List of Adjustment Menu Items
Adjustment item and description | Objects/range of adjustment | ||||
|---|---|---|---|---|---|
[01 Quality Adjustment] | |||||
[01 Package Color Auto Adj.] This menu item is to be displayed on the machine mounted with Intelligent Quality Optimizer IQ-501. | |||||
Automatically adjust colors collectively. | - | ||||
[02 Package Color Manual Adj.] Manually adjust color adjustment items collectively. | - | ||||
[03 Density Balance Auto. Adj.] Perform the density balance adjustment using the scan function. | Output Chart Start | ||||
[04 Maximum Density Adjustment] | |||||
Adjust the maximum density for each of Y, M, C, and K colors. The machine will start the Gamma Automatic Adjustment after you change the maximum density. When the Gamma Automatic Adjustment is completed, proceed to the calibration with the image controller. Be sure to perform Color Density Manual Control after changing the maximum density. | Yellow: -10 (Light) to +10 (Dark) Magenta: -10 (Light) to +10 (Dark) Cyan: -10 (Light) to +10 (Dark) Black: -10 (Light) to +10 (Dark) | ||||
[05 Max. Density Auto Adj.] When Relay Unit RU-509 is mounted on the machine without Intelligent Quality Optimizer IQ-501, [Max. Density Auto Adj. (RU)] is displayed. If either optional unit is not mounted on the machine, this function is not displayed. | |||||
Automatically print and scan charts and then adjust the maximum density for each of Y, M, C, and K colors. When this adjustment is completed, proceed to the calibration with the image controller. Be sure to perform Color Density Manual Control after changing the maximum density. | ― | ||||
[06 Color Density Control] Displayed when Intelligent Quality Optimizer IQ-501 or Relay Unit RU-509 is mounted on the machine. | |||||
Make settings for controlling the color density of output paper. | ― | ||||
[07 Periodical Both Sides Adj.] This menu item is to be displayed on the machine mounted with Intelligent Quality Optimizer IQ-501. | |||||
Configure settings for the periodical both-side adjustment. | Periodical Both Sides Adj.: ON or OFF Adjustment Interval: 100 to 9,999 sheets Deviation Check: ON or OFF Specified Value: 0.5 to 10.0 mm | ||||
[02 Machine Adjustment] | |||||
[01 Printer Adjustment] | |||||
[01 Restart Timing Adjustment] Adjust the image position of lead edge in paper feed direction in the printer engine. Prerequisite: FD-Mag. Adjustment is completed. | Objects of adjustment: Restart Timing (Tray 1 to Tray 5, Bypass), Restart Timing (Back), Tray Large Plain Offset, Tray Large Thick Offset, Tray Small Plain Offset, Tray Small Thick Offset, Bypass Offset/L Plain, Bypass Offset/L Thick, Bypass Offset/S Plain, Bypass Offset/S Thick, Large Plain Offset (ADU), Large Thick Offset (ADU), Small Plain Offset (ADU), Small Thick Offset (ADU) Adjustment Range: -60 (Lower) to +60 (Higher) (1 step = 0.1 mm) | ||||
[02 Centering Adjustment] Adjust the image position in the crosswise direction of the printer engine. Prerequisite: CD-Mag. Adjustment is completed. | Objects of adjustment: Tray 1 to Tray 5, Bypass, ADU, Large Size Offset (Tray 1 to Tray 5, Bypass), Small Size Offset (Tray 1 to Tray 5, Bypass), 8.5 Adjustment Range: -40 (Front) to +40 (Back) (1 step = 0.1 mm) | ||||
[03 FD-Mag. Adjustment] Adjust the magnification in paper feed direction in the printer engine. | Objects of adjustment: Printer FD-Mag. Adjustment Range: -100 (Short) to +100 (Long) (1 step = 0.01%) Objects of adjustment: Tray 1 Offset (ADU) to Tray 5 Offset (ADU), Bypass Offset (ADU) Adjustment Range: -80 (Short) to +20 (Long) (1 step = 0.01%) | ||||
[04 CD-Mag. Adjustment] Adjust the magnification in crosswise direction in the printer engine. | Objects of adjustment: Printer CD-Mag., Tray 1 Offset (ADU) to Tray 5 Offset (ADU), Bypass Offset (ADU) Adjustment Range: -100 (Short) to +100 (Long) (1 step = 0.01%) | ||||
[02 Scan Adjustment] | |||||
[01 Restart Timing Adjustment] Adjust the scan starting position when scanning the original on the original glass. Prerequisite: FD-Mag. Adjustment is completed. | Adjustment Range: -30 (Image Slow) to +30 (Image Fast) (1 step = 0.1 mm) | ||||
[02 Centering Adjustment] Adjust the image position in the crosswise direction when scanning the original on the original glass. Prerequisite: Printer Centering Adjustment is completed. | Objects of adjustment: Orig. Glass Centering Adjustment Range: -57 (Back) to +57 (Front) (1 step = 0.1 mm) | ||||
[03 FD-Mag. Adjustment] Adjust the magnification in feed direction when scanning the original on the original glass. Prerequisite: Printer FD-Mag. Adjustment is completed. | Adjustment Range: 990 (Short) to 1010 (Long) (1 step = | ||||
[04 CD-Mag. Adjustment] Adjust the magnification in the crosswise direction when scanning the original from the original glass. Prerequisite: Printer FD-Mag. Adjustment is completed. | Adjustment Range: 990 (Short) to 1010 (Long) (1 step = | ||||
[03 Stabilization Adj. Setting] | |||||
Select Speed or Stability as job priority. | Speed or Stability - If you select Stability, the productivity may drop. - This selection is valid for jobs issued after change of this setting. | ||||
[04 Execute Adjust Operation] | |||||
Select a quality correction item and adjust the quality for your purpose. | Gamma Automatic Adj., Color Regist. Auto.Adj., Toner Refresh Mode, Belt Refresh Mode | ||||
[05 Finisher Adjustment] (Finisher FS-532) This menu item is displayed and can be set on the machine mounted with Finisher FS-532. | |||||
[01 Staple Finisher Adjustment] [01 Staple Finisher(Main) Adj.] | |||||
[01 Exit Guide Paper Width Adj.] Adjust the exit guide alignment pitch to be used by the staple finisher. Make adjustment if output paper stack on main tray is uneven in straight delivery. | Objects of adjustment: Offset for All Size, SRA3 Adjustment Range: -50 (Wide) to +50 (Narrow) (1 step = 0.1 mm) | ||||
[02 Upper Gripper Operation] Select the upper gripper operation for main tray delivery exit. | Auto, ON, OFF | ||||
[03 Output Alignment Operation] Select operation for output alignment. | Auto, ON, OFF | ||||
[04 Staple Paper Width Adj.] Adjust the board alignment width of the staples in the staple finisher. | Objects of adjustment: Offset for All Size, SRA3 Adjustment Range: -20 (Wide) to +20 (Narrow) (1 step = 0.1 mm) | ||||
[05 FD Alignment Plate Adj.] Adjust the vertical alignment fitting for staples in the staple finisher. | Objects of adjustment: Offset for All Sizes, A4 Adjustment Range: -50 (Wide) to +50 (Narrow) (1 step = 0.1 mm) | ||||
[06 Staple Position Adjustment] Adjust 2 position staple pitch and corner staple positions in the staple finisher. | Objects of adjustment: 2 Position Pitch (120 mm), 2 Position Pitch (140 mm), 2 Position Pitch (165 mm), Rear Diagonal Adjustment Range: -5 (Narrow) to +5 (Wide) (1 step = 1 mm) Adjustment Range: Rear Parallel, Front Parallel Adjustment Range: -3 (Narrow) to +3 (Wide) (1 step = 1 mm) | ||||
[07 Rewind Paddle Descent Adj.] Adjust rewind paddle descent. | Objects of adjustment: Offset for All Size, SRA3 Adjustment Range: -10 (Little) to +10 (Much) (1 step = 0.2 mm) | ||||
[08 Rewind Function Operation] Select operation for the rewind paddle. | Auto, ON, OFF | ||||
[02 Staple Finisher(Fold) Adj.] This menu item is to be displayed and become configurable on Finisher FS-532 mounted with Saddle Stitcher SD-510. | |||||
[01 Fold&Staple Paper Width Adj.] Adjust pitch of alignment plate in Saddle Stitcher SD-510 if half-folded or multi tri-folded paper show misalignment in the crosswise direction to paper feeding. | Objects of adjustment: Offset for All Size, SRA3 Adjustment Range: -50 (Narrow) to +50 (Wide) (1 step = 0.1 mm) | ||||
[02 Fold&Staple Pitch Adjustment] Adjust staple pitch in Saddle Stitcher SD-510. Make this adjustment if staple pitch is not within the allowance range. | Objects of adjustment: Offset for All Size, SRA3 Adjustment Range: -300 (Narrow) to +300 (Wide) (1 step = 0.1 mm) | ||||
[03 Fold & Staple Fold Position] Adjust half-fold position of fold & staple function in Saddle Stitcher SD-510. Make this adjustment if half-fold position is not within the specified range. | Objects of adjustment: Offset for All Size, SRA3 Adjustment Range: -50 (Extend) to +50 (Shorten) (1 step = 0.1 mm) | ||||
[04 Fold & Staple Staple Position] Adjust staple position in Saddle Stitcher SD-510. | Objects of adjustment: Offset for All Size, SRA3 Adjustment Range: -50 (Extend) to +50 (Shorten) (1 step = 0.1 mm) | ||||
[05 Half-Fold Fold Position Adj.] Adjust half-fold position of fold function in Saddle Stitcher SD-510. | Objects of adjustment: Offset for All Size, SRA3 Adjustment Range: -50 (Extend) to +50 (Shorten) (1 step = 0.1 mm) | ||||
[06 Tri-Fold Adjustment] | |||||
[01 Tri-Fold Position Adjustment] Adjust Fold 1 and Fold 2 positions for multi tri-folding in Saddle Stitcher SD-510. Make this adjustment if each fold position for tri-folding is not within the allowance range. | Objects of adjustment: 8.5 Adjustment Range: Fold 1: -50 (Extend) to +50 (Shorten) (1 step = 0.1 mm) Fold 2: -50 (Shorten) to +50 (Extend) (1 step = 0.1 mm) | ||||
[02 Double Fold Plate Adjustment] Adjust double fold plate in saddle stitcher. Make the insertion deeper if the Fold 2 misalignment is large. | Objects of adjustment: 8.5 Adjustment Range: -50 (Shallow) to +50 (Deep) (1 step = 0.1 mm) | ||||
[07 Half-Fold Strength Adj.] To suppress the opening of booklets, increase the roller pressure time. - You cannot adjust the strength to fold booklets. - Long pressure time causes less productivity. | Adjustment Range: (Additional time) 0 to +10 (1 step = 1 sec) | ||||
[03 Staple Finisher (Punch) Adj.] This menu item is to be displayed and configurable on Finisher FS-532 mounted with Punch Kit PK-522. | |||||
[01 Registration Adjustment] If the punch position is not parallel to the paper edge, control the paper curl and wrinkle by adjusting the paper loop amount of the registration roller. | Adjustment Range: -50 (Short) to +50 (Long) (1 step = 0.1 mm) | ||||
[02 Horizontal Position Adj.(FD)] Adjust the distance between the edge of the printed paper and the center of punch holes. | Objects of adjustment: Offset for All Size, A3 Adjustment Range: -50 (Far) to +50 (Close) (1 step = 0.1 mm) | ||||
[03 Vertical Position Adj.(CD)] Adjust the misalignment in center positions of paper and punch holes for each paper size. | Objects of adjustment: Offset for All Size, A3 Adjustment Range: -50 (Forward) to +50 (Backward) (1 step = 0.1 mm) | ||||
[04 Staple Finisher (PI) Adj.] This menu item is to be displayed and configurable on Finisher FS-532 mounted with PostInserter PI-502. | |||||
[01 PI Registration Adjustment] When paper fed from the upper or lower tray of PostInserter PI-502 has skew or wrinkle, or causes paper jam, adjust the paper loop of the registration roller. | Objects of adjustment: PI Upper Tray, PI Lower Tray Adjustment Range: -5 (Short) to +5 (Long) (1 step = 1.0 mm) | ||||
[05 Finisher Adjustment] (Output Tray OT-510) This menu item is displayed and can be set on the machine mounted with Output Tray OT-510. | |||||
[01 Staple Finisher Adjustment] [01 Staple Finisher(Main) Adj.] | |||||
[01 Exit Guide Paper Width Adj.] Adjust the exit guide alignment pitch to be used by the staple finisher. Make adjustment if output paper stack on main tray is uneven. | Objects of adjustment: Offset for All Size, SRA3 Adjustment Range: -50 (Wide) to +50 (Narrow) (1 step = 0.1 mm) | ||||
[02 Upper Gripper Operation] Select the upper gripper operation for main tray delivery exit. | Auto, ON, OFF | ||||
[03 Output Alignment Operation] Select operation for output alignment. | Auto, ON, OFF | ||||
[05 Finisher Adjustment] (Folding Unit FD-503) This menu item is to be displayed and allowed on the machine mounted with Folding Unit FD-503. | |||||
[02 Multi Folder Adjustment] [01 Multi Folder (Punch) Adj.] | |||||
[01 Paper Width Adjustment] Adjust the misalignment of punch hole positions. | Objects of adjustment: Offset for All Size, A3 Adjustment Range: -20 (To reduce the randomness) to +20 (To reduce the tilts) (1 step = 0.1 mm) | ||||
[02 Punch Vertical Position Adj.] | |||||
[01 2-Hole Punch] Adjust the vertical position of punch holes made by the folding unit. | Objects of adjustment: Offset for All Size, A3 Adjustment Range: -40 (To move to the center) to +40 (To move to the edge) (1 step = 0.1 mm) | ||||
[02 3-Hole Punch] Adjust the vertical position of punch holes made by the folding unit. | Adjustment Range: Offset for All Size, A3 Adjustment Range: -40 (To move to the center) to +40 (To move to the edge) (1 step = 0.1 mm) | ||||
[02 4-Hole Punch] Adjust the vertical position of punch holes made by the folding unit. | Objects of adjustment: Offset for All Size, A3 Adjustment Range: -40 (To move to the center) to +40 (To move to the edge) (1 step = 0.1 mm) | ||||
[02 Multi Folder(Fold) Adj.] | |||||
[01 Half-Fold Position Adj.] Adjust the folded position for half-fold. | Objects of adjustment: Offset for All Size, A3 Adjustment Range: -50 (To shorten the top face) to +50 (To lengthen the top face) (1 step = 0.1 mm) | ||||
[02 Z-Fold Position Adj.] Adjust the fold positions for Z-folding. Adjust Fold 1 and Fold 2 in this order. | Objects of adjustment: Offset for All Size, A3 Adjustment Range: Fold 1: -50 (To narrow) to +50 (To widen) (1 step = 0.1 mm) Fold 2: -50 (To narrow) to +50 (To widen) (1 step = 0.1 mm) | ||||
[03 Tri-Fold-in Pos. Adj.] Adjust the fold positions for tri-fold-in. Adjust Fold 1 and Fold 2 in this order. | Objects of adjustment: Offset for All Size, A3 Adjustment Range: Fold 1: -50 (To narrow) to +50 (To widen) (1 step = 0.1 mm) Fold 2: -50 (To narrow) to +50 (To widen) (1 step = 0.1 mm) | ||||
[04 Tri-Fold-out Pos. Adj.] Adjust the fold positions for tri-fold-out. Adjust Fold 1 and Fold 2 in this order. | Objects of adjustment: Offset for All Size, A3 Adjustment Range: Fold 1: -50 (To widen) to +50 (To narrow) (1 step = 0.1 mm) Fold 2: -50 (To narrow) to +50 (To widen) (1 step = 0.1 mm) | ||||
[05 Double Parallel Pos. Adj.] Adjust the fold positions for double parallel folding. Adjust Fold 1 and Fold 2 in this order. | Objects of adjustment: Offset for All Size, A3 Adjustment Range: Fold 1: -50 (To narrow) to +50 (To widen) (1 step = 0.1 mm) Fold 2: -50 (To narrow) to +50 (To widen) (1 step = 0.1 mm) | ||||
[06 Gate Position Adj.] Adjust the gate position. Adjust Fold 1, Fold 2 and Fold 3 in this order. | Objects of adjustment: Offset for All Size, A3 Adjustment Range: Fold 1: -50 (To narrow) to +50 (To widen) (1 step = 0.1 mm) Fold 2: -50 (To widen) to +50 (To narrow) (1 step = 0.1 mm) Fold 3: -50 (To narrow) to +50 (To widen) (1 step = 0.1 mm) | ||||
[05 Finisher Adjustment] (Large Capacity Stacker LS-506) This menu item is to be displayed and allowed on the machine mounted with Large Capacity Stacker LS-506. | |||||
[03 Stacker Adjustment] | |||||
[01 Paper Width Adjustment] Adjust the position of adjustment plates if output sheets show misalignment in crosswise direction on the stacker tray. | Objects of adjustment: Stacker No. 1, Stacker No. 2 Adjustment Range: -20 (To reduce the dispersion) to +20 (To reduce the distortion) (1 step = 0.1 mm) | ||||
[02 Paper Length Adjustment] Adjust the position of the stopper if output sheets show misalignment in paper feed direction on the stacker tray. | Objects of adjustment: Stacker No. 1, Stacker No. 2 Adjustment Range: -20 (To reduce the dispersion) to +20 (To reduce the distortion) (1 step = 0.1 mm) | ||||
[05 Finisher Adjustment] (Saddle Stitcher SD-506) This menu item is to be displayed and allowed on the machine mounted with Saddle Stitcher SD-506. | |||||
[04 Saddle Stitcher Adjustment] | |||||
[01 Fold Paper Width Adj.] Adjust the width of adjustment plates if half-folded or tri-folded sheets show misalignment. | Adjustment Range: Offset for All Size, SRA3 Adjustment Range: -50 (To reduce the misalignment) to +50 (To reduce the distortion) (1 step = 0.1 mm) | ||||
[02 Half-Fold Position Adj.] Adjust the folded position for half-fold. | Adjustment Range: Offset for All Size, SRA3 Adjustment Range: -50 (To shorten the top face) to +50 (To lengthen the top face) (1 step = 0.1 mm) | ||||
[03 Staple Paper Width Adj.] Adjust the width of adjustment plates of the saddle stitcher to be used in Staple mode. | Adjustment Range: Offset for All Size, SRA3 Adjustment Range: -20 (To reduce the dispersion) to +20 (To reduce the distortion) (1 step = 0.1 mm) | ||||
[04 Staple Center Position] Adjust the center position of staples determined by the saddle stitcher. Prerequisite: Staple paper width adjustment is completed. | Adjustment Range: -20 (To move closer to paper center (fold)) to +20 (To move away from paper center (fold)) (1 step = 0.1 mm) | ||||
[05 Staple Pitch Adjustment] Adjust the staple pitch determined by the saddle stitcher. | Adjustment Range: Offset for All Size, SRA3 Adjustment Range: -20 (To shorten) to +20 (To lengthen) (1 step = 1.0 mm) | ||||
[06 Trimming Adjustment] Adjust the trimming width. The trimming width should be more than 2.0 mm, otherwise the trimming operation may not performed properly. | Adjustment Range: Offset for All Size, SRA3 Adjustment Range: -400 (To narrow) to +400 (To widen) (1 step = 0.1 mm) | ||||
[07 Tri-Fold Position Adj.] Adjust the folded positions in Tri-Fold mode. Adjust Fold 1 and Fold 2 in this order. | Adjustment Range: Offset for All Size, A4 Adjustment Range: Fold 1: -100 (To widen) to +100 (To narrow) (1 step = 0.1 mm) Fold 2: -100 (To narrow) to +100 (To widen) (1 step = 0.1 mm) | ||||
[08 Trimmer Receiver Adj.] Frequent trimming operations may cause damage to the receiver, resulting in trimming failures. Move the receiver automatically or manually. *[Trimmer Receiver Adj.] is not displayed by default. To use this setting, please contact your service representative. | Objects of Adjustment: Trim Count Adjustment Range: 700 times, 500 times, 300 times Objects of adjustment: Move Pitch Adjustment Range: 1.0 mm, 1.5 mm, 2.0 mm | ||||
[05 Finisher Adjustment] (Saddle Stitcher SD-513) This menu item is to be displayed and allowed on the machine mounted with Saddle Stitcher SD-513. | |||||
[04 Saddle Stitcher Adjustment] | |||||
[01 Fold Paper Width Adj.] Adjust the width of adjustment plates if half-folded or tri-folded sheets show misalignment. | Adjustment Range: Offset for All Size, SRA3 Adjustment Range: -50 (To reduce the misalignment) to +50 (To reduce the distortion) (1 step = 0.1 mm) | ||||
[02 Fold Skew Adjustment] Adjust the skew of the folding line. | Objects of Adjustment: Single-Fold, Multi-Fold Adjustment Range: Offset for All Size, SRA3 Adjustment Range: -50 (To weaken) to +50 (To strengthen) (1 step = 0.1 mm) | ||||
[03 Half-Fold Position Adj.] Adjust the folded position for half-fold. | Adjustment Range: Offset for All Size, SRA3 Adjustment Range: -50 (To shorten the top face) to +50 (To lengthen the top face) (1 step = 0.1 mm) | ||||
[04 Tri-Fold Position Adj.] Adjust the folded positions in Tri-Fold mode. Adjust Fold 1 and Fold 2 in this order. | Adjustment Range: Offset for All Size, A4 Adjustment Range: Fold 1: -100 (To narrow) to +90 (To widen) (1 step = 0.1 mm) Fold 2: -50 (To narrow) to +50 (To widen) (1 step = 0.1 mm) | ||||
[05 Crease Position Adjustment] Adjust the crease position. | |||||
[01 Half-Fold Crease Position] Move the half-fold crease position. | Adjustment Range: Offset for All Size, SRA3 Adjustment Range: -20 (To shorten) to +20 (To lengthen) (1 step = 0.1 mm) | ||||
[02 Tri-Fold Crease Position] Move the tri-fold crease position. | Adjustment Range: Fold 1, Fold 2: Offset for All Size, A4 Adjustment Range: -20 (To shorten) to +20 (To lengthen) (1 step = 0.1 mm) | ||||
[03 PB Cover Crease Position] Move the perfect binding cover crease position. | Adjustment Range: Creace Line 1, Creace Line 2: Offset for All Size, SRA3 Adjustment Range: -20 (To shorten) to +20 (To lengthen) (1 step = 0.1 mm) | ||||
[06 Staple Paper Width Adj.] Adjust the width of adjustment plates of the saddle stitcher to be used in Staple mode. | Objects of adjustment: Offset for All Size, SRA3 Adjustment Range: -20 (To reduce the dispersion) to +20 (To reduce the distortion) (1 step = 0.1 mm) | ||||
[07 Staple Center Position] Adjust the center position of staples determined by the saddle stitcher. Prerequisite: Staple paper width adjustment is completed. | |||||
[01 2 Position Staple] Adjust the center position for 2-position staple. | Adjustment Range: -20 (To move rearward) to +20 (To move frontward) (1 step = 0.1 mm) | ||||
[02 4 Position Staple(Front 2)] Adjust the center position at two locations on the front edge for 4-position staple. | Objects of adjustment: Offset for All Size, B4 Adjustment Range: -100 (To move rearward) to +100 (To move frontward) (1 step = 0.1 mm) | ||||
[02 4 Position Staple(Rear 2)] Adjust the center position at two locations on the rear edge for 4-position staple. | Objects of adjustment: Offset for All Size, B4 Adjustment Range: -100 (To move rearward) to +100 (To move frontward) (1 step = 0.1 mm) | ||||
[08 Staple Pitch Adjustment] Adjust the staple pitch determined by the saddle stitcher. | |||||
[01 2 Position Staple] Adjust the pitch for 2-position staple. | Adjustment Range: Offset for All Size, SRA3 Adjustment Range: -20 (To shorten) to +20 (To lengthen) (1 step = 1.0 mm) | ||||
[02 4 Position Staple(Front 2)] Adjust the pitch at two locations on the front edge for 4-position staple. | Adjustment Range: Offset for All Size, B4 Adjustment Range: -10 (To shorten) to +10 (To lengthen) (1 step = 1.0 mm) | ||||
[02 4 Position Staple(Rear 2)] Adjust the pitch at two locations on the rear edge for 4-position staple. | Adjustment Range: Offset for All Size, B4 Adjustment Range: -10 (To shorten) to +10 (To lengthen) (1 step = 1.0 mm) | ||||
[09 Staple Offset Adjustment] Adjust the misalignment between the stapling positions and folding line. | Adjustment Range: -10 (To move leftward) to +10 (To move rightward) (1 step = 0.1 mm) | ||||
[10 Staple Tip Adjustment] Change the staple leg shape. | Adjustment Range: -9 (To be round) to +9 (To be flat) (1 step = 1 msec) | ||||
[11 Flattening a Fold (Strength)] Adjust the spine shape while changing the strength to form the book spine. | Adjustment Range: -20 (To decreace the force) to +20 (To increace the force) (1 step = 0.1 mm) | ||||
[12 Flattening a Fold (Freq.)] Adjust the number of roller reciprocation times to form the book spine. | Adjustment Range: -5 (To decrease) to +5 (To increase) (1 step = 1) | ||||
[13 Parallel Trimming] Adjust the levelness between the trimming line and cut edge. | Adjustment Range: Front, rear Adjustment Range: 0 (To narrow) to +30 (To widen) (1 step = 0.1 mm) | ||||
[14 Fore-edge Trimming Adj.] Adjust the trimming width. The trimming width should be more than 5 mm, otherwise the trimming operation may not performed properly. | Adjustment Range: Offset for All Size, SRA3 Adjustment Range: -400 (To narrow) to +400 (To widen) (1 step = 0.1 mm) | ||||
[15 2-Side Slitting Adjustment] Adjust the 2-side slitting. | Adjustment Range: Front, rear Adjustment Range: -10 (To narrow) to +10 (To widen) (1 step = 0.1 mm) | ||||
[16 2-Side Slit Finishing Adj.] Change the 2-side trimming speed to adjust skew and napping conditions. | Adjustment Range: 61 g/m2 or Less, 62 g/m2 or More Adjustment Range: -4 (Slow) to +4 (Fast) (1 step = 5 mm/sec.) | ||||
[17 Trimmer Receiver Adj.] Frequent trimming operations may cause damage to the receiver, resulting in trimming failures. Move the receiver automatically or manually. *[Trimmer Receiver Adj.] is not displayed by default. To use this setting, please contact your service representative. | Objects of Adjustment: Trim Count Adjustment Range: 700 times, 500 times, 300 times Objects of adjustment: Move Pitch Adjustment Range: 1.0 mm, 1.5 mm, 2.0 mm | ||||
[05 Finisher Adjustment] (Perfect Binder PB-503) This menu item is to be displayed and allowed on the machine mounted with Perfect Binder PB-503. | |||||
[05 Perfect Binder Adjustment] | |||||
[01 Sub Compile CD Width Adj.] Adjust misalignment or distortion in the crosswise direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes. | Objects of adjustment: Offset for All Size, A4 Adjustment Range: -20 (To reduce the distortion) to +20 (To reduce the misalignment) (1 step = 0.1 mm) | ||||
[02 Clamp CD Width Adjustment] Adjust misalignment or distortion in the crosswise direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes. | Objects of adjustment: Offset for All Size, A4 Adjustment Range: -20 (To reduce the distortion) to +20 (To reduce the misalignment) (1 step = 0.1 mm) | ||||
[03 Clamp FD Position Adj.] Adjust misalignment or distortion in the paper feed direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes. | Objects of adjustment: Offset for All Size, A4 Adjustment Range: -20 (To reduce the distortion) to +20 (To reduce the misalignment) (1 step = 0.1 mm) | ||||
[04 Glue Start Position] Adjust the position to start gluing on the body. The sizes referred to in this section are those of bodies corresponding to cover sizes. | Objects of adjustment: Ahead: Offset for All Size, A4 Adjustment Range: -128 (To increase) to +127 (To decrease) (1 step = 0.1 mm) | ||||
[05 Glue Finish Position] Adjust the position to finish gluing on the body. The sizes referred to in this section are those of bodies corresponding to cover sizes. | Objects of adjustment: Ahead: Offset for All Size, A4 Back: Offset for All Size, A4 Adjustment Range: -128 (To increase) to +127 (To decrease) (1 step = 0.1 mm) | ||||
[06 Cover Lead Edge Adj.] Adjust the position of the lead edge of the left cover sheet. The sizes referred to in this section are those of bodies corresponding to cover sizes. | Objects of adjustment: PB tray: Offset for All Size, A4 Except PB Tray: Offset for All Size, A4 Adjustment Range: -128 (To move closer to the body) to +127 (To move further from the body) (1 step = 0.1 mm) | ||||
[07 Cover Trimming Adjustment] Adjust the trimming width of the right cover sheet. To align the lead edges of left and right cover pages, be sure to perform Cover Lead Edge Adjustment in advance. | Objects of adjustment: Perfect Binder Tray, Except PB Tray Adjustment Range: -128 (To narrow) to +127 (To widen) (1 step = 0.1 mm) | ||||
[08 Cover Up/Down CD Width Adj.] Adjust the misalignment between the cover sheet and body. | Objects of adjustment: Perfect Binder Tray, Except PB Tray Adjustment Range: -20 (To reduce the distortion) to +20 (To reduce the misalignment) (1 step = 0.1 mm) | ||||
[09 Spine Corner Forming Pos.] Adjust the form of cover paper. | Objects of adjustment: Up/Down Forward Adj. (Front), Up/Down Rear Adj. (Rear) Adjustment Range: -128 (To convex) to +127 (To concave) (1 step = 0.1 mm) | ||||
[10 Temperature Adjustment] Glue Tank -Low: Adjust the temperature to control the tank heater. Low temperature: Increases glue viscosity. High temperature: Decreases glue viscosity. Glue Apply Roller: Adjust the temperature to control the roller heater. This also supports heating of the glue. Low temperature: Increases glue viscosity. High temperature: Decreases glue viscosity. | Objects of Adjustment: Glue Tank -Low Initial: 185°C Adjustment Range: 180°C (Down: viscosity increased) to 190°C (Up: viscosity decreased) (1 step = 1°C) Objects of adjustment: Glue Apply Roller Initial: 165°C Adjustment Range: 160°C (Down: viscosity increased) to 170°C (Up: viscosity decreased) (1 step = 1°C) | ||||
[05 Finisher Adjustment ](Finisher FS-531/Finisher FS-612) This menu item is displayed and can be set on the machine mounted with Finisher FS-531 or Finisher FS-612. | |||||
[01 Fold & Staple Stopper] Adjust the staple positions in Fold & Staple mode. (Finisher FS-612 only) | Objects of adjustment: Offset for All Size, A3 Adjustment Range: -128 (To move to the right) to +127 (To move to the left) (1 step = 0.1 mm) | ||||
[02 Half-Fold Stopper Adj.] Adjust the misalignment of the edges of printed paper. (Finisher FS-612 only) | Objects of Adjustment: Offset for All Size, A3 Adjustment Range: -128 (To lengthen the top face) to +127 (To shorten the top face) (1 step = 0.1 mm) | ||||
[03 Punch Adjustment] (Punch Kit PK-512 or Punch Kit PK-513) This option is displayed and can be set when Punch Kit PK-512 or Punch Kit PK-513 is mounted on Finisher FS-531 or Finisher FS-612. | |||||
[01 Vertical Position Adj.] Adjust the misalignment between the center of printed paper and the center of punch holes. | Objects of adjustment: Offset for All Size, A3 Adjustment Range: -50 (To move closer to front edge) to +50 (To move closer to rear edge) (1 step = 0.1 mm) | ||||
[02 Horizontal Position Adj.] Adjust the distance from the edge of the printed paper to the center of punch holes. | Objects of adjustment: PI Tray, Main Body Tray Adjustment Range: -50 (Narrow) to +50 (Wide) (1 step=0.1 mm) | ||||
[03 Registration Adjustment] Adjust the registration loop amount if punch positions are inclined. | Objects of adjustment: Main Body/Reverse, Main Body/ADU, PI 1 Tray, PI 2 Tray Adjustment Range: -20 (Increase Registration Loop) to +20 (Reduce Registration Loop) (1 step = 0.8 mm) | ||||
[04 Paper Edge Detect Sensor] Automatically adjust the sensitivity of the sensor so as to correctly detect the paper edge that is used as the reference for punch holes. | Start | ||||
[04 Tri-Fold Adjustment] Adjust the first folded positions in Tri-Fold mode. (Finisher FS-612 only) | Objects of adjustment: Offset for All Size, A4 Adjustment Range: -128 (To widen) to +127 (To narrow) (1 step=0.1 mm) | ||||
[05 2 Pos. Staple Pitch Adj.] Adjust the staple pitch determined in Fold & Staple and Staple modes. | Objects of adjustment: Fold & Staple, Staple Adjustment Range: +128 (To narrow) to +160 (To widen) (1 step = 1 mm) | ||||
[06 Post Inserter Tray Size] This menu item is displayed and can be set when Post Inserter PI-502 is mounted on Finisher FS-531 or Finisher FS-612. Adjust the tray size of post inserter. | Objects of adjustment: A4 Start | ||||
[07 Output Quantity Limit] Specify the limit on output sheets. | When Finisher FS-531 is mounted Objects of adjustment: Staple 62 to 80 g/m2, Staple 81 to 105 g/m2, Staple 106 to 135 g/m2, Staple 136 to 216 g/m2 Adjustment Range: Staple/62 to 80 g/m2: +2 to +50 (1 step = 1 sheet) When Finisher FS-612 is mounted Objects of adjustment: Staple 62 to 80 g/m2, Staple 81 to 105 g/m2, Staple 106 to 135 g/m2, Fold & Staple 62 to 80 g/m2, Fold & Staple 81 to 105 g/m2, Half-Fold 62 to 105 g/m2, Tri-Fold 62 to 80 g/m2 Adjustment Range: Staple/62 to 80 g/m2: +2 to +50 (1 step = 1 sheet) | ||||
[05 Finisher Adjustment] (Relay Unit RU-510) This menu item is to be displayed and allowed on the machine mounted with Relay Unit RU-510. | |||||
[06 Relay Stacker Adjustment] (Relay Unit RU-510) | |||||
[01 Paper Width Adjustment] Align both ends of the output sheets in order to reduce the variation and misalignment of punch holes. | Adjustment Range: -20 (To reduce the randomness) to +20 (To reduce the tilts) (1 step = 0.1 mm) | ||||
[02 Paper Length Adjustment] Adjust the stop position for the lead edge of output sheets in order to reduce the variation and misalignment of punch holes. | Adjustment Range: -50 (To reduce the dispersion) to +50 (To reduce the tilts) (1 step = 0.1 mm) | ||||
[06 ADF Adjustment] | |||||
[01 ADF Original Stop Pos. Adj.] Adjust the position to start scanning on the ADF and the image position in the crosswise direction. | Objects of adjustment: Restart Timing (Front), Restart Timing (Back) Adjustment Range: -40 (Image Fast) to +40 (Image Slow) Objects of adjustment: Centering (Front), Centering (Back) Adjustment Range: -44 (Front) to +44 (Back) | ||||
[02 ADF Orig. Stop Pos. Auto] Automatically adjust the position to start scanning on the ADF and the image position in crosswise direction. | Objects of adjustment: Restart Timing (Front), Restart Timing (Back), | ||||
[03 FD-Mag. Adjustment] Adjust the magnification in paper feed direction when scanning on the ADF. | Objects of adjustment: ADF Adjustment Range: -20 (Short) to +20 (Long) | ||||
[04 FD-Mag. Auto Adjustment] Automatically adjust the magnification in paper feed direction when scanning on the ADF. | Objects of adjustment: ADF | ||||
[05 Home Read Position Adj(Back)] Adjust the home position of the shading shaft to correct any image failure due to dirt on the shading shaft on the back side of the ADF. | Adjustment Range: -4 to +4 (1 step = 1) | ||||
[06 FD-Mag. Adjustment(Back)] Adjust the magnification in paper feed direction on the back side when scanning on the ADF. Prerequisite: Printer FD-Mag. Adjustment is completed. | Objects of adjustment: ADF Adjustment Range: (Short) -20 to +20 (Long) (1 step = 0.1 %) | ||||
[07 FD-Mag. Auto Adj.(Back)] Automatically adjust the magnification in paper feed direction on the back side when scanning on the ADF. | Objects of adjustment: ADF | ||||
[08 Main Scan Dir. Zoom(Back)] Adjust the magnification in crosswise direction on the back side when scanning on the ADF. Prerequisite: Printer CD-Mag. Adjustment is completed. | Objects of adjustment: ADF Adjustment Range: (Short) -10 to +10 (Long) (1 step = 0.1 %) | ||||
[09 Main ScanDir.Zoom Auto(Back)] Automatically adjust the magnification in crosswise direction on the back side when scanning on the ADF. | Objects of adjustment: ADF | ||||
[10 Original Tray Pre-rise Set.] Adjust the standby position of the Original feed tray on the ADF. | Original Tray Pre-rise: ON, OFF Objects of adjustment: Paper tray standby position. Adjustment Range: 1 to 7 | ||||
[07 PFU Air Assist Adjustment*] | |||||
Set the air assist setting for Paper Feeder Unit PF-707. * This setting is not displayed by default. To use this setting, please contact your service representative. | Target Tray: Tray 3, Tray 4, Tray 5 Setting Method: Auto, Manual Setting Range for Manual Adjustment: Lead Edge Air Level Setting: 1 (Weak) to 9 (Strong) Side Air Level Setting: OFF, 1 (Weak) to 9 (Strong) | ||||
