UTILITY items (AccurioPress 6136P)

01 Language Setting

Select the language used in the touch panel and voice messages.

Language Used in LCD: Japanese, Hangul, Taiwan, Chinese, English, French, German, Italian, Spanish

Language in Voice Message: English, Japanese, OFF

02 Unit Setting

Select the unit of measurement for numeric values to be displayed on the touch panel.

mm, Inch(Decimal Point), Inch(Fraction)

03 Paper Tray Setting

01 Paper Setting

01 Paper Profile Setting

Register or delete the paper settings. Up to 500 can be registered.

Paper Type, Profile Name, Paper Size, Weight, Colored Paper, Punch, Both Sides Adj., RU Curl Adj., Expert Adj., Curl Adjustment, Color Density

Import, Export

02 Preset Profile Management

Allows you to add or delete a profile.

Search Condition of profile

USB Import of Preset Profile, Delete, Add Profile

Delete of Paper Profile

02 Auto Tray Selection Setting

Select the tray to take over the feeding when the tray currently used becomes out of paper. This function is called Auto Tray Switch (ATS). When selecting multiple trays for ATS, determine the priority of the trays.

ATS/APS Switch: Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11

Tray Priority: Order of priority for selected trays

03 Type for Auto Paper

Specify paper conditions that enable a tray to be selected in Auto Paper (APS).

Paper conditions to be specified here are Paper Type, Weight, Punch, Tab Paper, and Colored Paper.

Paper Type: Plain, Fine, Coated, PrePrinted, Book/News, Plain-rough, Blank Insert, Textured

Weight(g/m2): 40-49g/m2/10-13 lb Bond, 50-54g/m2/14-15 lb Bond, 55-61g/m2/16-17 lb Bond, 62-74g/m2/18-19 lb Bond, 75-80g/m2/20-21 lb Bond, 81-91g/m2/22-24 lb Bond, 92-105g/m2/25-28 lb Bond, 106-135g/m2/29-36 lb Bond, 136-162g/m2/37-43 lb Bond, 163-216g/m2/44-57 lb Bond, 217-256g/m2/58-68 lb Bond, 257-300g/m2/69-81 lb Bond, 301-350g/m2/82-93 lb Bond

Punch: Allow, Restrict

Tab Paper: Allow, Restrict

Colored Paper: White, Blue, Goldenrod, Gray, Green, Ivory, Orange, Pink, Red, Yellow, Cream, Clear White, Others, User Color

04 Dehumidify Fan Heater

Configure operation settings for the dehumidifying fan heater of Paper Feeder Unit (Tray 3 to Tray 11) and Large Capacity Post Inserter PI-PFU (PI-PFU1 to PI-PFU3).

Dryness Preparation: ON, OFF

Fan Heater Control(Tray3), Fan Heater Control(Tray4), Fan Heater Control(Tray5), Fan Heater Control(Tray6), Fan Heater Control(Tray7), Fan Heater Control(Tray8), Fan Heater Control(Tray9), Fan Heater Control(Tray10), Fan Heater Control(Tray11), Fan Heater Control(PI-PFU1), Fan Heater Control(PI-PFU2), Fan Heater Control(PI-PFU3): Auto, Compulsively ON, Compulsively OFF

04 Reset Setting

01 Auto Reset Setting

The machine automatically restores the screen specified as the default screen after a certain period of inactivity. Select the time interval to activate this function.

OFF, 60 seconds, 120 seconds, 180 seconds, 240 seconds, 300 seconds, 360 seconds, 420 seconds, 480 seconds, 540 seconds

05 Default Screen Setting

Select the screen to be displayed when the sub power switch is turned on or Auto Reset is activated.

MACHINE, JOB LIST/Hold Job, JOB LIST/Reserved Job

06 Power Save Setting

01 Power Save Function Setting
Select the time to activate Auto Low Power and Auto Shut OFF. Also select either Auto Low Power or Auto Shut OFF to be activated when Power Save is pressed on the control panel.

You can also select the condition of Auto Wake-up to activate the machine when a print job is received during Auto Shut OFF.

Auto Low Power: --- min., 0.5 min., 3 min., 5 min., 10 min., 15 min., 30 min., 60 min., 90 min., 120 min., 240 min.
Auto Shut OFF: --- min., 0.5 min., 3 min., 5 min., 10 min., 15 min., 30 min., 60 min., 90 min., 120 min., 240 min.
Power Save Function: Auto Low Power, Auto Shut OFF

Auto Wake-up Cond.: All Jobs

02 ErP Setting

Automatically turn off the main power switch when the sub power switch is turned off, or when Auto Shut OFF or Auto Low Power has been active for a certain time.

Do Not Switch, 12 Hours, 24 Hours, 36 Hours, 48 Hours, 60 Hours, 72 Hours

03 Main Power Auto OFF Setting

Select whether to automatically turn OFF the main power switch after the sub power switch is turned OFF and the main body has completely cooled down.

If turned ON, the above function is set.

ON, OFF

07 Date/Time Setting

Set the current date and time, the daylight-saving time, and the time difference.

Setting Time

Daylight Saving Time: OFF, ON (1 to 150 min.)

Time Zone: -12:00 to +13:00 (Default: +00:00)

08 Operation/Info. Sound Setting

01 Volume Setting

Specify whether to turn the operation sound and speaker sound on or off, and also set the volume when they are turned on.

Operation Sound: ON, OFF, (Small) 1, 2, 3, 4, 5, 6, 7, 8 (Big)

Speaker Sound: ON, OFF, (Small) 1, 2, 3, 4, 5, 6, 7, 8, 9, 10 (Big) 

02 Info. Sound Item Setting

Specify each items provided for information sound and voice message.

Repeat Number Setting

Info. Sound Repeat Number: 1 time, 2 times, 3 times

Voice Repeat Number: 1 time, 2 times, 3 times

Notice Set for Machine Stop

Paper JAM: Voice, Info. Sound, OFF

Paper Empty: Voice, Info. Sound, OFF

Paper Differ: Voice, Info. Sound, OFF

Replenish Toner: Voice, Info. Sound, OFF

Service Call: Info. Sound, OFF

Output Full: Info. Sound, OFF

Other Notification Setting

Job Complete Pre-notice: Voice, OFF

Stop Button Acceptance: Voice, OFF

Sample Print Completion: Voice, OFF

Finisher Front Door Alert: Voice, OFF

Other Info. Sound Setting

For System Starting: Info. Sound, OFF

For Sample Printing: Info. Sound, OFF

For Print Job Receiving: Info. Sound, OFF

09 Key Response Time

Select the time interval to get the response from the machine when a key is pressed on the touch panel.

Normal, 0.5 seconds, 1 second, 2 seconds, 3 seconds

10 Service Port Device Setting

Specify whether or not to use a service port device, and select the keyboard type if the service port device is used.

Service Port Device: ON, OFF

Keyboard Type: EN65, EN104, JP101, JP106, JP109, UK, FR, IT, DE, ES

11 Mouse Setting

Select whether or not to use the Wheel Booster function and Cursor Auto Scrolling function, respectively, for when the mouse is connected.

Wheel Booster Setting: ON, OFF

When using this function, set List Scrolling Speed and Value Scrolling Speed.

Cursor Auto Scrolling Set.: ON, OFF

When using this function, set Cursor Speed, Cancel Sensitivity, Cursor Prior Return Pos.Set., and Cursor PriorDestination Set..

One Shot Message Indication Time

Select the time span to display a shot message in the message area of the touch panel.

3 seconds, 5 seconds

Offset by Job Unit

Specify whether or not to offset the output sheets by job. Also specify the number of jobs to be offset when selecting ON for this function.

ON, OFF (Selecting ON: Offset Job Number)

Continuation Print

Specify whether or not to output multiple reserve jobs in succession without stopping the machine at a job break.

Printer ON, Printer OFF

Dark Tone Control

In order to adjust the quality of the output image, select whether to automatically decrease the output speed (Quality), prioritize the output speed, or disable the ability to control the tone.

OFF, Quality, Performance

Icon Display for Dark Tone Control

Select whether or not to display the Dark Tone icon while the Dark Tone Control function is enabled.

This function is available only when Quality or Performance is selected at Dark Tone Control.

ON, OFF

Dash Length(Page Stamp)

Select the length of the dash to be used in a style of Page No. in Stamp.

Long, Short

Center Crop Mark Trim Margin

Specify the space between the center crop mark and image area (center crop mark trim margin).

0.0 mm-20.0 mm (Default: 1.0)

Schedule Cross Axis Unit (Default)

Select the unit of horizontal axis on the Schedule screen.

Timetable, Time Frame(m), Sheet Volume

Hold Job Status after Output (Default)

Select the default value to delete or save the data of hold job after outputting.

Delete, Save

Hold Job Direct Output (Default)

Select the default for the Direct Output check box under the Hold Job screen.

ON selects the check box, and OFF clears the check box.
After the change, turn OFF/ON the sub power switch to apply the setting.

ON, OFF

Offset Output Mode

Specify how to offset the output sets.

Change Out Pos., Stop Print, Change Out Pos. + Partition Paper (Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11, PI1, PI2, PI-PFU1, PI-PFU2, PI-PFU3), Partition Paper (Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11, PI1, PI2, PI-PFU1, PI-PFU2, PI-PFU3)

Needless Tab Paper Exit

Specify whether or not to automatically discharge the oddments of tabbed sheets loaded in a tray as a set.

ON, OFF

Remaining Memory (Measurement Unit)

Select the unit of displaying the remaining memory.

%, GB

Remaining Memory (Warning)

Select the percentage at which to give warning when the remaining memory is low.

5% or Less, 10% or Less

[Proof Copy] 1 Set/1st Sheet Selection

If it is turned ON, the confirmation window is opened and you are asked to output one confirmation copy or to output only its first page when the Proof Copy is pressed.

ON, OFF

Temp. Down/Up Control before Print

Select whether to rotate the fusing roller before printing starts, in order to print at the appropriate temperature.

ON, OFF

Both Sides Rotate/Skew

If Disable is selected, the Rotate/Skew adjustment does not become available and does not function.

Enable, Disable

Stop when Water Tank Near Empty

Select whether to temporarily stop a job when the humidifier tank runs low on water.

Temporary Stop, NotTemporaryStop

Select Chart Type (Auto Image Adj.)

Select an automatic image adjustment chart for each paper weight. The unit of weight can be switched.

This option is displayed when Integrated Color Care Unit IQ-501 is mounted on the machine.

40-49g/m2/10-13 lb Bond: Type1, Type2

50-54g/m2/14-15 lb Bond: Type1, Type2

55-61g/m2/16-17 lb Bond: Type1, Type2

62-74g/m2/18-19 lb Bond: Type1, Type2

75-80g/m2/20-21 lb Bond: Type1, Type2

81-91g/m2/22-24 lb Bond: Type1, Type2

92-105g/m2/25-28 lb Bond: Type1, Type2

106-135g/m2/29-36 lb Bond: Type1, Type2

136-162g/m2/37-43 lb Bond: Type1, Type2

163-216g/m2/44-57 lb Bond: Type1, Type2

217-256g/m2/58-68 lb Bond: Type1, Type2

257-300g/m2/69-81 lb Bond: Type1, Type2

301-350g/m2/82-93 lb Bond: Type1, Type2

Change Unit

Auto Image Adjustment Deviation Check

Select whether to automatically check a deviation. If you select ON, enter the specified value of a deviation.

This option is displayed when Integrated Color Care Unit IQ-501 is mounted on the machine.

ON (ON: 0.5 mm-10.0 mm, Default: 2.0), OFF

Operation after Deviation/Out of Range was Detected

Specify the operation to be performed when inappropriate output paper is detected.

You can specify whether to stop this machine immediately or only when the number of detected errors exceeds the standard.

* When the standard value for the number of detected errors is set to 0, and Automatic Reprint when Deviation/Out of Range was Detected is set to OFF, this machine will not stop even if the number of detected errors increases.

This option is displayed when Integrated Color Care Unit IQ-501 is mounted on the machine.

Stop, Continue Output, Detection Count (0 ~ 10 times)

Partition Paper when Deviation/Out of Range was Detected

Configure a setting to insert partition paper when inappropriate output paper is detected.

When inserting, select the paper tray to load partition paper into.

This option is displayed when Integrated Color Care Unit IQ-501 is mounted on the machine.

ON, OFF, Partition Paper (Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11)

Automatic Reprint when Deviation/Out of Range was Detected

Configure a setting to perform reprinting when inappropriate output paper is detected. When reprinting is performed, paper in the machine is output once, so a page order error involving output paper does not occur.

This option is displayed when Integrated Color Care Unit IQ-501 is mounted on the machine.

ON, OFF

Output Tray for Out of Range

Specify the tray to output paper that does not satisfy the standard. You can combine the Purge Tray of the Relay Unit RU-702 with a sub tray of the optional output unit mounted later, and also select the same tray for a job.

* Paper cannot be output to the sub tray of Folding Unit FD-503, Large Capacity Stacker LS-506, or Saddle Stitcher SD-506. Also, paper cannot be output to the sub tray of Saddle Stitcher SD-513 when the Multi Tri-Fold, Fold & Staple, or Half-Fold mode is being used.

* When a paper output enabled option is not connected to Relay Unit RU-702 or later, the button of RU702 + Sub Tray is grayed out.

This option is displayed when Integrated Color Care Unit IQ-501 is mounted on the machine.

Same as the Job, Purge Tray (RU702 Only, RU702 + Sub Tray)

Create Auto Inspection Report

Configure a setting to create an automatic inspection result report.

When inappropriate output paper is not discharged automatically, the user deals with the inappropriate output paper based on the report.

This option is displayed when Auto Inspection Unit UK-301 is mounted.

ON, OFF

Automatic Inspection Level Setting

Adjust the detection standard for automatic inspection. There are three levels: Essential, Standard, and Premium, for each of which you can adjust the detection standard.

This option is displayed when Auto Inspection Unit UK-301 is mounted.

Spot Detection Level

Specify the reference value of the spot size. A spot that is over the reference size value is detected as an image failure.

Range: 1(Large) ~ 7(Small)

Paper Noise Removal Level

Specify the reference value of spot density. A spot that is over the reference density value is detected as an image failure.

Range: 1(Strong) ~ 7(Weak)

Image Edge Detection Sensitivity

Specify the sensitivity of the inspection area around the edge of the image. A slight image misalignment may occur around the edge of the image even if no image failure is detected; therefore, if the sensitivity is set to a higher level, it may lead to frequent reprinting.

Range: 1(Low) ~ 7(High)

Permission Level for Spot

Specify the reference value that permits an image spot detected in a reference image.

An image failure may be slipped into a reference image when it is created. If automatic inspection is performed in this status, the inspection image is detected as an error even if there is "no error". In such a case, reduce this reference value; an image failure of a reference image is permitted to a certain degree, which enables smooth printing.

Range: 1(Large) ~ 7(Small)

Wait Screen for Automatic Inspection

Set the automatic inspection on the Wait screen. When outputting a print job for Direct Print and such without temporarily saving it, input the job in Wait mode; you can set the automatic inspection.

This option is displayed when Auto Inspection Unit UK-301 is mounted.

ON, OFF

Reference Image Automatic Deletion

Configure a setting to automatically delete the reference image that is created for automatic inspection. When the amount of available reference image memory is not sufficient, the reference image of the oldest update date and time in Reference Image List 1 is deleted automatically.

This option is displayed when Auto Inspection Unit UK-301 is mounted.

ON, OFF

01 Outline Process

Select the Outline Process for printing.

Text Thinning: Weak+, Weak, Normal, Strong, Strong+

Halftone Text Enhancement: Weak+, Normal, Strong+

FD Lead Edge Density Adjustment: -5, -4, -3, -2, -1, 0

FD Rear Edge Density Adjustment: 0, +1, +2, +3, +4, +5

02 Select Prior Output Tray

Select the output tray for the jobs for which the output tray is specified as "Auto". This menu item is to be displayed and allowed on the machine mounted with Finisher FS-532.

Main Tray, Sub Tray

01 Tandem Machine One Time Data Read

Set the Partner MFP to receive all the data transmitted from This MFP before starting to print.

ON, OFF

02 Tandem Machine Wait/Proof

Set whether to transmit the data to the Partner MFP when This MFP starts scanning the data for proof copying.

Allow, Restrict

03 Distribution Recovery

Set the tandem-connected machines to perform the job distribution again for print quantity remaining on one machine when the other has already finished with its assignment.

ON, OFF

04 Tandem IP Address Setting

Specify the IP address of the Partner MFP.

IPv4 Address

01 Power Save Setting

01 Power Save Function Setting
Select the time to activate Auto Low Power and Auto Shut OFF. Also select either Auto Low Power or Auto Shut OFF to be activated when Power Save is pressed on the control panel.

You can also select the condition of Auto Wake-up to activate the machine when a print job is received during Auto Shut OFF.

Auto Low Power: --- min., 0.5 min., 3 min., 5 min., 10 min., 15 min., 30 min., 60 min., 90 min., 120 min., 240 min.

Auto Shut OFF: --- min., 0.5 min., 3 min., 5 min., 10 min., 15 min., 30 min., 60 min., 90 min., 120 min., 240 min.

Power Save Function: Auto Low Power, Auto Shut OFF

Auto Wake-up Cond.: All Jobs

02 ErP Setting

Automatically turn off the main power switch when the sub power switch is turned off, or when Auto Shut OFF or Auto Low Power has been active for a certain time.

Do Not Switch, 12 Hours, 24 Hours, 36 Hours, 48 Hours, 60 Hours, 72 Hours

03 Main Power Auto OFF Setting

Select whether to automatically turn OFF the main power switch after the sub power switch is turned OFF and the main body has completely cooled down.

If turned ON, the above function is set.

ON, OFF

02 Date/Time Setting

Set the current date and time, the daylight-saving time, and the time difference.

Setting Time

Daylight Saving Time: OFF, ON (1 to 150 min.)

Time Zone: -12:00 to +13:00 (Default: +00:00)

03 Weekly Timer Setting

01 Weekly Timer ON/OFF Setting

Specify whether or not to use the Weekly Timer function.

Weekly Timer ON, Weekly Timer OFF

02 Time Setting

Set the ON/OFF times in hours and minutes.

―

03 Date Setting

Set the ON/OFF condition of the machine for a given day of a given month.

―

04 Select Time for Power Save

Set the machine to turn off and then on during the lunch break.

ON, OFF

05 Password Non-Business Hours

Set a password to use the machine by turning on the power temporarily while the machine is in off condition due to the Weekly Timer function.

Default password: 0000 (4 digits)

04 Restrict User Access

01 Function Usage Restriction

Specify whether or not to allow the use of various functions.

Sample Print: Allow, Restrict

USB Direct Print: Allow, Restrict

05 Expert Adjustment

01 Printer Adjustment

01 Restart Timing Adjustment

Adjust the image position of lead edge in paper feed direction in the printer engine.

Prerequisite:

FD-Mag. Adjustment is completed.

Objects of adjustment:

Side1: All Trays Offset

Adj. Range: -45~+45 1 step = 0.1 mm

Side1, Side2: Restart Timing (Tray1), Restart Timing (Tray2), Restart Timing (Tray3), Restart Timing (Tray4), Restart Timing (Tray5), Restart Timing (Tray6), Restart Timing (Tray7), Restart Timing (Tray8), Restart Timing (Tray9), Restart Timing (Tray10), Restart Timing (Tray11)

Adj. Range: -30~+30 1 step = 0.1 mm

[-] Lower [+] Higher

02 Centering Adjustment

Adjust the image position in the crosswise direction of the printer engine.

Prerequisite:

CD-Mag. Adjustment is completed.

Adj. Range: -64~+63 1 step = 0.1 mm

[-] Front [+] Back

03 FD-Mag. Adjustment

Adjust the magnification in paper feed direction in the printer engine.

Objects of adjustment:

Side1: Printer FD-Mag.

Adj. Range: -10~+10 1 step = 0.05 %

Objects of adjustment:

Side2: Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11

Adj. Range: -10~0 1 step = 0.05 %

[-] Short [+] Long

04 CD-Mag. Adjustment

Adjust the magnification in crosswise direction in the printer engine.

Objects of adjustment:

Side1: Printer CD-Mag.

Adj. Range: -10~+10 1 step = 0.05 %

Objects of adjustment:

Side2: Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11

Adj. Range: -10~0 1 step = 0.05 %

[-] Short [+] Long

05 Registration Loop Adj.

Adjust the paper loop amount in registration roller section.

Objects of adjustment:

Side1

Adj. Range: -7~+10 1 step = 1.0 mm

Objects of adjustment:

Side1 Thick

Adj. Range: 0~+10 1 step = 1.0 mm

Objects of adjustment:

Side1 Thin

Adj. Range: -6~+10 1 step = 1.0 mm

Objects of adjustment:

Side2, Side2 Thick, Side2 Thin

Adj. Range: -10~+10 1 step = 1.0 mm

[-] Short [+] Long

06 Pre-registration Adj.

Adjust the paper loop amount in pre-registration roller section of the trays.

Objects of adjustment:

Not Thin Paper, Thin Paper

Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11

Adj. Range: -10~+10 1 step = 1.0 mm

[-] Short [+] Long

07 Print Job JAM Setting

Set whether or not to stop the machine as a paper jam when a mis-centering is detected. Select whether to display a message when the machine stops due to a paper jam or double feeding.

Mis-centering JAM Setting: Detect, Not Detect

JAM Identification Display: Display, Not Display

02 Finisher Adjustment (Finisher FS-532)

This menu item is to be displayed and allowed on the machine mounted with Finisher FS-532.

01 Staple Finisher Adjustment

01 Staple Finisher(Main)Adj.

01 Exit Guide Paper Width Adj.

Adjust the exit guide alignment pitch to be used by the staple finisher.

Make adjustment if output paper stack on main tray is uneven in straight delivery.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 short edge feed, A4 long edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, 8.5 14 short edge feed, 8 13 short edge feed, B5 short edge feed, Postcard, 5.5 8.5 long edge feed, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] Wide [+] Narrow

02 Upper Gripper Operation

Select the upper gripper operation for main tray outlet.

Auto, ON, OFF

03 Output Alignment Operation

Select operation for output alignment.

Auto, ON, OFF

04 Staple Paper Width Adj.

Adjust the board alignment width of the staples in the staple finisher.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm)

Adj. Range: -20~+20 1 step = 0.1 mm

[-] Wide [+] Narrow

05 FD Alignment Plate Adj.

Adjust the vertical alignment fitting for staples in the staple finisher.

Objects of adjustment:

Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, 9 11 long edge feed, 5.5 8.5 long edge feed, Custom(139~230 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] Wide [+] Narrow

06 Staple Position Adjustment

Adjust 2 position staple pitch and corner staple positions in staple finisher.

Objects of adjustment:

2 Position Pitch(120 mm), 2 Position Pitch(140 mm), 2 Position Pitch(165 mm), Rear Diagonal

Adj. Range: -5~+5 1 step = 1 mm

Objects of adjustment:

Rear Parallel, Front Parallel

Adj. Range: -3~+3 1 step = 1 mm

[-] Narrow [+] Wide

07 Rewind Paddle Descent Adj.

Adjust rewind paddle descent.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 short edge feed, A4 long edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm)

Adj. Range: -10~+10 1 step = 0.2 mm

[-] Little [+] Much

08 Rewind Function Operation

Select the rewind paddle operation.

Auto, ON, OFF

02 Staple Finisher(Fold)Adj.

This menu item is to be displayed and become configurable on Finisher FS-532 mounted with Saddle Stitcher SD-510.

01 Fold&Staple Paper Width Adj.

Adjust pitch of alignment plate in Saddle Stitcher SD-510 if half-folded or multi tri-folded sheets show misalignment.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] Narrow [+] Wide

02 Fold&Staple Pitch Adjustment

Adjust staple pitch in Saddle Stitcher SD-510. Make this adjustment if staple pitch is not within the allowance range.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm)

Adj. Range: -300~+300 1 step = 0.1 mm

Staple pitch: [-] Narrow [+] Wide

03 Fold&Staple Fold Position

Adjust half-fold position of fold & staple function in Saddle Stitcher SD-510. Make this adjustment if half-fold position is not within the specified range.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

Top face of output paper: [-] Extend [+] Shorten

04 Fold&Staple Staple Position

Adjust staple position in Saddle Stitcher SD-510.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

Top face of output paper: [-] Extend [+] Shorten

05 Half-Fold Fold Position Adj.

Adjust half-fold position of fold function in Saddle Stitcher SD-510.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

Top face of output paper: [-] Extend [+] Shorten

06 Tri-Fold Adjustment

01 Tri-Fold Position Adjustment

Adjust Fold 1 and Fold 2 positions for multi tri-folding in Saddle Stitcher SD-510.

Make this adjustment if each fold position for tri-folding is not within the allowance range.

Objects of adjustment:

8.5 11 short edge feed, A4 short edge feed, 16K short edge feed

Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm

Fold 1: [-] Extend [+] Shorten

Fold 2: [-] Shorten [+] Extend

02 Double Fold Plate Adjustment

Adjust double fold plate in saddle stitcher.

Deepen in case of wide shift in bunch of the Fold 2.

Objects of adjustment:

8.5 11 short edge feed, A4 short edge feed, 16K short edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

Quantity of inserting double fold plate: [-] Shallow [+] Deep

07 Half-Fold Strength Adj.

To adjust the opening of booklets, increase the roller pressure time.

* You cannot adjust the strength to fold booklets.

* Long pressure time causes reduced productivity.

Adj. Range: 0~+10 1 step = 1 sec

03 Staple Finisher(Punch)Adj.

This menu item is to be displayed and configurable on Finisher FS-532 mounted with Punch Kit PK-522.

01 Registration Adjustment

If the punch position is not parallel to the paper edge, control the paper curl and wrinkle by adjusting the paper loop amount of the registration roller.

Adj. Range: -50~+50 1 step = 0.1 mm

[-] Short [+] Long

02 Horizontal Position Adj.(FD)

Adjust the distance between the edge of the printed paper and the center of punch holes.

Objects of adjustment:

Offset for All Size, A3 short edge feed, A4 long edge feed, A4 short edge feed, SRA4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 8.5 14 short edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 9 11 long edge feed, B5 short edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

Punch position at paper edge: [-] Far [+] Close

03 Vertical Position Adj.(CD)

Adjust the misalignment in center positions of paper and punch holes for each paper size.

Objects of adjustment:

Offset for All Size, A3 short edge feed, A4 long edge feed, A4 short edge feed, SRA4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 8.5 14 short edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 9 11 long edge feed, B5 short edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

Punch position: [-] Forward [+] Backward

04 Staple Finisher(PI)Adj.

This menu item is to be displayed and configurable on Finisher FS-532 mounted with Post Inserter PI-502.

01 PI Registration Adjustment

When paper fed from the Upper Tray or Lower Tray of Post Inserter PI-502 has skew or wrinkle, or causes paper jam, adjust the paper loop of the registration roller.

Objects of adjustment:

PI Upper Tray, PI Lower Tray

Adj. Range: -5~+5 1 step = 1 mm

[-] Short [+] Long

02 Finisher Adjustment (Output Tray OT-510)

This menu item is displayed and can be set on the machine mounted with Output Tray OT-510.

01 Staple Finisher Adjustment

01 Staple Finisher(Main)Adj.

01 Exit Guide Paper Width Adj.

Adjust the exit guide alignment pitch to be used by the staple finisher.

Make adjustment if output paper stack on main tray is uneven in straight delivery.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5  14 short edge feed, 8  13 short edge feed, B5 short edge feed, Postcard, 5.5 8.5 long edge feed, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] Wide [+] Narrow

02 Upper Gripper Operation

Select the upper gripper operation for main tray delivery exit.

Auto, ON, OFF

03 Output Alignment Operation

Select operation for output alignment.

Auto, ON, OFF

02 Finisher Adjustment (Folding Unit FD-503)

This menu item is to be displayed and allowed on the machine mounted with Folding Unit FD-503.

02 Multi Folder Adjustment

01 Multi Folder(Punch)Adj.

01 Paper Width Adjustment

Adjust the misalignment of punch hole positions.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, A4 long edge feed, B5 short edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, 16K long edge feed, 9 11 long edge feed, 5.5 8.5 long edge feed

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the randomness [+] To reduce the tilts

02 Punch Vertical Position Adj.

01 2-Hole Punch

Adjust the vertical position of punch holes made by the folding unit.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, A4 long edge feed, B5 short edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, 16K long edge feed, 9 11 long edge feed, 5.5 8.5 long edge feed

Adj. Range: -40~+40 1 step = 0.1 mm

[-] To move to the center [+] To move to the edge

02 3-Hole Punch

Adjust the vertical position of punch holes made by the folding unit.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, A4 long edge feed, B5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 11 long edge feed, 8K short edge feed, 16K long edge feed, 9 11 long edge feed

Adj. Range: -40~+40 1 step = 0.1 mm

[-] To move to the center [+] To move to the edge

02 4-Hole Punch

Adjust the vertical position of punch holes made by the folding unit.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, A4 long edge feed, B5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 11 long edge feed, 8K short edge feed, 16K long edge feed, 9 11 long edge feed

Adj. Range: -40~+40 1 step = 0.1 mm

[-] To move to the center [+] To move to the edge

02 Multi Folder(Fold)Adj.

01 Half-Fold Position Adj.

Adjust the folded position for half-fold.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To shorten the top face [+] To lengthen the top face

02 Z-Fold Position Adj.

Adjust the fold positions for Z-folding.

Start with Fold 1, and then set Fold 2.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm)

Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm

Fold 1: To narrow [-] <-> [+] To widen

Fold 2: To narrow [-] <-> [+] To widen 

03 Tri-Fold-in Pos. Adj.

Adjust the fold positions for tri-fold-in.

Start with Fold 1, and then set Fold 2.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm)

Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm

Fold 1: To narrow [-] <-> [+] To widen

Fold 2: To narrow [-] <-> [+] To widen

04 Tri-Fold-out Pos. Adj.

Adjust the fold positions for tri-fold-out.

Start with Fold 1, and then set Fold 2.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm)

Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm

Fold 1: To widen [-] <-> [+] To narrow

Fold 2: To narrow [-] <-> [+] To widen

05 Double Parallel Pos. Adj.

Adjust the fold positions for double parallel folding.

Start with Fold 1, and then set Fold 2.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm)

Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm

Fold 1: To narrow [-] <-> [+] To widen

Fold 2: To narrow [-] <-> [+] To widen

06 Gate Position Adj.

Adjust the fold position for gate folding.

Start with Fold 1, and then set Fold 2 and Fold 3.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm)

Fold 1, Fold 2, Fold 3: Adj. Range: -50~+50 1 step = 0.1 mm

Fold 1: To narrow [-] <-> [+] To widen

Fold 2: To widen [-] <-> [+] To narrow

Fold 3: To narrow [-] <-> [+] To widen

02 Finisher Adjustment (Large Capacity Stacker LS-506)

This menu item is to be displayed and allowed on the machine mounted with Large Capacity Stacker LS-506.

When three stackers are mounted, a setting can be configured for each stacker.

03 Stacker Adjustment

01 Paper Width Adjustment

Adjust the position of adjustment plates if output sheets show misalignment in crosswise direction on the stacker tray.

Objects of adjustment:

Stacker No.1, Stacker No.2, Stacker No.3

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the dispersion [+] To reduce the distortion

02 Paper Length Adjustment

Adjust the position of the stopper if output sheets show misalignment in paper feed direction on the stacker tray.

Objects of adjustment:

Stacker No.1, Stacker No.2, Stacker No.3

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the dispersion [+] To reduce the distortion

02 Finisher Adjustment (Saddle Stitcher SD-506)

This menu item is to be displayed and allowed on the machine mounted with Saddle Stitcher SD-506.

04 Saddle Stitcher Adjustment

01 Fold Paper Width Adj.

Adjust the width of adjustment plates if half-folded or tri-folded sheets show misalignment.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To reduce the misalignment [+] To reduce the distortion

02 Half-Fold Position Adj.

Adjust the fold position determined by the half-folder.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To shorten the top face [+] To lengthen the top face

03 Staple Paper Width Adj.

Adjust the width of adjustment plates of the saddle stitcher to be used in Staple mode.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm)

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the dispersion [+] To reduce the distortion

04 Staple Center Position

Adjust the center position of staples determined by the saddle stitcher.

Prerequisite: Staple paper width adjustment is completed.

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To move closer to paper center (fold) [+] To move away from paper center (fold)

05 Staple Pitch Adjustment

Adjust the staple pitch determined by the saddle stitcher.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm)

Adj. Range: -20~+20 1 step = 1.0 mm

[-] To shorten [+] To lengthen

06 Trimming Adjustment

Adjust the trimming width.
The trim width should be more than 2.0 mm, otherwise the trimming operation may not be performed properly.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm)

Adj. Range: -400~+400 1 step = 0.1 mm

[-] To narrow [+] To widen

07 Tri-Fold Position Adj.

Adjust the folded positions in Tri-Fold mode.

Start with Fold 1, and then set Fold 2.

Objects of adjustment:

Offset for All Size, A4 short edge feed, 8.5 11 short edge feed

Fold 1, Fold 2: Adj. Range: -100~+100 1 step = 0.1 mm

Fold 1: To widen [-] <-> [+] To narrow

Fold 2: To narrow [-] <-> [+] To widen

08 Trimmer Receiver Adj.

Frequent trimming operations may cause damage to the receiver, resulting in trimming failures. Move the receiver automatically or manually.

*Trimmer Receiver Adj. is not displayed by default. To use this setting, please contact your service representative.

Objects of adjustment: Trim Count

Adjustment range: 700 times, 500 times, 300 times

Objects of adjustment: Move Pitch

Adjustment range: 1.0 mm, 1.5 mm, 2.0 mm

Execute Compulsive Movement

02 Finisher Adjustment (Saddle Stitcher SD-513)

This menu item is to be displayed and allowed on the machine mounted with Saddle Stitcher SD-513.

04 Saddle Stitcher Adjustment

01 Fold Paper Width Adj.

Adjust the width of adjustment plates if half-folded or tri-folded sheets show misalignment.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, PI Paper, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To reduce the misalignment [+] To reduce the distortion

02 Fold Skew Adjustment

Adjust the skew of the folding line.

Objects of adjustment: Single Fold, Multi Fold

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, PI Paper, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To weaken [+] To strengthen

03 Half-Fold Position Adj.

Adjust the folded position for half-fold.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To shorten the top face [+] To lengthen the top face

04 Tri-Fold Position Adj.

Adjust the folded positions in Tri-Fold mode.

Adjust Fold 1 and Fold 2 in this order.

Objects of adjustment:

Offset for All Size, A4 short edge feed, 8.5 11 short edge feed

Fold 1: Offset for All Size, A4 short edge feed

Adj. Range: -100~+90 1 step = 0.1 mm

Fold 1: 8.5 11 short edge feed

Adj. Range: -100~+30 1 step = 0.1 mm

Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm

[-] To widen [+] To narrow

05 Crease Position Adjustment

Adjust the crease position.

01 Half-Fold Crease Position

Move the half-fold crease position.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To shorten [+] To lengthen

02 Tri-Fold Crease Position

Move the tri-fold crease position.

Objects of adjustment:

Offset for All Size, A4 short edge feed, 8.5 11 short edge feed

Fold 1, Fold 2: Adj. Range: -20~+20 1 step = 0.1 mm

[-] To shorten [+] To lengthen

03 PB Cover Crease Position

Move the perfect binding cover crease position.

Objects of adjustment:

Crease Line 1, Crease Line 2: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13  19 short edge feed

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To shorten [+] To lengthen

06 Staple Paper Width Adj.

Adjust the width of adjustment plates of the saddle stitcher to be used in Staple mode.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the dispersion [+] To reduce the distortion

07 Staple Center Position

Adjust the center position of staples determined by the saddle stitcher.

Prerequisite: Staple paper width adjustment is completed.

01 2 Position Staple

Adjust the center position for 2-position staple.

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To move rearward [+] To move frontward

02 4 Position Staple(Front 2)

Adjust the center position at two locations on the front edge for 4-position staple.

Objects of adjustment:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm)

Adj. Range: -100~+100 1 step = 0.1 mm

[-] To move rearward [+] To move frontward

03 4 Position Staple(Rear 2)

Adjust the center position at two locations on the rear edge for 4-position staple.

Objects of adjustment:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm)

Adj. Range: -100~+100 1 step = 0.1 mm

[-] To move rearward [+] To move frontward

08 Staple Pitch Adjustment

Adjust the staple pitch determined by the saddle stitcher.

01 2 Position Staple

Adjust the pitch for 2-position staple.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -20~+20 1 step = 1.0 mm

[-] To shorten [+] To lengthen

02 4 Position Staple(Front 2)

Adjust the pitch at two locations on the front edge for 4-position staple.

Objects of adjustment:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm)

Adj. Range: -10~+10 1 step = 1 mm

[-] To shorten [+] To lengthen

03 4 Position Staple(Rear 2)

Adjust the pitch at two locations on the rear edge for 4-position staple.

Objects of adjustment:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm)

Adj. Range: -10~+10 1 step = 1 mm

[-] To shorten [+] To lengthen

09 Staple Offset Adjustment

Adjust the misalignment between the stapling positions and folding line.

Adj. Range: -10~+10 1 step = 0.1 mm

[-] To move leftward [+] To move rightward

10 Staple Tip Adjustment

Change the staple leg shape.

Adj. Range: -9~+9 1 step = 1 msec

[-] To be round [+] To be flat

11 Flattening a Fold(Strength)

Adjust the spine shape while changing the strength to form the book spine.

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To decrease the force [+] To increase the force

12 Flattening a Fold(Freq.)

Adjust the number of roller reciprocation times to form the book spine.

Adj. Range: -5~+5 1 step = 1

[-] To decrease [+] To increase

13 Parallel Trimming Adjustment

Adjust the levelness between the trimming line and cut edge.

Objects of adjustment:

Front, Rear

Adj. Range: 0~+30 1 step = 0.1 mm

[Up the numerical value] To widen

[Down the numerical value] To narrow

14 Fore-edge Trimming Adj.

Adjust the trimming width.

The trimming width should be more than 5 mm, otherwise the trimming operation may not performed properly.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -400~+400 1 step = 0.1 mm

[-] To narrow [+] To widen

15 2-Side Slitting Adjustment

Adjust the 2-side slitting.

Objects of adjustment:

Front, Rear

Adj. Range: -10~+10 1 step = 0.1 mm

[-] To narrow [+] To widen

16 Trimmer Receiver Adj.

Frequent trimming operations may cause damage to the receiver, resulting in trimming failures. Move the receiver automatically or manually.

*Trimmer Receiver Adj. is not displayed by default. To use this setting, please contact your service representative.

Objects of adjustment: Trim Count

Adjustment range: 700 times, 500 times, 300 times

Objects of adjustment: Move Pitch

Adjustment range: 1.0 mm, 1.5 mm, 2.0 mm

Execute Compulsive Movement

02 Finisher Adjustment (Perfect Binder PB-503)

This menu item is to be displayed and allowed on the machine mounted with Perfect Binder PB-503.

05 Perfect Binder Adjustment

01 Sub Compile CD Width Adj.

Adjust misalignment or distortion in the crosswise direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, 16K long edge feed, Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the distortion [+] To reduce the dispersion

02 Clamp CD Width Adjustment

Adjust misalignment or distortion in the crosswise direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, 16K long edge feed, Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the distortion [+] To reduce the dispersion

03 Clamp FD Position Adj.

Adjust misalignment or distortion in the paper feed direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, 16K long edge feed, Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the distortion [+] To reduce the dispersion

04 Glue Start Position

Adjust the position to start gluing on the body. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Ahead: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, 16K long edge feed, Custom(220~379 mm), Custom(148~219 mm)

Back: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, 16K long edge feed, Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -128~+127 1 step = 0.1 mm

[-] To increase [+] To decrease

05 Glue Finish Position

Adjust the position to finish gluing on the body. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Ahead: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, 16K long edge feed, Custom(220~379 mm), Custom(148~219 mm)

Back: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, 16K long edge feed, Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -128~+127 1 step = 0.1 mm

[-] To decrease [+] To increase

06 Cover Lead Edge Adj.

Adjust the position of the lead edge of the left cover sheet. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

PB Tray: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, Custom(220~379 mm), Custom(148~219 mm)

Except PB Tray: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -128~+127 1 step = 0.1 mm

[-] To move closer to the body [+] To move further from the body

07 Cover Trimming Adjustment

Adjust the trimming width of the right cover sheet. To align the lead edges of left and right cover pages, be sure to perform Cover Lead Edge Adjustment in advance.

Objects of adjustment:

Perfect Binder Tray, Except PB Tray

Adj. Range: -128~+127 1 step = 0.1 mm

[-] To narrow [+] To widen

08 Cover Up/Down CD Width Adj.

Adjust the misalignment between the cover sheet and body.

Objects of adjustment:

Perfect Binder Tray, Except PB Tray

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the distortion [+] To reduce the misalignment

09 Spine Corner Forming Pos.

Adjust the spine corners formed in cover sheets.

Objects of adjustment:

Up/Down Forward Adj., Up/Down Rear Adj.

Adj. Range: -128~+127 1 step = 0.1 mm

[-] To convex [+] To concave

10 Temperature Adjustment

Glue Tank -Low:

Adjust the temperature to control the tank heater.

(Temperature low) Down: viscosity increased

(Temperature high) Up: viscosity decreased

Glue Apply Roller:

Adjust the temperature to control the roller heater. This also supports heating of the glue.

(Temperature low) Down: viscosity increased

(Temperature high) Up: viscosity decreased

Object of Adjustment: Glue Tank -Low

Initial: 185°C

Adj. Range: 180~190 1 step = 1 degrees C

Up: viscosity decreased, Down: viscosity increased

Object of Adjustment: Glue Apply Roller

Initial: 165°C

Adj. Range: 160~170 1 step = 1 degrees C

Up: viscosity decreased, Down: viscosity increased

02 Finisher Adjustment (Relay Unit RU-510)

This menu item is to be displayed and become configurable when Relay Unit RU-510 is mounted.

06 Relay Stacker Adjustment

01 Paper Width Adjustment

Adjust the alignment plate position in the crosswise direction of Relay Unit RU-510. Perform this adjustment when paper distortion or skew is detected in the finisher following Relay Unit RU-510.

For example, adjust a misalignment of punch holes in the crosswise direction.

Objects of adjustment:

Offset for All Size, 11 17 short edge feed, A3 short edge feed, B4 short edge feed, 8.5 14 short edge feed, A4 short edge feed, A4 long edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, B5 long edge feed, A5 long edge feed, 5.5 8.5 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 12 18 short edge feed, SRA3 short edge feed, SRA4 long edge feed, 9 11 long edge feed, Postcard, Custom(220~379 mm), Custom(100~219 mm)

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the randomness [+] To reduce the tilts

02 Paper Length Adjustment

Adjust the alignment plate position in the paper feed direction of Relay Unit RU-510. Perform this adjustment when paper distortion or skew is detected in the finisher following Relay Unit RU-510.

For example, adjust a misalignment of punch holes in the paper feed direction.

Objects of adjustment:

Offset for All Size, 11 17 short edge feed, A3 short edge feed, B4 short edge feed, 8.5 14 short edge feed, A4 short edge feed, A4 long edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, B5 long edge feed, A5 long edge feed, 5.5 8.5 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 12 18 short edge feed, SRA3 short edge feed, SRA4 long edge feed, 9 11 long edge feed, Postcard, Custom(380~488 mm), Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To reduce the dispersion [+] To reduce the tilts

03 Process Adjustment

01 Maximum Density Adjustment

Adjust the maximum density. The machine will start the Gamma Automatic Adjustment after you change the maximum density.

Be sure to perform Color Density Manual Control after changing the maximum density.

-10, -9, -8, -7, -6, -5, -4, -3, -2, -1, 0, +1, +2, +3, +4, +5

02 Max. Density Auto Adj. (RU)

Chart printing and scanning are performed automatically, and the maximum density is adjusted automatically. The machine will start the Gamma Automatic Adjustment after you change the maximum density. Be sure to perform Color Density Manual Control after changing the maximum density.

When this machine is equipped with Integrated Color Care Unit IQ-501, 02 Max. Density Auto Adj. is displayed.

-

04 Quality Adjustment

Adjust the image quality.

01 Highlight Adjustment

Change the printer gamma curve to adjust the gradation and background density in highlights.

Screen1, Screen2, Stochastic

Adj. Range: -128~+127

02 Custom Screen

Select screens to be used as Screen1, Screen2, and Stochastic, respectively.

Screen1: Dot210, Dot170, Dot140, Dot120, Dot105, Dot85

Screen2: Dot210, Dot170, Dot140, Dot120, Dot105, Dot85

Stochastic: FM1, FM2, FM3

03 Controller Image Comp. Set

Make this setting to smooth the jagged outlines of the text or line images.

Gradation Priority, Resolution Priority

04 Tone Curve for Each Tag Setting

Select whether or not to allow tone curve adjustment for each tag (image, text/graphic).

Do Not Execute Adjustment, Execute Each Tag Adj.

05 Density Balance Adjustment

01 Density Balance Chart Output

Output the chart for density balance adjustment.

Objects of adjustment:

Measure Spectrophotometer-1 (FD-9), Measure Spectrophotometer-1 (i1-iSisXL), Measure Spectrophotometer-2 (i1-Pro/i1-Pro2)

Type1

Measure Spectrophotometer-3 (FD-5 BT)

Type 1, Type 2

02 Density Balance Data Reg/Del

Load the colorimetric data, or manually register the data on the machine.

05 Corner Staple(Back)Angle

Select between diagonal and parallel stapling on the left corner.

Diagonal, Parallel

06 List/Counter

Outputs User Management List, etc. Also, collectively save data on the USB flash drive connected to the USB port.

User Management List, Use Management List, Font Pattern List

07 Size Setting

Specify the settings related to paper sizes of the paper placed in the Post Inserter.

01 K Size

Specify whether or not to use the K sizes such as 8K and 16K.

ON, OFF

02 A4 Tab Width Setting

Select the tab width of A4-size tab paper.

12.7 mm, 15.0 mm

08 Perfect Binder Setting

This menu item is to be displayed and allowed on the machine mounted with Perfect Binder PB-503.

01 Usable Paper Weight Select

Set the paper weight available for body and cover paper, respectively, when using the perfect binder.

Usable Paper Weight Select

Body: 62-74g/m2/18-19 lb Bond, 75-80g/m2/20-21 lb Bond, 81-91g/m2/22-24 lb Bond, 92-105g/m2/25-28 lb Bond

Cover: 81-91g/m2/22-24 lb Bond, 92-105g/m2/25-28 lb Bond, 106-135g/m2/29-36 lb Bond, 136-162g/m2/37-43 lb Bond, 163-216g/m2/44-57 lb Bond

Change Weight Unit

g/m2, Duodecimo-kg, Octavo-kg, A Book-kg, B Book-kg, lb Bond, lb Index, lb Cover, lb Book, lb Bristol, lb Tag

02 Paper Count Limit for PB

Specify the minimum and maximum numbers of sheets to be bound as a body, individually for each paper weight.

Weight:

62-74/18-19

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 200, 250, 270, 300

75-80/20-21

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 200, 250, 270, 300

81-91/22-24

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 200, 250, 270, 300

92-105/25-28

Minimum Quantity: 10, 15, 20, 25

Maximum Quantity: 200, 250, 270, 300

Change Weight Unit:

g/m2, Duodecimo-kg, Octavo-kg, A Book-kg, B Book-kg, lb Bond, lb Index, lb Cover, lb Book, lb Bristol, lb Tag

03 Unfitting Cover Stop

Specify whether or not to stop the current job when the cover width is not suitable for the body size and spine thickness.

Temporary Stop, Not Temporary Stop

09 Operation Screen Customize

01 Font Weight Setting

Select the font weight for the screen.

Standard, Bold

02 Machine Function Key Setting

Change the layout of function keys displayed on the MACHINE screen.

―

03 Basic Function Display Set.

Hides the buttons at the top of the MACHINE screen.

Recall/Store: ON, OFF

COPY: ON, OFF

SCAN: ON, OFF

Application: ON, OFF

Browser: ON, OFF

1 General Settings

Specify the authentication method of the user authentication and account track.

User Authentication: Authenticate, OFF, External Server Authentication, ON(MFP)

Public User Access: ON (With Login), ON (Without Login), Restrict

Account Track: ON, OFF

Account Track Input Method: Account Name & Password, Password Only

Synchronize User Authentication & Account Track: Synchronize, Do Not Synchronize

When # of Jobs Reach Maximum: Stop Immediately, Stop After Print, Warning Only

Number of User Counters Assigned: 1 to 999 (Default: 500)

Ticket Hold Time Setting: 1 minute to 600 minutes (Default: 600)

Count Sample Print: Yes, No

2 User Authentication Settings

1 Administrative Settings

Specify whether or not to display the user name list on the authentication screen. Also place the default function permissions on users for the authentication by an external server.

User Name List: ON, OFF

Default Function Permission

Print: Allow, Restrict

User Box: Allow, Restrict

2 User Registration

Add, change, or delete entries of users to be allowed in user authentication.

User No., User Name, Password, E-mail Address, Account Name, Max. Allowance Set, Function Permission (Print, User Box)

3 User Counter

View or reset the count for each user.

―

3 Account Track Settings

1 Account Track Registration

Change, add, or delete accounts to be tracked.

Account Name, Password, Max. Allowance Set, Function Permission (Print, User Box)

2 Account Track Counter

View or reset the count for each account track.

―

4 Print without Authentication

Specify whether to make print function available to users without authentication.

Allow, Restrict

6 External Server Settings

Register an external server, or edit or delete a registered server when External Server Authentication is selected as the Authentication Method.

―

8 Authentication Device Settings

1 General Settings

Specify the type of IC card used for entering credentials. Also, specify the authentication method.

IC Card Type Setting: FeliCa, SSFC, FCF, FCF (Campus), Type A, Felica+TypeA, SSFC+TypeA, FCF+TypeA, FCF (Campus) +TypeA

Operation Setting: IC Card Authentication, IC Card + Password Authentication

9 User/Account Common Setting

Specify whether or not to display a logout confirmation dialog.

Logout Confirmation Screen Display Setting: ON, OFF

01 NIC Settings

Configure various NIC settings.

TCP/IP Settings, HTTP Server Settings, FTP Settings, SMB Settings, LDAP Settings, E-mail Settings, SNMP Settings, Bonjour Setting^*, TCP Socket Settings, WebDAV Settings, DPWS Settings, SSDP Settings, Detail Settings, IEEE802.1x Authentication Settings, IWS Settings, Remote Panel Settings, JSP Setting, Hot Folder Setting, AccurioPro Print Manager Setting

* To connect Bonjour in Macintosh, you need to configure TCP/IP setting in advance.

02 E-mail Initial Setting

Configure initial settings for e-mail or perform transmitting/receiving test.

Use E-mail System: ON, OFF

Time Zone: -1200 to +1200 (Default: 0)

Trans(SMTP) Mail Server: Max. 128 characters (Default: 0.0.0.0)

SMTP Port Number: 0 to 65535 (Default: 25)

Trans Mail Server Timeout: 30 seconds to 5 minutes (Default: 5 minutes)

New-arrival Check Interval: 1 to 60 minutes (Default: 0)

Receive Mail Server: Max. 128 characters (Default: 0.0.0.0)

Receive Mail Server Type: POP3, IMAP

POP3/IMAP Port Number: 0 to 65535 (Default: POP3-110, IMAP-143)

Receive Mail Account: Max. 64 characters

Receive Mail Password: Max. 64 characters

E-mail Address for Machine: Max. 128 characters

POP(IMAP) before SMTP Auth.: ON, OFF

SSL Encryption of SMTP: ON, OFF

SSL Encryption of POP(IMAP): ON, OFF

SMTP Authentication: ON, OFF

SMTP Authentication User ID: Max. 64 characters

SMTP Authentication Password: Max. 64 characters

Test

03 http Communication Setting

Configure the http communication settings.

Enable Proxy Server: ON, OFF

Proxy Server Address: Max. 128 characters

Proxy Server Port: 0 to 65535 (Default: 8080)

Enable SSL: ON, OFF

Enable Authentication: ON, OFF

Authentication User Name: Max. 20 characters

Authentication Password: Max. 20 characters

04 Quick Security Setting

01 Quick IP Filtering

Restrict access to the machine by means of IP address (IPv4/IPv6).

Filtering Method: No Filtering, Sync. IP Address, Sync. Subnet Mask

IPv4 Access Range, IPv6 Access Range

02 Administrator Password

Set an administrator password for the machine on which the administrator authentication function is set to OFF. The administrator authentication function is automatically turned ON.

Current Password, New Password, Input Confirmation

For details about the default administrator password, refer to Safety Information.

03 Password Rules Setting

Select whether or not to enable the password rules.

Password Rules Setting: Enable, Disable

Set Minimum Password Length: 8 to 64 characters

04 WebUtilities Setting

Select whether or not to use the functionality of Web Utilities.

ON, OFF

05 PSWC Setting

Select whether or not to use the PageScope Web Connection function.

Enable, Disable

06 Security Warning Display

Select whether or not to display the Security Setting Warning screen.

Display, Not Display

05 Auto Inspection NIC Setting

Selecting Auto Inspection NIC Setting allows you to check the automatic inspection report from Web Utilities of the Auto Inspection Unit UK-301. This value is set by default at the time of installation.

This item is displayed and available when Auto Inspection Unit UK-301 is mounted.

IP Address, Subnet Mask, Gateway Address

Line Speed Setting: Auto Negotiation, 10M Half Duplex, 10M Full Duplex, 100M Half Duplex, 100M Full Duplex

One Shot Message Indication Time

Select the time span to display a shot message in the message area of the touch panel.

3 seconds, 5 seconds

Offset by Job Unit

Specify whether or not to offset the output sheets by job. Also specify the number of jobs to be offset when selecting ON for this function.

ON, OFF (Selecting ON: Offset Job Number)

Continuation Print

Specify whether or not to output multiple reserve jobs in succession without stopping the machine at a job break.

Printer ON, Printer OFF

Dark Tone Control

In order to adjust the quality of the output image, select whether to automatically decrease the output speed (Quality), prioritize the output speed, or disable the ability to control the tone.

OFF, Quality, Performance

Icon Display for Dark Tone Control

Select whether or not to display the Dark Tone icon while the Dark Tone Control function is enabled.

This function is available only when Quality or Performance is selected at Dark Tone Control.

ON, OFF

Dash Length(Page Stamp)

Select the length of the dash to be used in a style of Page No. in Stamp.

Long, Short

Center Crop Mark Trim Margin

Specify the space between the center crop mark and image area (center crop mark trim margin).

0.0 mm-20.0 mm (Default: 1.0)

Schedule Cross Axis Unit (Default)

Select the unit of horizontal axis on the Schedule screen.

Timetable, Time Frame(m), Sheet Volume

Hold Job Status after Output (Default)

Select the default value to delete or save the data of hold job after outputting.

Delete, Save

Hold Job Direct Output (Default)

Select the default for the Direct Output check box under the Hold Job screen.
ON selects the check box, and OFF clears the check box.
After the change, turn OFF/ON the sub power switch to apply the setting.

ON, OFF

Offset Output Mode

Specify how to offset the output sets.

Change Out Pos., Stop Print, Change Out Pos. + Partition Paper (Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11, PI1, PI2, PI-PFU1, PI-PFU2, PI-PFU3), Partition Paper (Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11, PI1, PI2, PI-PFU1, PI-PFU2, PI-PFU3)

Needless Tab Paper Exit

Specify whether or not to automatically discharge the oddments of tabbed sheets loaded in a tray as a set.

ON, OFF

Remaining Memory (Measurement Unit)

Select the unit of displaying the remaining memory.

%, GB

Remaining Memory (Warning)

Select the percentage at which to give warning when the remaining memory is low.

5% or Less, 10% or Less

[Proof Copy] 1 Set/1st Sheet Selection

If it is turned ON, the confirmation window is opened and you are asked to output one confirmation copy or to output only its first page when the Proof Copy is pressed.

ON, OFF

Temp. Down/Up Control before Print

Select whether to rotate the fusing roller before printing starts, in order to print at the appropriate temperature.

ON, OFF

Both Sides Rotate/Skew

If Disable is selected, the Rotate/Skew adjustment does not become available and does not function.

Enable, Disable

Stop when Water Tank Near Empty

Select whether to temporarily stop a job when the humidifier tank runs low on water.

Temporary Stop, NotTemporaryStop

Select Chart Type (Auto Image Adj.)

Select an automatic image adjustment chart for each paper weight. The unit of weight can be switched.

This option is displayed when Integrated Color Care Unit IQ-501 is mounted on the machine.

40-49g/m2/10-13 lb Bond: Type1, Type2

50-54g/m2/14-15 lb Bond: Type1, Type2

55-61g/m2/16-17 lb Bond: Type1, Type2

62-74g/m2/18-19 lb Bond: Type1, Type2

75-80g/m2/20-21 lb Bond: Type1, Type2

81-91g/m2/22-24 lb Bond: Type1, Type2

92-105g/m2/25-28 lb Bond: Type1, Type2

106-135g/m2/29-36 lb Bond: Type1, Type2

136-162g/m2/37-43 lb Bond: Type1, Type2

163-216g/m2/44-57 lb Bond: Type1, Type2

217-256g/m2/58-68 lb Bond: Type1, Type2

257-300g/m2/69-81 lb Bond: Type1, Type2

301-350g/m2/82-93 lb Bond: Type1, Type2

Change Unit

Auto Image Adjustment Deviation Check

Select whether to automatically check a deviation. If you select ON, enter the specified value of a deviation.

This option is displayed when Integrated Color Care Unit IQ-501 is mounted on the machine.

ON (ON: 0.5 mm-10.0 mm, Default: 2.0), OFF

Operation after Deviation/Out of Range was Detected

Specify the operation to be performed when inappropriate output paper is detected.

You can specify whether to stop this machine immediately or only when the number of detected errors exceeds the standard.

* When the standard value for the number of detected errors is set to 0, and Automatic Reprint when Deviation/Out of Range was Detected is set to OFF, this machine will not stop even if the number of detected errors increases.

This option is displayed when Integrated Color Care Unit IQ-501 is mounted on the machine.

Stop, Continue Output, Detection Count (0 ~ 10 times)

Partition Paper when Deviation/Out of Range was Detected

Configure a setting to insert partition paper when inappropriate output paper is detected.

When inserting, select the paper tray to load partition paper into.

This option is displayed when Integrated Color Care Unit IQ-501 is mounted on the machine.

ON, OFF, Partition Paper (Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11)

Automatic Reprint when Deviation/Out of Range was Detected

Configure a setting to perform reprinting when inappropriate output paper is detected. When reprinting is performed, paper in the machine is output once, so a page order error involving output paper does not occur.

This option is displayed when Integrated Color Care Unit IQ-501 is mounted on the machine.

ON, OFF

Output Tray for Out of Range

Specify the tray to output paper that does not satisfy the standard. You can combine the Purge Tray of the Relay Unit RU-702 with a sub tray of the optional output unit mounted later, and also select the same tray for a job.

* Paper cannot be output to the sub tray of Folding Unit FD-503, Large Capacity Stacker LS-506, or Saddle Stitcher SD-506. Also, paper cannot be output to the sub tray of Saddle Stitcher SD-513 when the Multi Tri-Fold, Fold & Staple, or Half-Fold mode is being used.

* When a paper output enabled option is not connected to Relay Unit RU-702 or later, the button of RU702 + Sub Tray is grayed out.

This option is displayed when Integrated Color Care Unit IQ-501 is mounted on the machine.

Same as the Job, Purge Tray (RU702 Only, RU702 + Sub Tray)

Create Auto Inspection Report

Configure a setting to create an automatic inspection result report.

When inappropriate output paper is not discharged automatically, the user deals with the inappropriate output paper based on the report.

This option is displayed when Auto Inspection Unit UK-301 is mounted.

ON, OFF

Automatic Inspection Level Setting

Adjust the detection standard for automatic inspection. There are three levels: Essential, Standard, and Premium, for each of which you can adjust the detection standard.

This option is displayed when Auto Inspection Unit UK-301 is mounted.

Spot Detection Level

Specify the reference value of the spot size. A spot that is over the reference size value is detected as an image failure.

Range: 1(Large) ~ 7(Small)

Paper Noise Removal Level

Specify the reference value of spot density. A spot that is over the reference density value is detected as an image failure.

Range: 1(Strong) ~ 7(Weak)

Image Edge Detection Sensitivity

Specify the sensitivity of the inspection area around the edge of the image. A slight image misalignment may occur around the edge of the image even if no image failure is detected; therefore, if the sensitivity is set to a higher level, it may lead to frequent reprinting.

Range: 1(Low) ~ 7(High)

Permission Level for Spot

Specify the reference value that permits an image spot detected in a reference image.

An image failure may be slipped into a reference image when it is created. If automatic inspection is performed in this status, the inspection image is detected as an error even if there is "no error". In such a case, reduce this reference value; an image failure of a reference image is permitted to a certain degree, which enables smooth printing.

Range: 1(Large) ~ 7(Small)

Wait Screen for Automatic Inspection

Set the automatic inspection on the Wait screen. When outputting a print job for Direct Print and such without temporarily saving it, input the job in Wait mode; you can set the automatic inspection.

This option is displayed when Auto Inspection Unit UK-301 is mounted.

ON, OFF

Reference Image Automatic Deletion

Configure a setting to automatically delete the reference image that is created for automatic inspection. When the amount of available reference image memory is not sufficient, the reference image of the oldest update date and time in Reference Image List 1 is deleted automatically.

This option is displayed when Auto Inspection Unit UK-301 is mounted.

ON, OFF

1 OpenAPI Settings

Set the OpenAPI information.

Access Setting: Allow, Restrict

SSL/Port Settings

Authentication: ON, OFF, Login Name, Password

Proxy Settings: Port Number(HTTP) (Default: 8080), Port Number(HTTPS) (Default: 8080), Port Number(FTP) (Default: 21), Host Address, User Name, Password

Specified Application Start Setting: Enable, Invalid

Default Startup Application Selection

Basic Functions Setting: Allow, Restrict

Single Sign-On Settings: Authentication Info. Reference, Enable ALL, Individual Settings, Detail

2 Call Remote Center

Press Start to call your service representative via CS Remote Care.

Start

3 Browser Screen Setting

OpenAPI/IWS Appli. Size Set.

Specify the screen size of the OpenAPI or IWS application.

Small Size, Large Size

Screen Saver Size Setting

Specify the screen size of the screen saver.

Small Size, Large Size

01 Administrator Password

Change the administrator password.

For details about the default administrator password, refer to Safety Information.

02 HDD Management Setting

01 HDD Lock Password

Change the HDD lock password.

―

02 Delete Temp. Data Setting

Specify whether or not to overwrite the temporary image data on the memory. Select the erase mode to overwrite and delete data.

Setting Switch: ON, OFF

Erase Mode: Mode 1, Mode 2

03 Delete All Data Setting

Select the desired erase mode to delete all the data on the HDD or the non-volatile memory of this machine. Also execute deleting all the data.

Erase Mode: Mode 1, Mode 2, Mode 3, Mode 4, Mode 5, Mode 6, Mode 7, Mode 8

Execute Deletion

04 Delete Hold Job

Use this function to delete hold jobs.

―

05 Delete HDD Job

Use this function to delete the jobs saved on the HDD.

―

06 Delete Secure Job

Use this function to delete secure jobs from the security job box.

―

07 HDD Restore/Backup

Make a backup of, or restore the HDD.

01 HDD ALL Backup

Create a backup of all the hold job and HDD job saved on the HDD onto an external storage medium connected to the USB port.

Start