[Background Removal]

Copies a thin 2-sided original or an original with a colored background, at the optimum image quality level.

• [Bleed Removal]: Select this option to prevent bleeding of the back of the paper when printing a 2-sided original that is so thin that the contents of the back side would be scanned.

• [Paper Discoloration Adj.]: Select this option to scan an original with a colored background such as a map.

[Background Removal Level]

Adjusts the density of the background color for an original with a colored background. If [Auto] is selected, the density of the background color is determined automatically, and the original is copied at the optimal background density level.

[Metric Sizes]

Select this option to scan a metric-size original. Tap [Metric Sizes], and select the standard metric size respectively.

[Inch Sizes]

Select this option to scan an inch-size original. Tap [Inch Sizes], and also select a standard inch size.

[Other]

Select this option to scan a postcard (4 e 6 or A6 card) or an original other than a metric- or inch- size original. Tapping [Other] enables you to select each standard size.

[Auto]

Automatically selects paper fitting the size of the original when making a copy.

Paper Tray

Specifies the paper loaded in the paper tray when making a copy.

The displayed contents vary depending on the options installed on this machine.

[Change Settings]

If necessary, change the size and type settings of the paper loaded in the selected paper tray.

• [Paper Type]: Select the type of the paper loaded into the selected paper tray.

• [Paper Size]: Select the size of the paper loaded into the selected paper tray. This option is available when Tray 1 or Bypass Tray is selected.

Near empty icon

Indicates that very little paper remains in the paper tray.

Empty icon

Indicates that there is no paper in the paper tray.

Single Side Only

Special Paper

Plain paper+

Thick 1

Thick 1+

Thick 2

Letterhead

Colored Paper

Envelopes

Glossy Paper 1

Glossy Paper 1+

Glossy Paper 2

Postcards

Label Sheet

User Paper 1

User Paper 2

User Paper 3

User Paper 4

User Paper 5

Plain paper (Duplex 2nd Side)

Plain paper+ (Duplex 2nd Side)

Thick 1 (Duplex 2nd Side)

Thick 1+ (Duplex 2nd Side)

Thick 2 (Duplex 2nd Side)

User Paper 1 (Duplex 2nd Side)

User Paper 2 (Duplex 2nd Side)

User Paper 3 (Duplex 2nd Side)

User Paper 4 (Duplex 2nd Side)

User Paper 5 (Duplex 2nd Side)

[Auto]

Automatically makes a copy with the optimal zoom ratio to match the image of the original with the paper size. This is convenient because you do not need to specify the zoom ratio.

[Full Size]

Copies an image in the original with the same size as for the original (x1.0).

[Enlarge]

Select a preset zoom when enlarging a standard-size original onto a standard-size piece of paper for copying.

[Reduce]

Select a preset zoom when reducing a standard-size original onto a standard-size piece of paper for copying.

[Minimal]

Places an original image in the center after slightly reducing the original size when copying.

Select this option when copying the entire original image, including its edges.

[Manual]

Manually specify the zoom ratios that are different in the vertical and horizontal directions.

[Set Zoom Ratio]

Makes a copy at the registered zoom ratio.

[Original > Copy]

Select a combination of original scanning side (Simplex/Duplex) and original printing side (Simplex/Duplex).

To scan a 2-sided original, specify whether to set the original to Top Bind or Left Bind/Right Bind in [Original Binding Pos.]. To make a 2-sided copy, specify whether to set a copy to Top Bind or Left Bind/Right Bind in [Output Bind Direction].

[Combine]

Select whether to reduce and copy a two-page original on the same side of a single sheet of paper.

[Original Direction]

Specify the orientation of the loaded original.

[Original Binding Pos.]

Select the original binding position when loading a 2-sided original.

• [Auto]: The binding position of the original is specified automatically. When the long side of the original is 297 mm (11-11/16 inches) or less, the binding position is set to the long side of the paper. When the long side of the original exceeds 297 mm (11-11/16 inches), the binding position is set to the short side of the paper.

• [Top]: Select this option when the binding position is set to the top of the original.

• [Left Bind]: Select this option when the binding position is set to the left of the original.

• [Right Bind]: Select this option when the binding position is set to the right of the original.

[Output Bind Direction]

Select the binding position when printing onto both sides of sheets of paper.

• [Auto]: The binding position of a copy is specified automatically. When the long side of the original is 297 mm (11-11/16 inches) or less, the binding position is set to the long side of the paper. When the long side of the original exceeds 297 mm (11-11/16 inches), the binding position is set to the short side of the paper.

• [Top]: Select this option when setting the binding position to the top of a copy.

• [Left Bind]: Select this option when setting the binding position to the left of a copy.

• [Right Bind]: Select this option when setting the binding position to the right of a copy.

[Group/Sort]

Select the output method when making multiple copies.

• [Auto]: Automatically switches Group and Sort depending on the number of sheets of the loaded original and the number of copies. If you load originals of multiple pages and specify multiple copies, the mode is automatically switched to Sort in order to process output. If other conditions are set, output processing is carried out in Group mode.

• [Collate (By Set)]: Feeds out copies separately one by one, for example: "12345", "12345", and "12345".

• [Group]: Feeds out copies separately page by page, for example: "111", "222", "333", "444", and "555".