List of Setting Items (bizhub PRESS C1070P / bizhub PRESS C71hc)

[01 System Setting]

[01 Language Setting]

Select the language used in the touch panel and voice messages.

Language used in LCD: Japanese, Hangul

Taiwan, Chinese

English, French, German, Italian, Spanish

Language in voice message: English, Japanese, OFF

[02 Unit Setting]

Select the unit of measurement for numeric values to be displayed on the touch panel.

mm, Inch (Decimal Point), Inch (Fraction)

[03 Paper Tray Setting]

[01 Paper Setting]

Register or delete the paper settings. Up to 500 can be registered.

Paper Type, Profile Name, Paper Size, Weight, Colored Paper, Punch, Both Sides Adjust, Curl Adjustment, Thickness^*1, Process Adjustment^*2, Color Density
USB Memory Import, USB Memory Export

*1: Thickness is displayed when Image Controller IC-602 is mounted.

*2: Process Adjustment is unavailable by default. A service setting is required to enable it.

[02 Auto Tray Selection Setting]

Select the tray to take over the feeding when the tray currently used becomes out of paper. This function is called Auto Tray Switch (ATS). When selecting multiple trays for ATS, determine the priority of the trays.

ATS/APS Switch: Trays 1 to 5, Bypass

Tray Priority: Order of priority for selected trays

[03 Type for Auto Paper]

Specify paper conditions that enable a tray to be selected in Auto Paper (APS).

Paper conditions to be specified here are Paper Type, Weight, Punch, Tab Paper, and Colored Paper.

Paper Type: Plain, Fine, Color Specific, Coated-GL, Coated-ML, Coated-GO, Coated-MO

Weight: 62-74g/m2 / 16-19 lb Bond, 75-80g/m2 / 20-21 lb Bond, 81-91g/m2 / 22-24 lb Bond, 92-105g/m2 / 25-28 lb Bond, 106-135g/m2 / 29-36 lb Bond, 136-176g/m2 / 37-47 lb Bond, 177-216g/m2 / 48-57 lb Bond, 217-256g/m2 / 58-68 lb Bond, 257-300g/m2 / 69-81 lb Bond

Punch: Allow, Restrict

Tab Paper: Allow, Restrict

Colored Paper: Allow, Restrict

[04 Dehumidify Fan Heater]

Set the operating conditions of the dehumidifying fan heater installed in the paper feeder unit (trays 3, 4 and 5).

Dryness Preparation: ON, OFF

Fan Heater Control (Trays 3, 4 and 5): Auto, Compulsively ON, Compulsively OFF

[04 Reset Setting]

[01 Auto Reset Setting]

The screen selected as the default screen returns after a certain period of inactivity. Select the time interval to activate this function.

OFF, 60 seconds, 120 seconds, 180 seconds, 240 seconds, 300 seconds, 360 seconds, 420 seconds, 480 seconds, 540 seconds

[05 Default Screen Setting]

Select the screen to be displayed when the sub power switch is turned on or Auto Reset is activated.

MACHINE, JOB LIST/Hold Job, JOB LIST/Reserved Job

[06 Power Save Setting]

[01 Power Save Function Setting]
Select the time to activate Auto Low Power and Auto Shut OFF. Also select either Auto Low Power or Auto Shut OFF to be activated when Power Save is pressed on the control panel.

You can also select the condition of Auto Wake-up to activate the machine when a print job is received during Auto Shut OFF.

Auto Low Power: --- min., 5 min., 10 min., 15 min., 30 min., 60 min., 90 min., 120 min., 240 min.
Auto Shut OFF: --- min., 0 min., 1 min., 30 min., 60 min., 90 min., 120 min., 240 min.
Power Save Function: Auto Low Power, Auto Shut OFF
Auto Wake-up Cond.: All Jobs

[02 ErP Setting]

Automatically turn off the main power switch when the sub power switch is turned off, or when Auto Shut OFF or Auto Low Power has been active for a certain time.

Do Not Switch, 12 Hours, 24 Hours, 36 Hours, 48 Hours, 60 Hours, 72 Hours

[03 Mono Energy-save Mode]

Set whether to run Monochrome printing in energy-save mode.

ON, OFF

[07 Date/Time Setting]

Set the current date and time, the daylight-saving time, and the time difference.

Setting Time

Daylight Saving Time: OFF, ON (1 to 150 min.)

Time Zone

[08 Operation/Info. Sound Setting]

[01 Volume Setting]

Specify whether or not to enable the key operation sound or information sound and voice message, and also set the volume when they are turned on.

Operation Sound (Buzzer): ON, OFF,

1 (Small) to 8 (Big)

Info. Sound/Voice (Speaker): ON, OFF; 1 (Small) to 10 (Big)

[02 Info. Sound Item Setting]

Specify each items provided for information sound and voice message.

Repeat Number Setting

Info. Sound Repeat Number: 1 time, 2 times, 3 times

Voice Repeat Number: 1 time, 2 times, 3 times

Notice Set for Machine Stop

Paper JAM: Voice, Info. Sound, OFF

Paper Empty: Voice, Info. Sound, OFF

Paper Differ: Voice, Info. Sound, OFF

Replenish Toner: Voice, Info. Sound, OFF

Service Call: Info. Sound, OFF

Output full: Info. Sound, OFF

Other Notification Setting

Job Complete Pre-notice: Voice, OFF

Job Quantity: Over 3 minutes, Over 5 minutes, Over 10 minutes

Stop Button Acceptance: Voice, OFF

Sample Print Completion: Voice, OFF

Finisher Front Door Alert: Voice, OFF

Finisher JAM Notification: Voice, OFF

Other Info. Sound Setting

For System Starting: Info. Sound, OFF

For Sample Printing*: Info. Sound, OFF

For Print Job Receiving: Info. Sound, OFF

*This setting is displayed to function on the machine mounted with Image Controller IC-602.

[09 Key Response Time]

Select the time interval to get the response from the machine when a key is pressed on the touch panel.

Normal, 0.5 seconds, 1 second, 2 seconds, 3 seconds

[10 Service Port Device Setting]

Specify whether or not to use a service port device, and select the keyboard type if the service port device is used.

Service Port Device: ON, OFF

Keyboard Type: EN65, EN104, JP101, JP106, JP109

[11 Mouse Setting]

Select whether or not to use the Wheel Booster function and Cursor Auto Scrolling function, respectively, for when the mouse is connected.

Wheel Booster Setting: ON, OFF

When using this function, set List Scrolling Speed and Value Scrolling Speed.

Cursor Auto Scrolling Set.: ON, OFF

When using this function, set cursor speed, cancel sensitivity, and cursor prior return position, and cursor prior destination.

[02 Common Setting]

[One Shot Message Indication Time]

Select the time span to display a shot message in the message area of the touch panel.

3 seconds, 5 seconds

[Offset by Job Unit]

Specify whether or not to offset the output sheets by job. Also specify the number of jobs to be offset when selecting ON for this function.

ON, OFF (Selecting ON: Offset Job Number, Initial Value: 1)

[Continuation Print]

Specify whether or not to output multiple reserve jobs in succession without stopping the machine at a job break.

Printer ON, Printer OFF

[Stop Button Function]

Specify whether to pause or abort a job when Stop is pressed on the control panel.

Job Temp. Stop, Job Stop

[Back Side Magnification Adjustment]

Select whether or not to activate the back side magnification adjustment mode.

ON, OFF

[Fusing Stability]

Select what to prioritize when fusing.

Best Quality, Better Quality, Speed

[Prior Paper Type]

Specify the temperature setting of the fusing section on standby. It can shorten the waiting time before printing by selecting a frequently used paper.

Others, Plain

[Dash Length (Page Stamp)]

Select the length of the dash to be used in a style of [Page No.] in [Stamp].

This setting is displayed to function on the machine mounted with Image Controller IC-602.

Long, Short

[Center Crop Mark Trim Margin]

Specify the space between the center crop mark and image area (center crop mark trim margin).

0.0 mm to 20.0 mm (default: 1.0)

[Schedule Cross Axis Unit (Default)]

Select the unit of horizontal axis on the [Schedule] screen.

This setting is displayed to function on the machine mounted with Image Controller IC-602.

Timetable, Time Frame (m), Sheet Volume

[Hold Job Status after Output (Default)]

Select the default value to delete or save the data of hold job after outputting.

Delete, Save

[Destination for HDD Recall (Default)]

Select the default destination for the job data recalled from the HDD.

Print, Hold, Print&Hold,

[Offset Output Mode]

Specify how to offset the output sets.

Change Out Pos., Partition Paper (Tray 1 to Tray 5, Bypass, PI 1, PI 2), Stop Print

[Needless Tab Paper Exit]

Specify whether or not to automatically discharge the oddments of tabbed sheets loaded in a tray as a set.

ON, OFF

[Banner]

This setting is displayed to function on the machine mounted with Banner Tray Unit MK-740.

ON, OFF

[Remaining Memory (Measurement Unit)]

Select the unit of displaying the remaining memory.

%, GB

 [Remaining Memory (Warning)]

Select the percentage at which to give warning when the remaining memory is low.

 5% or Less2, 10% or Less

[03 Printer Setting]

[01 Outline Process]

Select the Outline Process for printing.

Text Thinning: Weak+, Weak, Normal, Strong, Strong+

Halftone Text Enhancement: Weak+, Normal, Strong+

FD Lead Edge Density Adjustment: 0 to +5

FD Rear Edge Density Adjustment: -5 to 0

[02 Select Prior Output Tray]

Select the output tray for the jobs for which the output tray is specified as "Auto." This menu item is to be displayed and allowed on the machine mounted with Finisher FS-531/FS-532/FS-612.

Main Tray, Sub Tray

[04 Change Password]

Change the user password previously registered with user authentication.

Entry of a new password

[01 System Setting]

[01 Power Save Setting]

[01 Power Save Function Setting]
Select the time to activate Auto Low Power and Auto Shut OFF. Also select either Auto Low Power or Auto Shut OFF to be activated when Power Save is pressed on the control panel.

You can also select the condition of Auto Wake-up to activate the machine when a print job is received during Auto Shut OFF.

Auto Low Power: --- min., 5 min., 10 min., 15 min., 30 min., 60 min., 90 min., 120 min., 240 min.

Auto Shut OFF: --- min., 0 min., 1 min., 30 min., 60 min., 90 min., 120 min., 240 min.

Power Save Function: Auto Low Power, Auto Shut OFF

Auto Wake-up Cond.: All Jobs

[02 ErP Setting]

Automatically turn off the main power switch when the sub power switch is turned off, or when Auto Shut OFF or Auto Low Power has been active for a certain time.

Do Not Switch, 12 Hours, 24 Hours, 36 Hours, 48 Hours, 60 Hours, 72 Hours

[03 Mono Energy-save Mode]

Set whether to run Monochrome printing in energy-save mode.

ON, OFF

[02 Date/Time Setting]

Set the current date and time, the daylight-saving time, and the time difference.

Setting Time

Daylight Saving Time: OFF, ON (1 to 150 min.)

Time Zone

[03 Weekly Timer Setting]

[01 Weekly Timer On/Off Setting]

Specify whether or not to use the Weekly Timer function.

Weekly Timer ON, Weekly Timer OFF

[02 Time Setting]

Set the ON/OFF times in hours and minutes.

-

[03 Date Setting]

Set the ON/OFF condition of the machine for a given day of a given month.

-

[04 Select Time for Power Save]

Set the machine to turn off and then on during the lunch break.

ON, OFF

[05 Password Non-Business Hours]

Set a password to use the machine by turning on the power temporarily while the machine is in off condition due to the Weekly Timer function.

0000 (4 digits)

[04 Restrict User Access]

[01 Restriction for Sample Print]

Specify whether or not to allow the use of sample print function.

This menu item is displayed to function on the machine mounted with Image Controller IC-602.

Sample Print: Allow, Restrict

[05 Expert Adjustment]

[01 Printer Adjustment]

[01 Restart Timing Adjustment]

Adjust the image position of lead edge in paper feed direction in the printer engine.

Prerequisite:

FD-Mag. Adjustment is completed.

Objects of adjustment:

Restart Timing (Tray 1 to Tray 5, Bypass), Restart Timing (Back), Tray Large Plain Offset, Tray Large Thick Offset, Tray Small Plain Offset, Tray Small Thick Offset, Bypass Offset/L Plain, Bypass Offset/L Thick, Bypass Offset/S Plain, Bypass Offset/S Thick, Large Plain Offset (ADU), Large Thick Offset (ADU), Small Plain Offset (ADU), Small Thick Offset (ADU)

Adjustment Range:

-60 (Lower) to +60 (Higher)

(1 step=0.1 mm)

[02 Centering Adjustment]

Adjust the image position in the crosswise direction of the printer engine.

Prerequisite:

CD-Mag. Adjustment is completed.

Objects of adjustment:

Tray 1 to Tray 5, Bypass, ADU, Large Size Offset (Tray 1 to Tray 5, Bypass), Small Size Offset (Tray 1 to Tray 5, Bypass), 8.5 5.5 Offset (Tray 1 to Tray 2, Bypass), Large Plain Offset (ADU), Large Thick Offset (ADU), Small Plain Offset (ADU), Small Thick Offset (ADU), 8.5 5.5 Plain Offset (ADU), 8.5 5.5 Thick Offset (ADU)

Adjustment Range:

-40 (Front) to +40 (Back)

(1 step=0.1 mm)

[03 FD-Mag. Adjustment]

Adjust the magnification in paper feed direction in the printer engine.

Objects of adjustment:

Printer FD-Mag.

Adjustment Range:

-100 (Short) to +100 (Long)

(1 step = 0.01%)

Objects of adjustment:

Tray 1 Offset (ADU) to Tray 5 Offset (ADU), Bypass Offset (ADU)

Adjustment Range:

-80 (Short) to +20 (Long)

(1 step = 0.01%)

[04 CD-Mag. Adjustment]

Adjust the magnification in crosswise direction in the printer engine.

Objects of adjustment:

Printer CD-Mag., Tray 1 Offset (ADU) to Tray 5 Offset (ADU), Bypass Offset (ADU)

Adjustment Range:

-100 (Short) to +100 (Long)

(1 step = 0.01%)

[05 Registration Loop Adj.]

Adjust the paper loop amount in registration roller section.

Objects of adjustment:

Tray 1 Large Size to Tray 5 Large Size, Tray 1 Small Size to Tray 5 Small Size, Bypass Large Size, Bypass Small Size, ADU Large Size, ADU Small Size, ADU Plain/W Under 150 mm, ADU Thick/W Under 150 mm, Thick

Adjustment Range:

-99 (Short) to +99 (Long)

(1 step=0.1 mm)

[06 Pre-registration Adj.]

Adjust the paper loop amount in pre-registration roller section of the trays.

Objects of adjustment:

Tray 1 to Tray 5, ADU Large Size, ADU Small Size, ADU Width 150 mm or Less

Adjustment Range:

-99 (Short) to +99 (Long)

(1 step=0.1 mm)

[07 Print Job JAM Setting]

Set whether or not to stop the machine as a paper jam when a mis-centering is detected. And set whether or not to display a message indicating the cause of the JAM when the machine stops as JAM.

Mis-centering JAM Setting: Detect, Not Detect

JAM Identification Display: Display, Not Display

[02 Finisher Adjustment] (Finisher FS-532)

This menu item is to be displayed and allowed on the machine mounted with Finisher FS-532.

[01 Staple Finisher Adjustment]

[01 Staple Finisher(Main) Adj.]

[01 Staple Position Adjustment]

Adjust 2 position staple pitch and corner staple positions in staple finisher.

Objects of adjustment:

2 Position Pitch (120 mm), 2 Position Pitch (140 mm), 2 Position Pitch (165 mm), Rear Diagonal

Adjustment Range:

-5 (Narrow) to +5 (Wide)

(1 step = 1.0 mm)

Objects of adjustment:

Rear Parallel, Front Parallel

Adjustment Range:

-3 (Narrow) to +3 (Wide)

(1 step = 1.0 mm)

[02 Staple Paper Width Adj.]

Adjust the board alignment width of the staples in the staple finisher.

Objects of adjustment:

Offset for All Size, SRA3 , A3 , SRA4 , A4 /, A5 , B4 , B5 , 8K , 16K , 12 18 , 11 17 , 9 11 , 8.5 11 /, 8.5 14 , 8 13 , 8.12 13.2 , 8.5 13 , 8.25 13 , 13 19 , SRA4 , 16K , Custom (380 to 488 mm), Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-20 (Wide) to +20 (Narrow)

(1 step=0.1 mm)

[03 FD Alignment Plate Adj.]

Adjust the vertical alignment fitting for staples in the staple finisher.

Objects of adjustment:

Offset for All Sizes, A4 , B5 , A5 , 8.5 11 , 16K , 9 11 , Custom (148 to 230 mm)

Adjustment Range:

-50 (Wide) to +50 (Narrow)

(1 step=0.1 mm)

[04 Exit Guide Paper Width Adj.]

Adjust the exit guide alignment pitch to be used by the staple finisher.

Make adjustment if output paper stack on main tray is uneven in straight delivery.

Objects of adjustment:

Offset for All Size, SRA3 , A3 , SRA4 , A4 /, A5 , B4 , B5 , 8K , 16K , 12 18 , 11 17 , 9 11 , 8.5 11 /, 8.5 14 , 8 13 , 8.12 13.2 , 8.5 13 , 8.25 13 , 13 19 , B5 , A6 , SRA4 , B6 , 16K , Custom (380 to 488 mm), Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-50 (Wide) to +50 (Narrow)

(1 step=0.1 mm)

[05 Rewind Paddle Descent Adj.]

Adjust rewind paddle descent.

Objects of adjustment:

Offset for All Size, SRA3 , A3 , SRA4 , A4 /, A5, B4 , B5 , 8K , 16K , 12 18 , 11 17 , 9 11 , 8.5 11 /, 8.5 14 , 8 13 , 8.12 13.2 , 8.5 13 , 8.25 13 , 13 19 , SRA4 , 16K , Custom (380 to 488 mm), Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-10 (Little) to +10 (Much)

(1 step = 0.2 mm)

[06 Rewind Function Operation]

Select operation for the rewind paddle.

Auto, ON, OFF

[07 Upper Gripper Operation]

Select the upper gripper operation for main tray outlet.

Auto, ON, OFF

[08 Output Alignment Operation]

Select operation for output alignment.

Auto, ON, OFF

[02 Staple Finisher(Fold) Adj.]

This menu item is to be displayed and become configurable on Finisher FS-532 mounted with Saddle Stitcher SD-510.

[01 Fold&Staple Pitch Adjustment]

Adjust staple pitch in Saddle Stitcher SD-510. Make this adjustment if staple pitch is not within the allowance range.

Objects of adjustment:

Offset for All Size, SRA3 , 12 18 , A3 , 11 17 , 8K , B4 , SRA4 , 8.5 14 , 8.5 11 , B5 , A4 , 16K , 8.12 13.2 , 8.5 13 , 8.25 13 , 8 13 , 13 19 , Custom (380 to 488 mm), Custom (240 to 379 mm)

Adjustment Range:

-300 (Narrow) to +300 (Wide)

(1 step=0.1 mm)

[02 Fold&Staple Paper Width Adj.]

Adjust pitch of alignment plate in Saddle Stitcher SD-510 if half-folded or multi tri-folded sheets show misalignment.

Objects of adjustment:

Offset for All Size, SRA3 , 12 18 , A3 , 11 17 , 8K , B4 , SRA4 , 8.5 14 , 8.5 11 , B5 , A4 , 16K , 8.12 13.2 , 8.5 13 , 8.25 13 , 8 13 , 13 19 , Custom (380 to 488 mm), Custom (240 to 379 mm)

Adjustment Range:

-50 (Narrow) to +50 (Wide)

(1 step=0.1 mm)

[03 Fold & Staple Staple Position]

Adjust staple position in Saddle Stitcher SD-510.

Objects of adjustment:

Offset for All Size, SRA3 , 12 18 , A3 , 11 17 , 8K , B4 , SRA4 , 8.5 14 , 8.5 11 , B5 , A4 , 16K , 8.12 13.2 , 8.5 13 , 8.25 13 , 8 13 , 13 19 , Custom (380 to 488 mm), Custom (240 to 379 mm)

Adjustment Range:

Top face of output paper: -50 (Extend) to +50 (Shorten)

(1 step=0.1 mm)

[04 Fold & Staple Fold Position]

Adjust half-fold position of fold & staple function in Saddle Stitcher SD-510. Make this adjustment if half-fold position is not within the specified range.

Objects of adjustment:

Offset for All Size, SRA3 , 12 18 , A3 , 11 17 , 8K , B4 , SRA4 , 8.5 14 , 8.5 11 , B5 , A4 , 16K , 8.12 13.2 , 8.5 13 , 8.25 13 , 8 13 , 13 19 , Custom (380 to 488 mm), Custom (240 to 379 mm)

Adjustment Range:

Top face of output paper: -50 (Extend) to +50 (Shorten)

(1 step=0.1 mm)

[05 Half-Fold Fold Position Adj.]

Adjust half-fold position of fold function in Saddle Stitcher SD-510.

Objects of adjustment:

Offset for All Size, SRA3 , 12 18 , A3 , 11 17 , 8K , B4 , SRA4 , 8.5 14 , 8.5 11 , B5 , A4 , 16K , 8.12 13.2 , 8.5 13 , 8.25 13 , 8 13 , 13 19 , Custom (380 to 488 mm), Custom (240 to 379 mm)

Adjustment Range:

Top face of output paper: -50 (Extend) to +50 (Shorten)

(1 step=0.1 mm)

[06 Tri-Fold Adjustment]

[01 Tri-Fold Position Adjustment]

Adjust Fold 1 and Fold 2 positions for multi tri-folding in Saddle Stitcher SD-510.

Make this adjustment if each fold position for tri-folding is not within the allowance range.

Objects of adjustment:

8.5 11 , A4 , 16K

Adjustment Range:

Fold 1: -50 (Extend) to +50 (Shorten)

(1 step=0.1 mm)

Fold 2: -50 (Shorten) to +50 (Extend)

(1 step=0.1 mm)

[02 Double Fold Plate Adjustment]

Adjust double fold plate in saddle stitcher.

Deepen in case of wide shift in bunch of the Fold 2.

Objects of adjustment:

8.5 11 , A4 , 16K

Adjustment Range:

-50 (Shallow) to +50 (Deep)

(1 step=0.1 mm)

[07 Half-Fold Strength Adj.]

To adjust the opening of booklets, increase the roller pressure time.

* You cannot adjust the strength to fold booklets.

* Long pressure time causes reduced productivity.

Adjustment Range:

(Additional time) 0 to +10

(1 step = 1 sec)

[03 Staple Finisher (Punch) Adj.]

This menu item is to be displayed and configurable on Finisher FS-532 mounted with Punch Kit PK-522.

[01 Vertical Position Adj.(CD)]

Adjust the misalignment in center positions of paper and punch holes for each paper size.

Objects of adjustment:

Offset for All Size, A3 , A4 , A4 , SRA4 , A5 , B4 , B5 , 8K , 16K , 16K , 8.5 14 , 8.5 11 , 8.5 11 , 12 18 , 8.12 13.2 , 11 17 , 8.5 13 , 8.25 13 , 8 13 , 5.5 8.5 , 9 11 , B5

Adjustment Range:

-50 (Forward) to +50 (Backward)

(1 step=0.1 mm)

[02 Horizontal Position Adj.(FD)]

Adjust the distance between the edge of the printed paper and the center of punch holes.

Objects of adjustment:

Offset for All Size, A3 , A4 , A4 , SRA4 , A5 , B4 , B5 , 8K , 16K , 16K , 8.5 14 , 8.5 11 , 8.5 11 , 12 18 , 8.12 13.2 , 11 17 , 8.5 13 , 8.25 13 , 8 13 , 5.5 8.5 , 9 11 , B5

Adjustment Range:

-50 (Far) to +50 (Close)

(1 step=0.1 mm)

[03 Registration Adjustment]

If the punch position is not parallel to the paper edge, control the paper curl and wrinkle by adjusting the paper loop amount of the registration roller.

Adjustment Range:

-50 (Short) to +50 (Long)

(1 step=0.1 mm)

[04 Staple Finisher (PI) Adj.]

This menu item is to be displayed and configurable on Finisher FS-532 mounted with PostInserter PI-502.

[01 PI Registration Adjustment]

When paper fed from the upper or lower tray of PostInserter PI-502 has skew or wrinkle, or causes paper jam, adjust the paper loop of the registration roller.

Objects of adjustment:

PI Upper Tray, PI Lower Tray

Adjustment Range:

-5 (Short) to +5 (Long)

(1 step = 1.0 mm)

[02 Finisher Adjustment] (Folding Unit FD-503)

This menu item is to be displayed and allowed on the machine mounted with Folding Unit FD-503.

[02 Multi Folder Adjustment]

[01 Multi Folder (Punch) Adj.]

[01 Paper Width Adjustment]

Adjust the misalignment of punch hole positions.

Objects of adjustment:

Offset for All Size, A3 , B4 , SRA4 , A4 /, B5 /, A5 /, 12 18 , 11 17 , 8.5 14 , 8.5 11 /, 8.125 13.25 , 8.5 13 , 8.25 13 , 8 13 , 8K , 16K /, 9 11

Adjustment Range:

-20 (To reduce the randomness) to +20 (To reduce the tilts)

(1 step=0.1 mm)

[02 Punch Vertical Position Adj.]

[01 2-Hole Punch]

Adjust the vertical position of punch holes made by the folding unit.

Objects of adjustment:

Offset for All Size, A3 , B4 , SRA4 , A4 /, B5 /, A5 /, 12 18 , 11 17 , 8.5 14 , 8.5 11 /, 8.125 13.25 , 8.5 13 , 8.25 13 , 8 13 , 8K , 16K /, 9 11

Adjustment Range:

-40 (To move to the center) to +40 (To move to the edge)

(1 step=0.1 mm)

[02 3-Hole Punch]

Adjust the vertical position of punch holes made by the folding unit.

Objects of adjustment:

Offset for All Size, A3 , B4 , SRA4 , A4 , B5 , 12 18 , 11 17 , 8.5 11 , 8K , 16K , 9 11

Adjustment Range:

-40 (To move to the center) to +40 (To move to the edge)

(1 step=0.1 mm)

[02 4-Hole Punch]

Adjust the vertical position of punch holes made by the folding unit.

Objects of adjustment:

Offset for All Size, A3 , B4 , SRA4 , A4 , B5 , 12 18 , 11 17 , 8.5 11 , 8K , 16K , 9 11

Adjustment Range:

-40 (To move to the center) to +40 (To move to the edge)

(1 step=0.1 mm)

[02 Multi Folder(Fold) Adj.]

[01 Half-Fold Position Adj.]

Adjust the folded position for half-fold.

Objects of adjustment:

Offset for All Size, A3 , B4 , SRA4 , A4 , 12 18 , 11 17 , 8.5 14 , 8.5 11 , 8K , Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range:

-50 (To shorten the top face) to +50 (To lengthen the top face)

(1 step=0.1 mm)

[02 Tri-Fold-in Pos. Adj.]

Adjust the fold positions for tri-fold-in.

Start with Fold 1, and then set Fold 2.

Objects of adjustment:

Offset for All Size, A3 , B4 , SRA4 , A4 , 12 18 , 11 17 , 8.5 14 , 8.5 11 , 8K , Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range:

Fold 1: -50 (To narrow) to +50 (To widen)

(1 step=0.1 mm)

Fold 2: -50 (To narrow) to +50 (To widen)

(1 step=0.1 mm)

[03 Tri-Fold-out Pos. Adj.]

Adjust the fold positions for tri-fold-out.

Start with Fold 1, and then set Fold 2.

Objects of adjustment:

Offset for All Size, A3 , B4 , SRA4 , A4 , 12 18 , 11 17 , 8.5 14 , 8.5 11 , 8K , Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range:

Fold 1: -50 (To widen) to +50 (To narrow)

(1 step=0.1 mm)

Fold 2: -50 (To narrow) to +50 (To widen)

(1 step=0.1 mm)

[04 Double Parallel Pos. Adj.]

Adjust the fold positions for double parallel folding.

Start with Fold 1, and then set Fold 2.

Objects of adjustment:

Offset for All Size, A3 , B4 , SRA4 , A4 , 12 18 , 11 17 , 8.5 14 , 8.5 11 , 8K , Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range:

Fold 1: -50 (To narrow) to +50 (To widen)

(1 step=0.1 mm)

Fold 2: -50 (To narrow) to +50 (To widen)

(1 step=0.1 mm)

[05 Z-Fold Position Adj.]

Adjust the fold positions for Z-folding.

Start with Fold 1, and then set Fold 2.

Objects of adjustment:

Offset for All Size, A3 , B4 , SRA4 , A4 , 12 18 , 11 17 , 8.5 14 , 8.5 11 , 8K , Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range:

Fold 1: -50 (To narrow) to +50 (To widen)

(1 step=0.1 mm)

Fold 2: -50 (To narrow) to +50 (To widen)

(1 step=0.1 mm)

[06 Gate Position Adj.]

Adjust the fold position for gate folding.

Start with Fold 1, and then set Fold 2 and Fold 3.

Objects of adjustment:

Offset for All Size, A3 , B4 , SRA4 , A4 , 12 18 , 11 17 , 8.5 14 , 8.5 11 , 8K , Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range:

Fold 1: -50 (To narrow) to +50 (To widen)

(1 step=0.1 mm)

Fold 2: -50 (To widen) to +50 (To narrow)

(1 step=0.1 mm)

Fold 3: -50 (To narrow) to +50 (To widen)

(1 step=0.1 mm)

[02 Finisher Adjustment](Large Capacity Stacker LS-505/Large Capacity Stacker LS-506)

This menu item is displayed and allowed when Large Capacity Stacker LS-505 or Large Capacity Stacker LS-506 is mounted.

[03 Stacker Adjustment]

[01 Paper Width Adjustment]

Adjust the position of adjustment plates if output sheets show misalignment in crosswise direction on the stacker tray.

Objects of adjustment:

Stacker No. 1, Stacker No. 2

Adjustment Range:

-20 (To reduce the dispersion) to +20 (To reduce the distortion)

(1 step=0.1 mm)

[02 Paper Length Adjustment]

Adjust the position of the stopper if output sheets show misalignment in paper feed direction on the stacker tray.

Objects of adjustment:

Stacker No. 1, Stacker No. 2

Adjustment Range:

-20 (To reduce the dispersion) to +20 (To reduce the distortion)

(1 step=0.1 mm)

[02 Finisher Adjustment] (Saddle Stitcher SD-506)

This menu item is to be displayed and allowed on the machine mounted with Saddle Stitcher SD-506.

[04 Saddle Stitcher Pos. Adj.]

[01 Staple Center Position]

Adjust the center position of staples determined by the saddle stitcher.

Prerequisite: Staple paper width adjustment is completed.

Adjustment Range:

-20 (To move closer to paper center) to +20 (To move away from paper center)

(1 step=0.1 mm)

[02 Staple Paper Width Adj.]

Adjust the width of adjustment plates of the saddle stitcher to be used in Staple mode.

Objects of adjustment:

Offset for All Size, SRA3 , A3 , B4 , SRA4 , A4 , B5 , 12 18 , 11 17 , 8.5 14 , 8.5 11 , 8.125 13.25 , 8.5 13 , 8.25 13 , 8 13 , 8K , 16K , Custom (380 to 463 mm), Custom (257 to 379 mm)

Adjustment Range: -20 (To reduce the dispersion) to +20 (To reduce the distortion)

(1 step=0.1 mm)

[03 Staple Pitch Adjustment]

Adjust the staple pitch determined by the saddle stitcher.

Objects of adjustment:

Offset for All Size, SRA3 , A3 , B4 , SRA4 , A4 , B5 , 12 18 , 11 17 , 8.5 14 , 8.5 11 , 8.125 13.25 , 8.5 13 , 8.25 13 , 8 13 , 8K , 16K , Custom (380 to 463 mm), Custom (257 to 379 mm)

Adjustment Range:

-20 (To shorten) to +20 (To lengthen)

(1 step=0.1 mm)

[04 Half-Fold Position Adj.]

Adjust the fold position determined by the half-folder.

Objects of adjustment:

Offset for All Size, SRA3 , A3 , B4 , SRA4 , A4 , B5 , 12 18 , 11 17 , 8.5 14 , 8.5 11 , 8.125 13.25 , 8.5 13 , 8.25 13 , 8 13 , 8K , 16K , Custom (380 to 463 mm), Custom (257 to 379 mm)

Adjustment Range:

-50 (To shorten the top face) to +50 (To lengthen the top face)

(1 step=0.1 mm)

[05 Tri-Fold Position Adj.]

Adjust the folded positions in Tri-Fold mode.

Start with Fold 1, and then set Fold 2.

Objects of adjustment:

Offset for All Size, A4 , 8.5 11

Adjustment Range:

Fold 1: -100 (To widen) to +100 (To narrow)

(1 step=0.1 mm)

Fold 2: -100 (To narrow) to +100 (To widen)

(1 step=0.1 mm)

[06 Fold Paper Width Adj.]

Adjust the width of adjustment plates if half-folded or tri-folded sheets show misalignment.

Objects of adjustment:

Offset for All Size, SRA3 , A3 , B4 , SRA4 , A4 , B5 , 12 18 , 11 17 , 8.5 14 , 8.5 11 , 8.125 13.25 , 8.5 13 , 8.25 13 , 8 13 , 8K , 16K , PI, Custom (380 to 463 mm), Custom (257 to 379 mm)

Adjustment Range:

-50 (To reduce the misalignment) to +50 (To reduce the distortion)

(1 step=0.1 mm)

[07 Trimming Adjustment]

Adjust the trimming width.
The trim width should be more than 2.0 mm, otherwise the trimming operation may not be performed properly.

Objects of adjustment:

Offset for All Size, SRA3 , A3 , B4 , SRA4 , A4 , B5 , 12 18 , 11 17 , 8.5 14 , 8.5 11 , 8.125 13.25 , 8.5 13 , 8.25 13 , 8 13 , 8K , 16K , Custom (380 to 463 mm), Custom (257 to 379 mm)

Adjustment Range:

-400 (To narrow) to +400 (To widen)

(1 step=0.1 mm)

[08 Trimmer Receiver Adj.]

Frequent trimming operations may cause damage to the receiver, resulting in trimming failures. Move the receiver automatically or manually.

*[Trimmer Receiver Adj.] is not displayed by default. To use this setting, please contact your service representative.

Objects of Adjustment: Trim Count

Adjustment Range: 700 times, 500 times, 300times

Objects of Adjustment: Move Pitch

Adjustment Range: 1.0 mm, 1.5 mm, 2.0 mm

[02 Finisher Adjustment] (Perfect Binder PB-503)

This menu item is to be displayed and allowed on the machine mounted with Perfect Binder PB-503.

[05 Perfect Binder Adjustment]

[01 Cover Trimming Adjustment]

Adjust the trimming width of the right cover sheet. To align the lead edges of left and right cover pages, be sure to perform Cover Lead Edge Adjustment in advance.

Objects of adjustment:

Perfect Binder Tray, Except PB Tray

Adjustment Range:

-128 (To narrow) to +127 (To widen)

(1 step=0.1 mm)

[02 Cover Lead Edge Adj.]

Adjust the position of the lead edge of the left cover sheet. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

PB Tray: Offset for All Size, A4 , B5 , A5 , 8.5 11 , 16K , A5 , 5.5 8.5 , Custom (220 to 379 mm), Custom (148 to 219 mm)

Except PB Tray: Offset for All Size, A4 , B5 , A5 , 8.5 11 , 16K , A5 , 5.5 8.5 , Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-128 (To move closer to the body) to +127 (To move further from the body)

(1 step=0.1 mm)

[03 Spine Corner Forming Pos.]

Adjust the spine corners formed in cover sheets.

Objects of adjustment:

Up/Down Forward Adj., Up/Down Rear Adj.

Adjustment Range:

-128 (To convex) to +127 (To concave)

(1 step=0.1 mm)

[04 Glue Start Position]

Adjust the position to start gluing on the body. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Ahead: Offset for All Size, A4 , B5 , A5 /, 8.5 11 , 5.5 8.5 , 16K , Custom (220 to 379 mm), Custom (148 to 219 mm)

Back: Offset for All Size, A4 , B5 , A5 /, 8.5 11 , 5.5 8.5 , 16K , Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-128 (To increase) to +127 (To decrease)

(1 step=0.1 mm)

[05 Glue Finish Position]

Adjust the position to finish gluing on the body. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Ahead: Offset for All Size, A4 , B5 , A5 /, 8.5 11 , 5.5 8.5 , 16K , Custom (220 to 379 mm), Custom (148 to 219 mm)

Back: Offset for All Size, A4 , B5 , A5 /, 8.5 11 , 5.5 8.5 , 16K , Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-128 (To decrease) to +127 (To increase)

(1 step=0.1 mm)

[06 Temperature Adjustment]

Glue Tank -Low:

Adjust the temperature to control the tank heater.

Low temperature: increases glue viscosity, High temperature: decreases glue viscosity

Glue Apply Roller:

Adjust the temperature to control the roller heater. This also supports heating of the glue.

Low temperature: increases glue viscosity, High temperature: decreases glue viscosity

Objects of Adjustment: Glue Tank -Low

Initial: 185°C

Adjustment Range:

180°C (Down: viscosity increased) to 190°C (Up: viscosity decreased)

(1 step = 1°C)

Objects of Adjustment: Glue Apply Roller

Initial: 165°C

Adjustment Range:

160°C (Down: viscosity increased) to 170°C (Up: viscosity decreased)

(1 step = 1°C)

[07 Sub Compile CD Width Adj.]

Adjust the upside if output sheets cannot be aligned in sub compile section. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Offset for All Size, A4 , B5 , A5 /, 8.5 11 , 5.5 8.5 , 16K , Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-20 (To reduce the distortion) to +20 (To reduce the dispersion)

(1 step=0.1 mm)

[08 Clamp CD Width Adjustment]

Adjust the upside if output sheets cannot be aligned in clamp section. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Offset for All Size, A4 , B5 , A5 /, 8.5 11 , 5.5 8.5 , 16K , Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-20 (To reduce the distortion) to +20 (To reduce the dispersion)

(1 step=0.1 mm)

[09 Cover Up/Down CD Width Adj.]

Adjust the misalignment between the cover sheet and body.

Objects of adjustment:

Perfect Binder Tray, Except PB Tray

Adjustment Range:

-20 (To reduce the distortion) to +20 (To reduce the dispersion)

(1 step=0.1 mm)

[10 Clamp FD Position Adj.]

Adjust the width if there is misalignment in the body. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Offset for All Size, A4 , B5 , A5 /, 8.5 11 , 5.5 8.5 , 16K , Custom (220 to 379 mm), Custom (148 to 219 mm)

Adjustment Range:

-20 (To reduce the distortion) to +20 (To reduce the dispersion)

(1 step=0.1 mm)

[02 Finisher Adjustment] (Finisher FS-531/Finisher FS-612)

This menu item is to be displayed and allowed on the machine mounted with Finisher FS-531 or Finisher FS-612.

[01 Fold & Staple Stopper]

Adjust the staple positions in Fold & Staple mode.

(Finisher FS-612 only)

Objects of adjustment:

Offset for All Size, A3 , B4 , SRA4 , A4 , 12 18 , 11 17 , 8.5 14 , 8.5 11 , 8.125 13.25 , 8.5 13 , 8.25 13 , 8 13 , 8K , 16K , Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range: -128 (To move to the right) to +127 (To move to the left)

(1 step=0.1 mm)

[02 Half-Fold Stopper Adj.]

Adjust the misalignment of the edges of printed paper.

(Finisher FS-612 only)

Objects of adjustment:

Offset for All Size, A3 , B4 , SRA4 , A4 , 12 18 , 11 17 , 8.5 14 , 8.5 11 , 8.125 13.25 , 8.5 13 , 8.25 13 , 8 13 , 8K , 16K , Custom (380 to 458 mm), Custom (279 to 379 mm)

Adjustment Range (Top of output sheet):

-128 (To lengthen the top face) to +127 (To shorten the top face)

(1 step=0.1 mm)

[03 Punch Adjustment]

This option is displayed and can be set when Punch Kit PK-512 or Punch Kit PK-513 is mounted on Finisher FS-531 or Finisher FS-612.

[01 Vertical Position Adj.]

Adjust the misalignment between the center of printed paper and the center of punch holes.

Objects of adjustment:

Offset for All Size, A3 , B4 , A4 /, B5 /, A5 /, 11 17 , 8.5 14 , 8.5 11 /, 5.5 8.5 /, 8.125 13.25 , 8.5 13 , 8.25 13 , 8 13 , 8K , 16K /, 9 11

Adjustment Range:

-50 (To move closer to front edge) to +50 (To move closer to rear edge)
(1 step = 0.1 mm)

[02 Horizontal Position Adj.]

Adjust the distance from the edge of the printed paper to the center of punch holes.

Objects of adjustment:

PI Tray, Main Body Tray

Adjustment Range:

-50 (To shorten) to +50 (To extend)
(1 step = 0.1 mm)

[03 Registration Adjustment]

Adjust the registration amount if punch positions are inclined.

Objects of adjustment:

Main Body/Reverse, Main Body/ADU, PI 1 Tray, PI 2 Tray

Adjustment Range:

-20 (Increase Registration Loop) to +20 (Reduce Registration Loop)

(1 step = 0.8 mm)

[04 Paper Edge Detect Sensor]

Automatically adjust the sensitivity of the sensor so as to correctly detect the paper edge that is used as the reference for punch holes.

Start

[04 Tri-Fold Adjustment]

Adjust the first folded positions in Tri-Fold mode.

(Finisher FS-612 only)

Objects of adjustment:

Offset for All Size, A4 , 8.5 11 , 16K

Adjustment Range:

-128 (To widen) to +127 (To narrow)

(1 step=0.1 mm)

[05 2 Pos. Staple Pitch Adj.]

Adjust the staple pitch determined in Fold & Staple and Staple modes.

Objects of adjustment:

Fold & Staple, Staple

Adjustment Range:

+128 (To narrow) to +160 (To widen)

(1 step = 1.0 mm)

[06 Post Inserter Tray Size]

This option is displayed and can be set when PostInserter PI-502 is mounted on Finisher FS-531 or Finisher FS-612.

Adjust the tray size of post inserter.

Objects of adjustment:

A4 , 8.5 11

Start

[07 Output Quantity Limit]

Specify the limit on output sheets.

When Finisher FS-531 is mounted

Objects of adjustment:

Staple 62 to 80 g/m², Staple 81 to 105 g/m², Staple 106 to 135 g/m², Staple 136 to 216 g/m²

Adjustment Range:

Staple/62 to 80 g/m²: +2 to +50
Staple/81 to 105 g/m²: +2 to +40
Staple/106 to 135 g/m²: +2 to +30
Staple/136 to 216 g/m²: +2 to +20

When Finisher FS-612 is mounted

Objects of adjustment:

Staple 62 to 80 g/m², Staple 81 to 105 g/m², Staple 106 to 135 g/m², Fold & Staple 62 to 80 g/m², Fold & Staple 81 to 105 g/m², Half-Fold 62 to 105 g/m², Tri-Fold 62 to 80 g/m²

Adjustment Range:

Staple/62 to 80 g/m², Staple/81 to 105 g/m²: +2 to +50, Staple/106 to 135 g/m²: 0, +2 to +20, Fold & Staple/62 to 80 g/m², Fold & Staple/81 to 105 g/m²: +2 to +20, Half-Fold/62 to 105 g/m², Tri-Fold/62 to 80 g/m^}2: +1 to +3

(1 step = 1 sheet)

[08 Curl Adjustment]

Displayed and allowed on the machine mounted with Finisher FS-531 or Finisher FS-612 without Relay Unit RU-509 mounted.

Make the curl adjustment for 1-sided, 2-sided, and Tri-Fold (inside print) modes.

(The curl adjustment on Tri-Fold (inside print) is available for Finisher FS-612 only.)

Objects of adjustment:

Simplex Tri-Fold/62 to 80 g/m²Inside Print,

Simplex Tri-Fold/81 to 105 g/m²Inside Print,

Simplex Except Tri-Fold/Print Side=Front/Simplex/Print Side=Back,Duplex

Adjustment Range: +0, 1, +2

[02 Finisher Adjustment] (Relay Unit RU-510)

This menu item is to be displayed and allowed on the machine mounted with Relay Unit RU-510.

This menu item is to be displayed and allowed on the machine mounted with Relay Unit RU-510.

[01 Paper Width Adjustment]

Align both ends of the output sheets in order to reduce the variation and misalignment of punch holes.

Adjustment Range:

-20 (To reduce the randomness) to +20 (To reduce the tilts)

(1 step=0.1 mm)

[02 Paper Length Adjustment]

Adjust the stop position for the lead edge of output sheets in order to reduce the variation and misalignment of punch holes.

Adjustment Range:

-50 (To reduce the dispersion) to +50 (To reduce the tilts)

(1 step=0.1 mm)

[03 Process Adjustment]

[01 Front & Back Density]

Specify the adjustment value for front and back transfer output voltage automatically set by the machine.

Objects of adjustment:

1st Transfer Y, 1st Transfer M, 1st Transfer C, 1st Transfer K, 1st Transfer (Monochrome), 2nd Transfer Front, 2nd Transfer Back

Adjustment Range: -30 to +30

[02 Maximum Density Adjustment]

Adjust the maximum density for each of Y, M, C, and K. The machine will start the Gamma Automatic Adjustment after you change the maximum density. When the Gamma Automatic Adjustment is completed, proceed to the calibration with the image controller.

Be sure to perform Color Density Manual Control after changing the maximum density.

Yellow: -10 (Light) to +10 (Dark)

Magenta: -10 (Light) to +10 (Dark)

Cyan: -10 (Light) to +10 (Dark)

Black: -10 (Light) to +10 (Dark)

[03 Max. Density Auto Adj. (RU)]

This menu item is to be displayed and allowed on the machine mounted with Relay Unit RU-509.

Automatically print and scan charts and then adjust the maximum density for each of Y, M, C, and K. The machine will start the Gamma Automatic Adjustment after you change the maximum density. When the Gamma Automatic Adjustment is completed, proceed to the calibration with the image controller. Be sure to perform Color Density Manual Control after changing the maximum density.

―

[04 Quality Adjustment]

Adjust the image quality.

[01 Printer Gamma Offset Adj.]

Change the printer gamma curve to adjust the gradation and background density in highlights.

Screen 1 (Y, M, C, K)

Screen 2 (Y, M, C, K)

Contone (Y, M, C, K)

Stochastic (Y, M, C, K)

Adjustment Range: -128 (lighter) to +127 (darker)

[02 Stabilization Adj. Setting]

Select whether to prioritize job output speed or image quality stability. When you select image quality stability, set the frequency of maximum density correction.

Speed, Stability

Customize of correction operation when image quality stable priority is selected

Maximum Density Correction: -2 (Low Frequency) to +2 (High Frequency)

[03 Custom Screen]

Select a screen to be used for Screen 1, Screen 2, and Stochastic, respectively.

Screen 1: Dot270, Dot210, Dot190, Dot175, Dot150, Dot130, Line200, Line180, Line150

Screen 2: Dot270, Dot210, Dot190, Dot175, Dot150, Dot130, Line200, Line180, Line150

Stochastic: FM1, FM2, FM3

[06 Controller Image Comp. Set]

Make this setting to smooth the jagged outlines of the text or line images.

Image Compression (1200 dpi): Gradation Priority, Resolution Priority

[05 Print Gamma Offset Auto. (RU)]

This menu item is to be displayed and allowed on the machine mounted with Relay Unit RU-509.

Make the printer gamma offset adjustment automatically using the color density sensor attached to the optional Relay Unit RU-509.

Screen 1 (Y, M, C, K)

Screen 2 (Y, M, C, K)

Stochastic (Y, M, C, K)

[06 Printer Gamma Sens. Adj.(RU)]

This menu item is to be displayed and allowed on the machine mounted with Relay Unit RU-509.

Make an adjustment for the color density sensor attached to the optional Relay Unit RU-509.

Screen 1, Screen 2, Contone, Stochastic

[07 Tone Curve for Each Tag Setting]

Execute Each Tag Adj., Do Not Execute Adjustment

[05 Execute Adjust Operation]

Execute each of the four adjustment operations manually.

Gamma Automatic Adj., Color Regist. Auto Adj., Toner Refresh Mode, Belt Refresh Mode

[06 Corner Staple (Back) Angle]

Diagonal, Parallel

[06 List/Counter]

Output the mode memory list or the audit log report. Also, collectively save the data mentioned above on the USB flash drive connected to the USB port.

Mode Memory List, User Management List, Use Management List, Font Pattern List, Audit Log Report

[07 Size Setting]

Specify the settings related to paper sizes of the paper placed in the post inserter.

[01 K Size]

Specify whether or not to use the K sizes such as 8K and 16K.

Use, Not Use

[02 A4 Tab Width Setting]

Select the tab width of A4-size tab paper.

12.7 mm, 15.0 mm

[08 Perfect Binder Setting]

This menu item is to be displayed and allowed on the machine mounted with Perfect Binder PB-503.

[01 Usable Paper Weight Select]

Set the paper weight available for body and cover paper, respectively, when using the perfect binder.

Usable Paper Weight Select

Body: 62-74g/m2 / 16-19 lb Bond, 75-80g/m2 / 20-21 lb Bond, 81-91g/m2 / 22-24 lb Bond, 92-105g/m2 / 25-28 lb Bond

Cover: 81-91g/m2 / 22-24 lb Bond, 92-105g/m2 / 25-28 lb Bond, 106-135g/m2 / 29-36 lb Bond, 136-176g/m2 / 37-47 lb Bond, 177-216g/m2 / 48-57 lb Bond

Change Weight Unit

g/m2, Duodecimo-Kg, Octavo-Kg, lb Bond, lb Index, lb Cover

[02 Paper Count Limit for PB]

Specify the minimum and maximum numbers of sheets to be bound as a body, individually for each paper weight.

This setting can be made individually for two paper types: Plain and Fine/Color Specific/Coated.

Plain:

62-74 g/m² / 16-19 lb Bond

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 200, 250, 270, 300

75-80 g/m² / 20-21 lb Bond

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 200, 250, 270, 300

81-91 g/m² / 22-24 lb Bond

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 200, 250, 270, 300

92-105 g/m² / 25-28 lb Bond

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 200, 250, 270, 300

Fine/Color Specific/Coated:

62-74 g/m² / 16-19 lb Bond

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 110, 120, 130, 140, 150

75-80 g/m² / 20-21 lb Bond

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 110, 120, 130, 140, 150

81-91 g/m² / 22-24 lb Bond

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 110, 120, 130, 140, 150

92-105 g/m² / 25-28 lb Bond

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 110, 120, 130, 140, 150

Change Weight Unit

g/m2, Duodecimo-Kg, Octavo-Kg, lb Bond, lb Index, lb Cover

[03 Unfitting Cover Stop]

Specify whether or not to stop the current job when the cover width is not suitable for the body size and spine thickness.

Temporary Stop, Not Temporary Stop

[09 Operation Screen Customize]

[01 Font Weight Setting]

Select the font weight for the screen.

Standard, Bold

[02 Machine Function Key Setting]

Change the layout of function keys displayed on the [MACHINE] screen.

-

[02 Administrator Registration]

Register the name, extension number, and e-mail address of the administrator. The administrator name and extension number are always displayed in the upper-right corner of the [UTILITY] screen.

Admin. Name Setting (up to 8 characters), Extension No. Setting (up to 5 digits), E-mail Address Setting

[03 User Auth./Account Track]

Specify whether or not to use the user authentication and account track functions. You can also specify or change the conditions in authentication.

[01 Authentication Method]

Specify the authentication method of the user authentication and account track.

User Authentication: ON (External Serv), ON (MFP), OFF

Public User: Allow, Restrict

Account Track: ON, OFF

Account Track Input Method: Account + Password, Password

Synchronize User/Account Track: Synchronize, Not Synchronize

User Distribute Number

Upper Limit Achieve Movement: Stop Immediately, Stop After Print, Warning Only

Ticket Hold Time Setting: 1 minute to 600 minutes

Count Sample Print*: ON, OFF

*Available on the machine mounted with Image Controller IC-602.

[02 User Authentication Setting]

[01 Management Setting]

Specify whether or not to display the user name list on the authentication screen. Also place the default function permissions on users for the authentication by an external server.

User Name List: ON, OFF

Default Function Permission

Print: Allow, Restrict

HDD Hold Operation: Allow, Restrict

[02 User Registration]

Add, change, or delete entries of users to be allowed in user authentication.

User No., User Name, Password, E-mail Address, Account Name, Max. Allowance Set, Usable Function (Print, HDD Hold), IC Card Registration, Output Permission (Print)(Color, Black)

[03 User Counter]

View or reset the count for each user.

-

[03 Account Track]

[01 Account Track Registration]

Change, add, or delete accounts to be tracked.

Account No., Account Name, Password, Max. Allowance Set, Usable Function (Print, HDD Hold), Output Permit(Print) (Color, Black)

[02 Account Track Counter]

View or reset the count for each account track.

-

[04 Print without Authentication]

Specify whether to make print function available to users without authentication.

Print: Allow, Restrict

[05 Auth. Device Setting]

[01 Auth. Unit Selection]

Specify the type of IC card used for entering credentials. Also, specify the authentication method.

IC Card Type: FeliCa, TypeA, SSFC, FCF, FCF (Campus)

Operation Setting: IC Card Authentication, IC Card + Password Authentication

[06 External Server Setting]

Register an external server, or edit or delete a registered server when ON (External Serv) is selected as the Authentication Method.

-

[07 User/Account Common Setting]

Specify whether or not to display a logout confirmation dialog.

Logout confirmation Display: ON, OFF

[04 Network Setting]

[01 NIC Setting]

Configure various NIC settings.

For Image Controller IC-602:
TCP/IP Setting, Netware Setting, HTTP Server Setting, WebDAV Setting, FTP Setting, SNMP Setting, SMB Setting, AppleTalk Setting, Bonjour Setting, E-mail Setting, TCP Socket Setting, OpenAPI Setting, Web Service Setting, JSP Setting, LDAP Setting, IEEE802.1X Authentication Setting, Hot Folder Setting, Advanced Setting
For Image Controller IC-415 or Image Controller IC-308:
IP Address, Subnet Mask, Gateway Address, DNS Server1, DNS Server2, Line Speed Setting: Auto, 10M Half Duplex, 10M Full Duplex, 100M Half Duplex, 100M Full Duplex

[02 E-mail Initial Setting]

Configure initial settings for e-mail or perform transmitting/receiving test.

Use E-mail System: ON, OFF

Time Zone, Trans (SMTP) Mail Server, SMTP Port Number, Trans Mail Server Timeout, New-arrival Check Interval, Receive Mail Server

Receive Mail Server Types: POP3, IMAP , POP3/IMAP Port Number, Receive Mail Account, Receive Mail Password, E-mail Address for Machine

POP (IMAP) before SMTP Auth.: ON, OFF

SSL Encryption of SMTP: ON, OFF

SSL Encryption of POP(IMAP) : ON, OFF

SMTP Authentication: ON, OFF

SMTP Authentication User ID, SMTP Authentication Password

[03 http Communication Setting]

Configure the http communication settings.

Enable Proxy Server: ON, OFF , Proxy Server Address, Proxy Server Port, Enable SSL, Enable Authentication: ON, OFF, Authentication User Name, Authentication Password

[05 Common Setting]

[One Shot Message Indication Time]

Select the time span to display a shot message in the message area of the touch panel.

3 seconds, 5 seconds

[Offset by Job Unit]

Specify whether or not to offset the output sheets by job. Also specify the number of jobs to be offset when selecting ON for this function.

ON, OFF (Selecting ON: Offset Job Number, Initial Value: 1)

[Continuation Print]

Specify whether or not to output multiple reserve jobs in succession without stopping the machine at a job break.

Printer ON, Printer OFF

[Stop Button Function]

Specify whether to pause or abort a job when Stop is pressed on the control panel.

Job Temp. Stop, Job Stop

[Back Side Magnification Adjustment]

Select whether or not to activate the back side magnification adjustment mode for both sides adjust.

ON, OFF

[Fusing Stability]

Select what to prioritize when fusing.

Best Quality, Better Quality, Speed

[Prior Paper Type]

Specify the temperature setting of the fusing section on standby. It can shorten the waiting time before printing by selecting a frequently used paper.

Others, Plain

[Dash Length (Page Stamp)]

Select the length of the dash to be used in a style of [Page No.] in [Stamp].

This setting is enabled on the machine mounted with Image Controller IC-602.

Long, Short

[Center Crop Mark Trim Margin]

Specify the space between the center crop mark and image area (center crop mark trim margin).

0.0 mm to 20.0 mm (default: 1.0)

[Schedule Cross Axis Unit (Default)]

Select the unit of horizontal axis on the [Schedule] screen.

This setting is displayed to function on the machine mounted with Image Controller IC-602.

Timetable, Time Frame (m), Sheet Volume

[Hold Job Status after Output (Default)]

Select the default value to delete or save the data of hold job after outputting.

Delete, Save

[Destination for HDD Recall (Default)]

Select the default destination for the job data recalled from the HDD.

Print, Hold, Print&Hold,

[Offset Output Mode]

Specify how to offset the output sets.

Change Out Pos., Partition Paper (Tray 1 to Tray 5, Bypass, PI 1, PI 2), Stop Print

[Needless Tab Paper Exit]

Specify whether or not to automatically discharge the oddments of tabbed sheets loaded in a tray as a set.

ON, OFF

[Banner]

This setting is displayed to function on the machine mounted with Banner Tray Unit MK-740.

ON, OFF

[Remaining Memory (Measurement Unit)]

Select the unit of displaying the remaining memory.

%, GB

[Remaining Memory (Warning)]

Select the percentage at which to give warning when the remaining memory is low.

5 % or Less, 10 % or Less

[06 System Connection]

[01 Administrator Call]

Press [Start] to call your service representative via CS Remote Care.

Start

[07 Security Setting]

[01 Administrator Password]

Change the administrator password.

00000000

[02 HDD Management Setting]

[01 HDD Lock Password]

Change the HDD lock password.

-

[02 Delete Temp. Data Setting]

Specify whether or not to overwrite the temporary image data on the memory, and also the erase mode for deleting temporary data.

Setting Switch: ON, OFF

Erase Mode: Mode 1, Mode 2

[03 Delete All Data Setting]

Select the desired erase mode to delete all the data on the HDD or the non-volatile memory of this machine. Also execute deleting all the data.

Erase Mode: Mode 1 to 8

Execute Deletion

[04 Delete hold Job]

Use this function to delete hold jobs.

-

[05 Delete HDD Job]

Use this function to delete the jobs saved on the HDD.

-

[06 HDD Restore/Backup]

Make a backup of, or restore the HDD.

[01 HDD ALL Backup]

Create a backup of all the hold job and HDD job saved on the HDD onto an external storage medium connected to the USB port.

Start

[02 HDD ALL Restore]

Restore the backup data created using [HDD ALL Backup].

Start

[03 HDD BOX Backup]

Create a backup of the jobs in the backup folder of the HDD job onto an external medium connected to the USB port.

Start

[04 HDD BOX Restore]

Restore the backup data created using [HDD BOX Backup].

Start

[05 Controller Backup]

Create a backup of setting data saved on the Image Controller IC-602 onto an external storage medium connected to the USB port.

Start

[06 Controller Restore]

Restore the backup data created using [Controller Backup].

Start

[07 HDD Encryption Setting]

Set whether or not to save all jobs saved on the HDD upon encrypting them, and set the encryption password.
* HDD encryption setting is not displayed by default. To use this setting, please contact your service representative.

ON, OFF
12345678

[07 Hold Job Auto Delete Period]

Set the time when the jobs on hold are automatically deleted.

Not Delete, 12 hours, 1 day, 2 days, 3 days, 7 days, 30 days

[03 Enhanced Security Mode]

Specify whether or not to activate the Enhanced Security mode.

ON, OFF

[01 Quick IP Filtering]

Restrict access to the machine by means of IP address (IPv4/IPv6).

Filtering Method: No Filtering, Sync. IP Address, Sync. Subnet Mask

IPv4 Access Range, IPv6 Access Range

[02 Administrator Password]

Set an administrator password for the machine on which the administrator authentication function is set to OFF. The administrator authentication function is automatically turned ON.

Current Password, New Password, Input Confirmation

[03 Password Rules Setting]

Select whether or not to enable the password rules.

Enable, Disable

[04 WebUtilities Setting]

Select whether or not to use the functionality of Web Utilities.

ON, OFF

[05 PSWC Setting]

Select whether or not to use the functionality of PageScope Web Connection. This setting is displayed and available on the machine mounted with Image Controller IC-602.

ON, OFF

[06 Security Warning Display]

Select whether or not to display the Security Setting Warning screen.

Display, Not Display