Loading Paper in Tray 1 or Tray 2

How to load paper into Tray 1 or Tray 2

The procedure for loading paper is common between Tray 1 and Tray 2. The following explains how to load paper into Tray 1.

  1. Pull out Tray 1.

    NOTICE
    • Be careful not to touch the Film.

  2. Slide the Lateral Guide to fit the size of the loaded paper.

    supplementary explanationFor Tray 1, mount the Attachment on the Lateral Guide, and slide the Lateral Guide.

  3. Load paper into the tray with the print side facing up.

    supplementary explanationWhen printing on letterhead (paper where company names, preset text, and other text or images are already printed), load it with the print side facing down.

    supplementary explanationFor details on the available paper, refer to [Paper] .

    NOTICE
    • Do not load an excessive number of sheets such that the top of the stack is higher than the Down-pointing triangle mark.

    • If paper is curled, flatten it before loading it.

  4. Close Tray 1.

    When you change the paper type or change to custom size paper, proceed to step 5 to change the setting on this machine.
    When you do not change the paper type or change to custom size paper when adding paper, you can use the current setting without making any changes.

  5. If necessary, change the paper setting of the tray on the Paper Setting screen.

    supplementary explanationThe paper type is detected automatically. Intelligent media sensor (mounted in the standard) is required to use this function. For details on Intelligent media sensor, refer to [Intelligent media sensor] .

    supplementary explanationTo disable the automatic paper type detection, set [Paper type auto detection settings] or [Auto envelope detection sett.] to OFF. For details, refer to [Paper type auto detection settings] ( [Paper type auto detection settings] ) or [Auto envelope detection sett.] ( [Auto envelope detection sett.] ).

    supplementary explanationWhen not using the automatic paper type detection, manually specify the paper type. For details, refer to [Changing the paper type] .

    supplementary explanationWhen loading custom sized paper, change the paper type setting. For details, refer to [Specifying the custom size] .

Loading postcards

Up to 200 postcards can be loaded into the Tray 1. The following example explains how to load a postcard of 4  6 (A6 Card).

  1. Pull out Tray 1.

  2. For Tray 1, mount the Attachment on the Lateral Guide.

  3. With the print side facing up, load postcards in the short edge feed direction as shown in the figure.

    NOTICE
    • When loading postcards into the Tray 1, note the following points.

    supplementary explanationWhen loading curled postcards, uncurl the postcards as shown in the figure in advance.

  4. Slide the Lateral Guide to fit the size of the loaded paper.

  5. Close Tray 1.

  6. Select [4  6] ([A6 Card]) from [Paper Size options].

Loading envelopes

Up to 70 envelopes can be loaded into the Tray 1.

Image of a long envelope

Image of a Western-style envelope

  1. Pull out Tray 1.

  2. When loading envelopes of which the length is 7-3/16 inches (182 mm) or less, mount the Attachment on the Lateral Guide.

  3. Position the flap part face down, and load envelopes as shown in the figure.

    supplementary explanationThe flap side of envelopes cannot be printed on.

    NOTICE
    • When loading envelopes into the Tray 1, note the following points.

    supplementary explanationWhen loading envelopes, remove air from them, and securely press along the flap fold line. Otherwise, it will result in an envelope wrinkle or paper jam.

    supplementary explanationDo not use envelopes that have glue or release paper on the flap or the part covered by the flap on the body. Otherwise, the machine may be damaged or a failure may occur.

  4. Slide the Lateral Guide to fit the size of the loaded paper.

  5. Close Tray 1.

  6. If necessary, change the paper setting of the tray on the Paper Setting screen.

    supplementary explanationVarious sizes of envelopes are available. Specify the correct paper size for the envelopes you have loaded. For details, refer to [Changing the paper size] .

    supplementary explanationThe paper type is detected automatically. Intelligent media sensor (mounted in the standard) is required to use this function. For details on Intelligent media sensor, refer to [Intelligent media sensor] .

    supplementary explanationTo disable the automatic paper type detection, set [Paper type auto detection settings] or [Auto envelope detection sett.] to OFF. For details, refer to [Paper type auto detection settings] ( [Paper type auto detection settings] ) or [Auto envelope detection sett.] ( [Auto envelope detection sett.] ).

    supplementary explanationWhen not using the automatic paper type detection, manually specify the paper type. For details, refer to [Changing the paper type] .

    NOTICE
    • When loading envelopes with flaps opened, also select the standard size that matches them. You do not have to measure the size of the envelope with the flap opened to set the size as a custom-sized envelope.