [Specify]).

[Erase Method]

Select an erase method after selecting [Specify] for [Erase Operation].

• [Bevel]: Copies only the original by erasing the outside area around it.

• [Rectangular]: Copies the original along with the outside around it.

[Original Density]

Adjust the density of the original.

[Switch Local Weight Table]

Select the weight category to suit the distribution paper for each country (default: [Auto]).

[Weight Detection Adjustment]

To adjust a difference between measured values that is caused due to the paper feeding path, enter the adjustment value (default: [0]).

As the value is greater, the weight is detected as a thicker paper type.

[Weight Class Threshold Adjustment]

When limiting to specific paper types to increase the detection accuracy, adjust the threshold of the weight category (default: [0]).

As the value is lower, the threshold shifts to the thinner value, and it becomes easier for the paper to enter the thicker category.

[Weight Class Variation Correction]

For the paper type near the weight category border, when restricting a dispersion that occurs in the judgment results each time paper is loaded, select [Yes] (default: [No]).

[Recycled Paper Identif. Adj.]

For plain paper, adjust the threshold to identify whether the paper is recycled paper (default: [0]).

As the value is greater, it makes easier for the paper to be detected as recycled paper.

[Envelope Identific. Adj.]

For plain paper, adjust the threshold to identify whether the paper is envelope (default: [0]).

As the value is greater, it makes easier for the paper to be detected as envelope.

[Plain Paper Identific.Adj.]

For coated paper, adjust the threshold to identify whether the paper is plain paper (default: [0]).

As the value is greater, it makes easier for the paper to be detected as plain paper.

[Colored Paper Identification Adjustment]

For plain paper, adjust the threshold to identify whether the paper is colored paper (default: [0]).

As the value is greater, it makes easier for the paper to be detected as colored paper.

[Paper Addition Detection Adjustment]

When you want to always detect that paper has been added to the paper tray, select [Yes] (default: [Yes]). At the same time, adjust the setting level that determines ease of detection.