The following finishing functions are manually available with a set of paper loaded in the upper tray of the post inserter of Folding Unit FD-503.
Combination of finishing options | Finishing functions |
---|---|
Folding Unit FD-503 only | Z-Fold, Tri-Fold-in, Tri-Fold-out, Double Parallel, Gate, Half-Fold |
Folding Unit FD-503 + Finisher FS-532 | Functions available with Folding Unit FD-503 only, Corner Staple, 2 Position Staple |
Folding Unit FD-503 + Saddle Stitcher SD-506 | Functions available with Folding Unit FD-503 only, Fold & Staple |
Folding Unit FD-503 + Finisher FS-532 + Saddle Stitcher SD-510 | All functions available using the post inserter manually |
Button | Output | ||
Multi-feed detection button | Multi-feed detection - ON | Multi-feed detection - OFF | |
Staple selection button | Corner Staple | 2 Position Staple | Fold & Staple |
Punch selection button | 2-Hole Punch | 3-Hole Punch/4-Hole Punch | |
Fold selection button | Z-Fold | Tri-Fold-in | Half-Fold |
Tri-Fold-out | Double Parallel | Gate | |
When manually using the functions available with Folding Unit FD-503, Finisher FS-532, or Saddle Stitcher SD-510, you can load paper in the upper tray of the post inserter only.
Multi-feed detection is a feature that automatically stops the machine if more than one sheet is fed at a time. The post inserter is designed to operate this function. Some paper type, such as smooth surface paper, may activate this function even if a single sheet is fed, and may stop the machine as a result. Should this case occur frequently, press the Multi-feed detection button and light up the lower lamp, in order to turn the function OFF.
Place paper in the upper tray of the post inserter, then align the guides with paper.
Function | Positioning of paper |
---|---|
Corner Staple / 2 Position Staple | Position paper face up. |
Punch | Position paper face up. |
Fold | Position paper to be face up inside the fold. |
Fold & Staple | Position paper to be face up inside the booklet. |
Select the desired mode.
[1]: Staple selection button [2]: Punch selection button [3]: Fold selection button |
When selecting Corner Staple, 2 Position Staple, or Fold & Staple, press the staple selection button to turn on the lamp of desired mode.
When selecting 2- or 3-Hole Punch, press the punch selection button to turn on the lamp of desired mode.
When selecting Fold (six styles), press the fold selection button to turn on the lamp of desired mode.
Punch and Corner Staple / 2 Position Staple are compatible. To use them in combination, turn on the lamps of both functions.
Using Fold & Staple mode, the finished sets are delivered to the delivery tray. Be sure to withdraw the delivery tray of the saddle stitcher, and open the tray stand when fully withdrawing it for preparation of output.
Open the tray stand located under the tray when fully withdrawing it.
If the tray is not fully withdrawn, the machine detects that the tray is filled up even with less number of finished sets than that specified in specifications.
When using the delivery tray of the saddle stitcher, be sure to fully withdraw it. Otherwise, the sets would not be delivered to the delivery tray. Open the tray stand located under the tray when fully withdrawing it.
Press the Start/Stop button.
If multi-feeding is detected and the machine stops even if a single sheet is fed, press the multi-feed detection button to turn on the lower lamp.
To interrupt the operation, press the Start / Stop button again.
[1]: Start/Stop button |
The trays have a limit in capacity. Be careful not to exceed the limit, otherwise unexpected trouble may be caused.
The suspension button is unavailable for the job using a manual function.
[1]: Multi-feed detection button |
To fold or fold & staple booklet-styled originals manually, arrange the originals in reverse order, as shown below.
Magazine binding prints | Arrange in reverse order |